Acura RSX Honda Integra. Manual — part 382
02
01
S6M6A00J26220219281KDAT00
Special Tools Required
20-65
20-65
Dashboard Center Lower Cover
Removal/Installation
Fastener Locations
: Screw, 2
A
B
Fastener Locations
: Clip, 3
A
D
C
B
B
3. If necessary, remove the screws securing the
driver’s center vent (A), then separate it from the
heater control panel (B).
4. Install the panel in the reverse order of removal,
and note these items:
• Make sure the climate control unit connector is
plugged in properly.
• Replace any damaged or stress-whitened clips.
• Push the clips and hooks into place securely.
KTC trim tool set SOJATP2014
NOTE:
• Use the appropriate tool from the KTC trim tool set to
avoid damage when prying components.
• Take care not to scratch the dashboard and related
parts.
1. Remove the dashboard center lower cover (A).
–1 Gently pull out the cover to release the clips
and hooks (B).
–2 If equipped, disconnect the accessory power
socket connector (C) and seat heater switch
connector (D).
2. Install the cover in the reverse order of removal,
and note these items:
• If equipped, make sure the accessory power
socket connector and seat heater switch
connector are plugged in properly.
• Replace any damaged or stress-whitened clips.
• Push the clips and hooks into place securely.
05/06/27 18:23:50 61S6M040_200_0066
01
S6M6A00J26220219291KDAT01
Special Tools Required
20-66
Dashboard
Center Panel Removal/Installation
Fastener Locations
: Bolt, 2
D
B
E
F
G
5 x 0.8 mm
5 N·m (0.5 kgf·m,
4 lbf·ft)
C
D
D
C
C
: Clip, 3
C
: Clip, 3
D
B
B
A
KTC trim tool set SOJATP2014
NOTE:
• Use the appropriate tool from the KTC trim tool set to
avoid damage when prying components.
• Take care not to scratch the dashboard and related
parts.
1. Remove the dashboard center lower cover
(see page 20-65).
2. Make sure you have the anti-theft code for the radio,
then write down the frequencies for the preset
buttons.
3. Remove the center panel (A).
–1 Remove the bolts (B) from the dashboard
center lower cover opening.
–2 Gently pull out along the bottom to release the
lower clips (C, D), then along both sides and
top to release the remaining clips (C).
–3 Disconnect the hazard warning switch
connector (E), audio unit connector (F), and
antenna lead (G).
4. Install the panel in the reverse order of removal,
and note these items:
• Make sure each connector is plugged in properly
and antenna lead is connected properly.
• Enter the anti-theft code for the radio, then enter
the customer’s radio station presets.
• Replace any damaged or stress-whitened clips.
• Push the clips into place securely.
• Reset the clock.
• ’02-04 models: Do the ECM/PCM idle learn
procedure (see page 11-349).
05/06/27 18:23:50 61S6M040_200_0067
01
S6M6A00J26220219301KDAT02
01
02
S6M6A00J26220230101KDAT01
20-67
20-67
Passenger’s Dashboard Lower
Cover Removal/Installation
Glove Box Removal/Installation
Fastener Locations
: Clip, 3
A
B
A
B
Fastener Locations
5 x 0.8 mm
5 N·m
(0.5 kgf·m, 4 lbf·ft)
: Bolt, 2
NOTE: Take care not to scratch the dashboard and
related parts.
1. Remove the passenger’s dashboard lower cover
(A).
–1 Remove the clips.
–2 Pull down the edge nearest the glove box.
–3 Pull the cover away to release it from the
holders (B).
2. Install the cover in the reverse order of removal,
and note these items:
• Replace any damaged or stress-whitened clips.
• Push the clips into place securely.
SRS components are located in this area. Review the
SRS component locations (see page 23-10) and the
precautions and procedures (see page 23-11) before
performing repairs or service.
NOTE: Take care not to scratch the dashboard and
related parts.
1. Remove the passenger’s dashboard lower cover.
2. While holding the glove box (A), remove the glove
box stop (B) on each side.
3. Remove the bolts, then remove the glove box.
4. Install the glove box in the reverse order of
removal.
05/06/27 18:23:51 61S6M040_200_0068
02
03
S6M6A00J26220219251KDAT02
01
S6M6A00J26220219251KDAT01
Special Tools Required
20-68
20-68
Dashboard
Driver’s Side Vent Panel Removal/
Installation
Passenger’s Side Vent Removal/
Installation
B
: Clip, 2
C
: Clip, 2
: Screw, 2
A
Fastener Locations
B
B
C
C
Fastener Locations
A
B
B
Fastener Locations
Fastener Locations
: Screw, 3
Center
Side
A
C
C
B
A
C
C
B
KTC trim tool set SOJATP2014
NOTE:
• Use the appropriate tool from the KTC trim tool set to
avoid damage when prying components.
• Take care not to scratch the dashboard and related
parts.
1. Gently pry up on the driver’s side vent panel (A) to
detach the clips (B, C), then pull out and remove it.
2. If necessary, remove the screws securing the
driver’s side vent (A), then separate it from the
panel (B).
3. Install the panel in the reverse order of removal,
and note these items:
• Replace any damaged or stress-whitened clips.
• Push the clips into place securely.
NOTE:
• Put on gloves to protect your hands.
• Take care not to scratch the dashboard and related
parts.
1. Remove the glove box (see page 20-67).
2. Remove the screws securing the passenger’s vent
(A) and the air conditioner duct (B), and the screws
securing the passenger’s vent to the dashboard.
3. Install the vent in the reverse order of removal, and
note these items:
• When installing the vent, wrap its panel surface
with tape to prevent damage.
• Align the holes in the vent with the pins (C) on
the dashboard.
05/06/27 18:23:51 61S6M040_200_0069
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст