Acura RSX Honda Integra. Manual — part 315
09
14-386
Shafts and Clutches
Clutch Reassembly (cont’d)
18. Install the snap ring with a screwdriver.
19. Check that the clutch piston moves by applying air
pressure into fluid passage.
05/06/27 17:59:38 61S6M040_140_0387
*02
S6M6A02E10480139301KCAT20
Exploded View
14-387
Valve Body
Valve Body and ATF Strainer Installation
6 x 1.0 mm
Two Bolts
ATF STRAINER
O-RING
6 x 1.0 mm
13 Bolts
ATF FEED PIPE,
8 x 220 mm
6 x 1.0 mm
One Bolts
REGULATOR
VALVE BODY
6 x 1.0 mm
Seven Bolts
ATF FEED PIPE,
8 x 198 mm
ATF JOINT
PIPES
O-RING
STATOR SHAFT STOP
DOWEL PIN
REGULATOR
SEPARATOR
PLATE
STATOR SHAFT
SERVO BODY
DOWEL PIN
SERVO SEPARATOR
PLATE
8 x 1.25 mm
Three Bolts
COOLER CHECK
VALVE
MAIN VALVE BODY
ATF PUMP DRIVEN
GEAR SHAFT
ATF PUMP DRIVEN
GEAR
MAIN
SEPARATOR
PLATE
DOWEL PIN
ATF PUMP DRIVE
GEAR
TORQUE CONVERTER HOUSING
COOLER CHECK
VALVE SPRING
COOLER CHECK
VALVE (BALL)
Torque Specifications:
6 x 1.0 mm: 12 N·m (1.2 kgf·m, 8.7 lbf·ft)
8 x 1.25 mm: 18 N·m (1.8 kgf·m, 13 lbf·ft)
(cont’d)
Replace.
Replace.
05/06/27 17:59:38 61S6M040_140_0388
02
03
14-388
Valve Body
Valve Body and ATF Strainer Installation (cont’d)
D
B
C
A
A
B
NOTE: Refer to the Exploded View as needed during the
following procedure.
1. Install the main separator plate (A) and two dowel
pins on the torque converter housing. Then install
the ATF pump drive gear (B), driven gear (C), and
ATF pump driven gear shaft (D). Install the ATF
pump driven gear with its grooved and chamfered
side facing down.
2. Install the main valve body.
3. Make sure the ATF pump drive gear (A) rotates
smoothly in the normal operating direction, and the
ATF pump driven gear shaft (B) moves smoothly in
the axial and normal operating direction.
4. If the ATF pump drive gear and ATF pump driven
gear shaft do not move smoothly, loosen the main
valve body bolts. Realign the ATF pump driven
gear shaft, and retighten the bolts to the specified
torque, then recheck. Failure to align the ATF pump
driven gear shaft correctly will result in a seized
ATF pump drive gear or ATF pump driven gear
shaft.
5. Make sure that the check balls (two) are in the main
valve body, then install the cooler check valve and
the cooler check valve spring.
NOTE:
• Cooler check valve (ball) applies to the 2002
model; transmission number 1000001-1006166.
• Cooler check valve applies to the 2002 model;
transmission number 1006167 or later, and
2003-2006 models.
6. Install the regulator separator plate and dowel pins
(two) on the main valve body.
7. Install the stator shaft and stator shaft stop.
8. Install the regulator valve body (seven bolts).
9. Install the servo separator plate and dowel pins
(two) on the main valve body.
10. Install the servo body (13 bolts).
11. Install the ATF strainer (two bolts).
12. Install the ATF joint pipes (one bolt).
13. Install the ATF feed pipes in the regulator valve
body and servo body.
05/06/27 17:59:39 61S6M040_140_0389
*01
S6M6A02E10410459801KCAT00
Exploded View
14-389
Transmission Housing
Shaft Assembly and Housing Installation
TRANSMISSION HOUSING
MOUNTING BOLTS
10 x 1.25 mm
44 N·m (4.5 kgf·m, 33 lbf·ft)
19 Bolts
REVERSE
SHIFT FORK
SECONDARY
SHAFT
SUBASSEMBLY
DIFFERENTIAL
ASSEMBLY
TRANSMISSION
HANGER
INPUT SHAFT
(MAINSHAFT)
SPEED SENSOR
MAINSHAFT
SUBASSEMBLY
TRANSMISSION
HOUSING GASKET
NEEDLE
BEARING
REVERSE
SELECTOR
O-RINGS
6 x 1.0 mm
14 N·m (1.4 kgf·m,
10 lbf·ft)
DOWEL
PINS
COUNTERSHAFT
REVERSE GEAR
LOCK WASHER
COUNTERSHAFT
SUBASSEMBLY
OUTPUT SHAFT
(COUNTERSHAFT)
SPEED SENSOR
ATF FEED PIPE
ATF LUBRICATION
PIPE
SHIFT SOLENOID
VALVE COVER
GASKET
HARNESS CLAMP
BRACKET
SELECTOR CONTROL LEVER
LOCK WASHER
SELECTOR
CONTROL
SHAFT
(cont’d)
Replace.
Replace.
Replace.
Replace.
Replace.
05/06/27 17:59:39 61S6M040_140_0390
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст