Acura RSX Honda Integra. Manual — part 128
04
+
−
−
−
−
YES
NO
YES
NO
11-218
PGM-FI System
DTC Troubleshooting (cont’d)
ECM/PCM CONNECTOR A (31P)
AFS
(RED)
8. Check for continuity between ECM/PCM connector
terminal A6 and body ground.
Repair open in the wire between the A/F
sensor (Sensor 1) and the ECM/PCM (A16).
Repair open in the wire between the A/F
sensor (Sensor 1) and the ECM/PCM (A6).
9. Substitute a known-good A/F sensor (Sensor 1) and
recheck.
Update the ECM/PCM if it does not have the
latest software, or substitute a known-good ECM/
PCM (see page 11-6), then recheck. If the symptom/
indication goes away with a known-good ECM/PCM,
replace the original ECM/PCM (see page 11-284).
Replace the A/F sensor (Sensor 1) (see page
11-279).
Wire side of female terminals
Is ther e continuity?
Is DT C P1157 indicated?
05/06/27 17:37:51 61S6M040_110_0218
01
02
03
S6M6AALK72100091157FAAT00
−
+
+
−
+
−
−
−
−
DTC P1157:
YES
NO
YES
NO
11-219
A/F SENSOR (SENSOR 1) 4P CONNECTOR
AFS
(YEL/GRN)
JUMPER WIRE
AFS
(RED)
ECM/PCM CONNECTOR A (31P)
AFS
(RED)
AFS
(RED/YEL)
A/F SENSOR (SENSOR 1) 4P CONNECTOR
AFS
(RED)
JUMPER WIRE
A/F Sensor (Sensor 1) AFS Circuit
High Voltage
(2005-2006 models)
1. Turn the ignition switch ON (II).
2. Clear the DTC with the HDS.
3. Start the engine, and wait 20 seconds.
4. Check for Temporary DTCs or DTCs with the HDS.
Go to step 5.
Intermittent failure, system is OK at this time.
Check for poor connections or loose terminals at
the A/F sensor (Sensor 1) and the ECM/PCM.
5. Turn the ignition switch OFF.
6. Jump the SCS line with the HDS.
7. Disconnect the A/F sensor (Sensor 1) 4P connector.
8. Disconnect ECM/PCM connector A (31P).
9. Connect A/F sensor (Sensor 1) 4P connector
terminals No. 1 and No. 2 with a jumper wire.
10. Check for continuity between ECM/PCM connector
terminals A28 and A31.
Go to step 14.
Go to step 11.
11. Remove the jumper wire from the A/F sensor
(Sensor 1) 4P connector.
12. Connect A/F sensor (Sensor 1) 4P connector
terminal No. 1 to body ground with a jumper wire.
(cont’d)
Wire side of female terminals
Wire side of female terminals
Wire side of female terminals
Is DT C P1157 indicated?
Is ther e continuity?
05/06/27 17:37:52 61S6M040_110_0219
04
+
−
−
−
−
−
−
−
−
YES
NO
YES
NO
YES
NO
YES
NO
11-220
PGM-FI System
DTC Troubleshooting (cont’d)
AFS
(RED)
ECM/PCM CONNECTOR A (31P)
13. Check for continuity between ECM/PCM connector
terminal A31 and body ground.
Repair open in the wire between the ECM/
PCM (A28) and the A/F sensor (Sensor 1), then go
to step 15.
Repair open in the wire between the ECM/
PCM (A31) and the A/F sensor (Sensor 1), then go
to step 15.
14. Replace the A/F sensor (Sensor 1) (see page
11-279).
15. Reconnect all connectors.
16. Turn the ignition switch ON (II).
17. Reset the ECM/PCM with the HDS.
18. Do the ECM/PCM idle learn procedure (see page
11-349).
19. Check for Temporary DTCs or DTCs with the HDS.
If DTC P1157 is indicated, check for poor
connections or loose terminals at the A/F sensor
(Sensor 1) and the ECM/PCM. If the connector and
terminal fits are OK, go to step 21. If any other
Temporary DTCs or DTCs are indicated, go to the
indicated DTC’s troubleshooting.
Go to step 20.
20. Monitor the OBD STATUS for DTC P1157 in the
DTCs MENU with the HDS.
Troubleshooting is complete.
If the screen indicates FAILED, check for poor
connections or loose terminals at the A/F sensor
(Sensor 1) and the ECM/PCM, then go to step 1. If
the screen indicates NOT COMPLETED, go to
step 18 and recheck.
21. Update the ECM/PCM if it does not have the latest
software, or substitute a known-good ECM/PCM
(see page 11-6).
22. Check for Temporary DTCs or DTCs with the HDS.
Go to step 20 and recheck.
If the ECM/PCM was updated, troubleshooting
is complete. If the ECM/PCM was substituted,
replace the original ECM/PCM (see page 11-284).
Wire side of female terminals
Is ther e continuity?
Ar e any T empor ar y DT Cs or DT Cs indicated?
Does the scr een indicate PASSED?
Is DT C P1157 indicated?
05/06/27 17:37:52 61S6M040_110_0220
−
01
02
03
S6M6AAGK72100091162FAAT00
−
+
+
−
+
−
−
−
−
−
−
−
DTC P1162:
YES
NO
YES
NO
YES
NO
11-221
AFS
(RED/YEL)
LG1
(BRN/YEL)
ECM/PCM CONNECTOR A (31P)
AFS
(RED)
AFS
(RED)
AFS
(RED/YEL)
ECM/PCM CONNECTOR A (31P)
JUMPER WIRE
JUMPER WIRE
A/F SENSOR (SENSOR 1) 4P CONNECTOR
AFS
(RED)
AFS
(YEL/GRN)
A/F Sensor (Sensor 1) Circuit
Malfunction
(2002-2003 models)
1. Reset the ECM/PCM (see page 11-4).
2. Start the engine, and wait for at least 2 minutes.
Go to step 3.
Intermittent failure, system is OK at this time.
Check for poor connections or loose terminals at
the A/F sensor (Sensor 1) and the ECM/PCM.
3. Turn the ignition switch OFF.
4. Start the engine.
5. Measure voltage between ECM/PCM connector
terminals A6 and A24 and between A16 and A24.
Go to step 6.
Go to step 10.
6. Turn the ignition switch OFF.
7. Disconnect the A/F sensor (Sensor 1) 4P connector
and ECM/PCM connector A (31P).
8. Connect ECM/PCM connector terminals A6 and A16
to body ground with a jumper wire.
9. Check for continuity between A/F sensor (Sensor 1)
4P connector terminals No. 1, No. 2, and body
ground individually.
Replace the A/F sensor (Sensor 1) (see page
11-279).
Repair open in the wire between the A/F
sensor (Sensor 1) and the ECM/PCM (A6 or A16).
(cont’d)
Wire side of female terminals
Wire side of female terminals
Wire side of female terminals
Is DT C P1162 indicated?
Is ther e 2.5
3.0 V ?
Is ther e continuity?
05/06/27 17:37:52 61S6M040_110_0221
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст