Acura RSX Honda Integra. Manual — part 30
02
10
11
03
4-56
Charging System
Alternator Overhaul (cont’d)
07749-0010000
07746-0010300
12. With a hammer and commercially available tools
shown, install a new rear bearing on the rotor shaft.
13. Remove the front bearing retainer plate.
14. Support the stator housing in a vise, and drive out
the front bearing with a brass drift and hammer.
15. With a hammer and the special tools, install a new
front bearing in the stator housing.
04
05
06
Rectifier Test
Alternator Brush Inspection
Alternator Brush Length
Standard (New): 10.5 mm (0.41 in.)
Service Limit:
1.5 mm (0.06 in.)
Rotor Slip Ring test
4-57
P’
B
P
P
P
P
E
P’
E
P
P
P
P
B
A
B
A
B
C
1
1
2
3
4
1
4
3
2
1
16. Check for continuity in each direction, between the
B terminal and P terminals, and between the E
terminal and P terminals of each diode pair.
All diodes should have continuity in only one
direction. Because the rectifier diodes are designed
to allow current to pass in one direction, and the
rectifier is made up of eight diodes (four pairs), you
must test each diode in both directions for
continuity with an ohmmeter that has diode
checking capability: a total of 16 checks.
• If any diode is faulty, replace the rectifier
assembly. (Diodes are not available separately.)
• If all the diodes are OK, go to step 17.
17. Measure the length of both brushes (A) with a
vernier caliper (B).
• If either brush is shorter than the service limit,
replace the brush assembly.
• If brush length is OK, go to step 18.
18. Check for continuity between the slip rings (A).
• If there is continuity, go to step 19.
• If there is no continuity, replace the alternator.
19. Check for continuity between each slip ring and the
rotor (B) and the rotor shaft (C).
• If there is no continuity, go to step 20.
• If there is continuity, replace the alternator.
(cont’d)
09
Stator Test
4-58
Charging System
Alternator Overhaul (cont’d)
A
B
20. Check for continuity between each pair of leads (A).
• If there is continuity, go to step 21.
• If there is no continuity, replace the alternator.
21. Check for continuity between each lead and the coil
core (B).
• If there is no continuity, go to step 22.
• If there is continuity, replace the alternator.
22. Assemble the alternator in the reverse order of
disassembly, and note these items:
• Be careful not to get any grease or oil on the slip
rings.
• If you removed the pulley, tighten its locknut to
111 N·m (11.3 kgf·m, 81.7 lbf·ft) when you install
it.
*01
*02
S6M6A20A14500000000DAAT00
4-59
Cruise Control
Component Location Index
CRUISE CONTROL
MAIN SWITCH
CLUTCH PEDAL POSITION
SWITCH (M/T)
BRAKE PEDAL POSITION SWITCH
CRUISE CONTROL UNIT
CRUISE CONTROL INDICATOR
(Built into gauge assembly)
CRUISE CONTROL
SET/DECEL, RESUME/ACCEL,
CANCEL SWITCH
CRUISE CONTROL
ACTUATOR
ACTUATOR CABLE
TRANSMISSION RANGE
SWITCH (A/T)
Test/Replacement, page 4-67
Test, page 4-71
Clutch Pedal Adjustment, page 12-6
Test, page 22-95
Pedal Height Adjustment, page 19-6
Input Test, page 4-64
Test/Replacement, page 4-68
Test, page 4-68
Replacement, page 4-69
Adjustment, page 4-71
Test, page 14-306
Replacement, page 14-308
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст