Acura RSX Honda Integra. Manual — part 289
01
S6M6A02E10410422251KDAT00
14-281
Drive Plate Removal and Installation
12 x 1.0 mm
74 N·m (7.5 kgf·m, 54 lbf·ft)
A
B
1. Remove the transmission assembly (see page
14-273).
2. Remove the drive plate (A) and washer (B) from the
crankshaft.
3. Install the drive plate and washer on the engine
crankshaft, and tighten the eight bolts in a
crisscross pattern in two or more steps.
4. Install the transmission (see page 14-282).
05/06/27 17:57:47 61S6M040_140_0282
01
01
01
02
S6M6A02E10410400000KCAT00
Special Tools Required
14-282
Automatic Transmission
Transmission Installation
6 x 1.0 mm
12 N·m
(1.2 kgf·m,
8.7 lbf·ft)
12 x 1.25 mm
64 N·m (6.5 kgf·m, 47 lbf·ft)
12 x 1.25 mm
64 N·m (6.5 kgf·m, 47 lbf·ft)
12 x 1.25 mm
54 N·m
(5.5 kgf·m, 40 lbf·ft)
12 x 1.25 mm
64 N·m
(6.5 kgf·m, 47 lbf·ft)
D
A
C
D
B
• Engine hanger adapter EQS00BRSX0
• Engine support hanger, A and Reds AAR-T-12566
(Available through the Acura Tool and Equipment
Program 1-888-424-6857)
• Front subframe adapter EQS02C000011
NOTE: Use fender covers to avoid damaging painted
surfaces.
1. Clean the ATF cooler (see page 14-291).
2. Install the air cleaner housing mounting bracket.
3. Install the front mount.
4. Install the rear mount/bracket.
5. Install the torque converter assembly (A) on the
mainshaft (B) with the new O-ring (C).
6. Install the 14 x 20 mm dowel pins (D) in the torque
converter housing.
05/06/27 17:57:48 61S6M040_140_0283
04
03
06
14-283
12 x 1.25 mm
64 N·m (6.5 kgf·m, 47 lbf·ft)
12 x 1.25 mm
64 N·m (6.5 kgf·m, 47 lbf·ft)
12 x 1.25 mm
64 N·m (6.5 kgf·m, 47 lbf·ft)
12 x 1.25 mm
64 N·m (6.5 kgf·m, 47 lbf·ft)
7. Place the transmission on a jack, and raise the
transmission to engine level.
8. Attach the rear transmission to the engine, then
install the transmission housing mounting bolts.
9. Install the front transmission housing mounting
bolts.
10. Install the upper transmission housing mounting
bolts.
(cont’d)
05/06/27 17:57:48 61S6M040_140_0284
*01
*02
08
2002-2003 models:
2004-2006 models:
14-284
Automatic Transmission
Transmission Installation (cont’d)
12 x 1.25 mm
54 N·m (5.5 kgf·m, 40 lbf·ft)
A
B
12 x 1.25 mm
54 N·m
(5.5 kgf·m, 40 lbf·ft)
12 x 1.25 mm
54 N·m (5.5 kgf·m, 40 lbf·ft)
A
B
12 x 1.25 mm
54 N·m
(5.5 kgf·m, 40 lbf·ft)
D
8 x 1.25 mm
22 N·m
(2.2 kgf·m, 15 lbf·ft)
F
8 x 1.25 mm
22 N·m
(2.2 kgf·m,
16 lbf·ft)
C
B
E
8 x 1.25 mm
22 N·m
(2.2 kgf·m,
16 lbf·ft)
10 x 1.25 mm
39 N·m
(4.0 kgf·m, 29 lbf·ft)
A
11. Install the transmission mount bracket (A). Tighten
the mount bolt (B) loosely, and tighten the
transmission mount bracket bolt and nuts to the
specified torque, then tighten the mount bolt to the
specified torque.
12. Install the new set ring (A) on the intermediate shaft
(B).
13. Clean the areas where the intermediate shaft
contacts the transmission (differential) with solvent
or carburetor cleaner, and dry with compressed air.
Then install the intermediate shaft in the
differential. While installing the intermediate shaft,
be sure not to allow dust or other foreign particles
to enter the transmission.
14. Install the intermediate shaft cover (C) with
installing the mounting bolts loosely.
15. First tighten the right upper bolt (D) on the cover,
then right lower bolt (E), and lastly the left bolt (F).
05/06/27 17:57:49 61S6M040_140_0285
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст