Acura RSX Honda Integra. Manual — part 336
02
03
03
Special Tools Required
Removal
Disassembly
17-37
A
A
A
A
B
• Cylinder end seal remover attachment
07NAD-SR30200 or 07NAD-SR3020A
• Driver, 27 mm 07ZAF-S5A0100
• Valve seal ring sizing tool
07NAG-SR30900 or 07NAG-SR3090A
• Sleeve seal ring guide 07YAG-S2X0100
• Sleeve seal ring sizing tool, 36 mm 07ZAG-S5A0100
• Attachment, 32 x 35 mm 07746-0010100
• Driver 07749-0010000
• Piston seal ring guide, 42 mm 07ZAG-S7A0100
• Piston seal ring sizing tool, 42 mm 07ZAG-S7A0200
• Piston seal ring guide, 44 mm 07XAG-S0KA200
• Piston seal ring sizing tool, 44 mm 07XAG-S0KA100
• Pilot collar 07GAF-PH70100
• Locknut wrench 07ZAA-S5A0100
• Driver handle 07NAD-SR30101
• Cylinder end seal slider
07974-6890801 or 07974-689080A
• Valve seal ring guide 07ZAG-S5A0200
• Pincers, Oetiker 1098 or equivalent, commercially
available
NOTE: Refer to the Exploded View as needed during
this procedure.
1. Remove the steering gearbox (see page 17-32).
2. Remove cylinder lines (A) from the steering
gearbox.
3. Drain the fluid from the cylinder fittings by slowly
moving the steering rack back and forth.
4. Unbend the lock washers (A).
5. Hold the bracket (A) with one wrench, and unscrew
both rack ends (B) with another wrench. Remove
the lock washers.
(cont’d)
05/06/27 18:15:15 61S6M040_170_0038
35
04
06
07
17-38
Power Steering
Steering Gearbox Overhaul (cont’d)
A
B
C
D
D
F
B
E
C
A
E
D
C
B
A
A
B
6. Remove the stop washer (A), the 12 mm flange
bolts (B), O-rings (C), and bracket (D) from the
steering gearbox.
7. Remove the boot guard (A) by removing the 8 mm
flange bolt (C) on the rack end.
8. Remove the boot band (D) and clip (E). Pull the boot
B away from the end of the steering gearbox.
Remove the rack end plug (F).
9. Loosen the locknut (A), then remove the rack guide
screw (B), spring (C), disc washer (D), and rack
guide (E) from the steering gearbox.
10. Remove the snap ring (A) and backup ring (B) from
the cylinder housing.
05/06/27 18:15:16 61S6M040_170_0039
08
09
10
11
17-39
A
B
B
B
A
C
B
A
B
C
A
07ZAA-S5A0100
11. Remove the valve body unit (A) from the steering
gearbox. Remove the O-ring (B) and discard it.
12. Remove the two boot bands (B) from boot A.
Compress boot A by hand, and apply vinyl tape (C)
so the boots stay collapsed and pulled back.
13. Hold the gearbox housing using a C-clamp
(commercially available) (A) and the wooden
blocks (B) as shown. Do not clamp the cylinder part
of the housing or gearbox housing in the vise.
14. Install the special tool (A) on the lock screw (B),
then loosen and remove the lock screw from inside
of the gearbox housing (C).
(cont’d)
05/06/27 18:15:16 61S6M040_170_0040
12
05
04
15
17-40
Power Steering
Steering Gearbox Overhaul (cont’d)
A
B
A
25.3 mm
(0.925 in.)
A
25.3 mm
(0.925 in.)
A
B
B
C
A
15. Remove the special tool.
16. Pull on the cylinder to remove it from the gearbox
housing. Remove boot A and the slider guide (B)
from the cylinder.
17. Check the slider guide for damage and cracks. Use
vernier calipers to measure the thickness of the
slider guide. If the thickness is less than the service
limit (A), replace the slider guide.
18. Remove and discard the stop ring (A) on the
cylinder by expanding it with snap ring pliers.
Remove and discard the lock screw (B).
19. Set the cylinder housing (A) in a press so the
cylinder side points downward, then press the
cylinder end seal (B) and steering rack (C) out of the
cylinder. Hold the rack to keep it from falling when
pressed clear.
20. Remove the cylinder end seal from the steering
rack.
05/06/27 18:15:42 61S6M040_170_0041
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст