RAM 2500 (2022 year). Manual in english — page 23
364
SERVICING AND MAINTENANCE
M
AINTENANCE
P
LAN
— G
ASOLINE
E
NGINE
Mileage or time passed
(whichever comes first)
20,000
30,000
40,000
50,000
60,000
70,000
80,000
90,000
100,000
110,000
120,000
130,000
140,000
150,000
Or Years:
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Or Kilometers:
32,000
48,000
64,000
80,000
96,000
112,000
128,000
144,000
160,000
176,000
192,000
208,000
224,000
240,000
Additional Inspections
Inspect the CV/Universal joints.
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Inspect front suspension, tie rod ends,
and replace if necessary.
X
X
X
X
X
X
X
Inspect the front and rear axle surfaces.
If gear oil leakage is suspected, check
the fluid level. If using your vehicle for
police, taxi, fleet, off-road or frequent
trailer towing, change axle fluid.
X
X
X
X
X
X
X
Inspect the brake linings, replace as
necessary.
X
X
X
X
X
X
X
Adjust parking brake as necessary.
X
X
X
X
X
X
X
Inspect transfer case fluid.
X
X
X
Additional Maintenance
Replace the cabin air filter.
To be replaced every 12,000 mi (19,000 km).
Replace the engine air cleaner filter.
X
X
X
X
X
-------------------------------------------------------------------------------------------------------------------------------------------------------------
SERVICING AND MAINTENANCE
365
Replace spark plugs.
1
X
Flush and replace the engine coolant at
10 years or 150,000 miles (240,000 km)
whichever comes first.
X
X
Inspect the transfer case fluid, change for
any of the following: police, taxi, fleet, or
frequent trailer towing.
X
X
Change the transfer case fluid.
X
Inspect and replace PCV valve if
necessary.
X
1. The spark plug change interval is mileage based only, yearly intervals do not apply.
Mileage or time passed
(whichever comes first)
20,000
30,000
40,000
50,000
60,000
70,000
80,000
90,000
100,000
110,000
120,000
130,000
140,000
150,000
Or Years:
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Or Kilometers:
32,000
48,000
64,000
80,000
96,000
112,000
128,000
144,000
160,000
176,000
192,000
208,000
224,000
240,000
WARNING!
You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have
any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
Failure to properly inspect and maintain your vehicle could result in a component malfunction and affect vehicle handling and performance. This could cause
an accident.
8
-------------------------------------------------------------------------------------------------------------------------------------------------------------
366
SERVICING AND MAINTENANCE
M
AINTENANCE
P
LAN
— D
IESEL
E
NGINE
Mileage or time passed
(whichever comes first):
7,
500
15,000
22,500
30,000
37,500
45,000
52,500
60,000
67,500
75,000
82,500
90,000
97,500
105,000
112,500
120,000
127,500
135,000
142,500
150,000
Or Months:
6
12 18 24 30 36 42 48 54 60 66 72 78 84 90 96 102 108 114 120
Or Kilometers:
12,000
24,000
36,000
48,000
60,000
72,000
84,000
96,000
108,000
120,000
132,000
144,000
156,000
168,000
180,000
192,000
204,000
216,000
228,000
240,000
Change engine oil every 15,000 miles
(24,000 km) or 12 months or 500 Hours or
sooner if prompted by the oil change indicator
system, whichever comes first.
1
X
X
X
X
X
X
X
X
X
X
Additional Inspections
Check the Diesel Exhaust Fluid (DEF) tank,
refill if necessary.
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Rotate the tires.
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Inspect front end, and lubricate — If equipped
with serviceable fittings.
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Inspect engine air cleaner filter, replace if
necessary.
2
X
X
X
X
X
X
X
X
X
X
Inspect the CV/Universal joints.
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
-------------------------------------------------------------------------------------------------------------------------------------------------------------
SERVICING AND MAINTENANCE
367
Inspect the front suspension, tie rod ends and
boot seals for cracks or leaks and all parts for
damage, wear, improper looseness or end
play; replace if necessary.
X
X
X
X
X
X
X
X
X
X
Inspect the brake linings.
X
X
X
X
X
X
Inspect and adjust parking brake.
X
X
X
X
X
X
Inspect drive belt; replace as necessary.
X
X
X
X
X
X
Inspect wheel bearings.
X
X
X
X
X
Additional Maintenance
Replace the cabin air filter.
To be replaced every 12,000 mi (19,000 km).
Replace the engine fuel filter.
X
X
X
X
X
X
X
X
X
X
Replace the chassis mounted fuel filter.
X
X
X
X
X
X
X
X
X
X
Inspect the front and rear axle surfaces. If
gear oil leakage is suspected, check the fluid
level. If using your vehicle for police, taxi, fleet,
off-road or frequent trailer towing change the
axle fluid.
X
X
X
X
X
X
Mileage or time passed
(whichever comes first):
7,
500
15,000
22,500
30,000
37,500
45,000
52,500
60,000
67,500
75,000
82,500
90,000
97,500
105,000
112,500
120,000
127,500
135,000
142,500
150,000
Or Months:
6
12 18 24 30 36 42 48 54 60 66 72 78 84 90 96 102 108 114 120
Or Kilometers:
12,000
24,000
36,000
48,000
60,000
72,000
84,000
96,000
108,000
120,000
132,000
144,000
156,000
168,000
180,000
192,000
204,000
216,000
228,000
240,000
8
-------------------------------------------------------------------------------------------------------------------------------------------------------------
368
SERVICING AND MAINTENANCE
Inspect the transfer case fluid (4x4), change
for any of the following: police, taxi, fleet, or
frequent trailer towing.
X
X
X
X
X
Change the transfer case fluid (4x4).
X
X
Change automatic transmission fluid
(AS69RC transmission only).
X
X
X
X
Change automatic transmission fluid and
sump filter (AS69RC transmission only).
X
X
Change automatic transmission fluid and
filter(s) if using your vehicle for any of the
following: police, fleet, or frequent trailer
towing (68RFE transmission only).
X
X
Change automatic transmission fluid and
filter(s).
X
Replace Crankcase Ventilation Filter (CCV).
X
X
Mileage or time passed
(whichever comes first):
7,
500
15,000
22,500
30,000
37,500
45,000
52,500
60,000
67,500
75,000
82,500
90,000
97,500
105,000
112,500
120,000
127,500
135,000
142,500
150,000
Or Months:
6
12 18 24 30 36 42 48 54 60 66 72 78 84 90 96 102 108 114 120
Or Kilometers:
12,000
24,000
36,000
48,000
60,000
72,000
84,000
96,000
108,000
120,000
132,000
144,000
156,000
168,000
180,000
192,000
204,000
216,000
228,000
240,000
-------------------------------------------------------------------------------------------------------------------------------------------------------------
SERVICING AND MAINTENANCE
369
Flush and replace power steering fluid.
X
Flush and replace engine coolant. ***
X
1. Under no circumstances should oil change intervals exceed 15,000 miles (24,000 km) or 12 months or 500 Hours, whichever comes first.
2. Under no circumstances should the engine air cleaner filter exceed 30,000 miles (48,000 km) or 24 months, whichever comes first.
Mileage or time passed
(whichever comes first):
7,
500
15,000
22,500
30,000
37,500
45,000
52,500
60,000
67,500
75,000
82,500
90,000
97,500
105,000
112,500
120,000
127,500
135,000
142,500
150,000
Or Months:
6
12 18 24 30 36 42 48 54 60 66 72 78 84 90 96 102 108 114 120
Or Kilometers:
12,000
24,000
36,000
48,000
60,000
72,000
84,000
96,000
108,000
120,000
132,000
144,000
156,000
168,000
180,000
192,000
204,000
216,000
228,000
240,000
WARNING!
You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have
any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
Failure to properly inspect and maintain your vehicle could result in a component malfunction and affect vehicle handling and performance. This could cause
an accident.
CAUTION!
***The manufacturer highly recommends that all cooling system service, maintenance, and repairs be performed by your local authorized dealer.
8
-------------------------------------------------------------------------------------------------------------------------------------------------------------
370
SERVICING AND MAINTENANCE
ENGINE COMPARTMENT
6.4L G
ASOLINE
E
NGINE
1 — Engine Coolant Pressure Cap
6 — Engine Air Cleaner Filter
2 — Engine Oil Fill
7 — Power Steering Reservoir Cap
3 — Engine Oil Dipstick
8 — Power Distribution Center (Fuses)
4 — Brake Fluid Reservoir Cap
9 — Washer Fluid Reservoir Cap
5 — Battery
-------------------------------------------------------------------------------------------------------------------------------------------------------------
SERVICING AND MAINTENANCE
371
6.7L D
IESEL
E
NGINE
— 6-S
PEED
68RFE
1 — Battery
7 — Brake Fluid Reservoir Cap
2 — Engine Coolant Pressure Reservoir
8 — Battery
3 — Engine Coolant Reservoir Cap
9 — Engine Air Cleaner Filter
4 — Automatic Transmission Dipstick
10 — Power Steering Reservoir Cap
5 — Engine Oil Fill
11 — Washer Fluid Reservoir Cap
6 — Engine Oil Dipstick
12 — Power Distribution Center (Fuses)
8
-------------------------------------------------------------------------------------------------------------------------------------------------------------
372
SERVICING AND MAINTENANCE
6.7L D
IESEL
E
NGINE
— 6-S
PEED
AS69RC HD
1 — Battery
7 — Brake Fluid Reservoir Cap
2 — Engine Coolant Pressure Cap
8 — Battery
3 — Engine Coolant Pressure Reservoir
9 — Power Distribution Center (Fuses)
4 — Engine Oil Fill
10 — Engine Air Cleaner Filter
5 — Engine Oil Dipstick
11 — Power Steering Reservoir Cap
6 — Automatic Transmission Dipstick
12 — Washer Fluid Reservoir Cap
-------------------------------------------------------------------------------------------------------------------------------------------------------------
SERVICING AND MAINTENANCE
373
C
HECKING
O
IL
L
EVEL
To ensure proper engine lubrication, the engine oil
must be maintained at the correct level. Check the
oil level at regular intervals, such as every fuel
stop. The best time to check the engine oil level is
about five minutes after a fully warmed up engine
is shut off.
Checking the oil while the vehicle is on level ground
will improve the accuracy of the oil level readings.
There are four possible dipstick types:
Crosshatched zone.
Crosshatched zone marked SAFE.
Crosshatched zone marked with MIN at the low
end of the range and MAX at the high end of the
range.
Crosshatched zone marked with dimples at the
MIN and the MAX ends of the range.
NOTE:
Always maintain the oil level within the crosshatch
markings on the dipstick.
Adding 1 quart (1 liter) of oil when the reading is at
the low end of the dipstick range will raise the oil
level to the high end of the range marking.
A
DDING
W
ASHER
F
LUID
The fluid reservoir is located under the hood and
should be checked for fluid level at regular
intervals. Fill the reservoir with windshield washer
solvent only (not radiator antifreeze). When
refilling the washer fluid reservoir, take some
washer fluid and apply it to a cloth or towel and
wipe the wiper blades clean. This will help blade
performance.
To prevent freeze-up of your windshield washer
system in cold weather, select a solution or mixture
that meets or exceeds the temperature range of
your climate. This rating information can be found
on most washer fluid containers.
After the engine has warmed up, operate the
defroster for a few minutes to reduce the
possibility of smearing or freezing the fluid on the
cold windshield. Windshield washer solution used
with water as directed on the container, aids
cleaning action, reduces the freezing point to avoid
line clogging, and is not harmful to paint or trim.
M
AINTENANCE
-F
REE
B
ATTERY
Your vehicle is equipped with a maintenance-free
battery. You will never have to add water, and
periodic maintenance is not required.
CAUTION!
Overfilling or underfilling the crankcase will
cause oil aeration or loss of oil pressure. This
could damage your engine.
WARNING!
Commercially available windshield washer
solvents are flammable. They could ignite and
burn you. Care must be exercised when filling or
working around the washer solution.
WARNING!
Battery fluid is a corrosive acid solution and
can burn or even blind you. Do not allow
battery fluid to contact your eyes, skin, or
clothing. Do not lean over a battery when
attaching clamps. If acid splashes in eyes or
on skin, flush the area immediately with large
Battery gas is flammable and explosive. Keep
flame or sparks away from the battery. Do not
use a booster battery or any other booster
source with an output greater than 12 Volts.
Do not allow cable clamps to touch each
other.
Battery posts, terminals, and related accesso
-
ries contain lead and lead compounds. Wash
hands after handling.
8
-------------------------------------------------------------------------------------------------------------------------------------------------------------
374
SERVICING AND MAINTENANCE
P
RESSURE
W
ASHING
Cleaning the engine compartment with a high
pressure washer is not recommended.
VEHICLE MAINTENANCE
An authorized dealer has the qualified service
personnel, special tools, and equipment to
perform all service operations in an expert
manner. Service Manuals are available which
include detailed service information for your
vehicle. Refer to these Service Manuals before
attempting any procedure yourself.
NOTE:
Intentional tampering with emissions control
systems may void your warranty and could result in
civil penalties being assessed against you.
E
NGINE
O
IL
Engine Oil Selection — Gasoline Engine
Use only the manufacturer's recommended fluid
NOTE:
Hemi engines (6.4L) at times can tick right after
startup and then quiet down after approximately
30 seconds. This is normal and will not harm the
engine. This characteristic can be caused by short
drive cycles. For example, if the vehicle is started
then shut off after driving a short distance. Upon
restarting, you may experience a ticking sound.
Other causes could be if the vehicle is unused for an
extended period of time, incorrect oil, extended oil
changes or extended idling. If the engine continues
to tick or if the Malfunction Indicator Light (MIL)
comes on, see the nearest authorized dealer.
Engine Oil Selection — Diesel Engine
Use only the manufacturer's recommended fluid
CAUTION!
It is essential when replacing the cables on
the battery that the positive cable is attached
to the positive post and the negative cable is
attached to the negative post. Battery posts
are marked positive (+) and negative (-) and
are identified on the battery case. Cable
clamps should be tight on the terminal posts
and free of corrosion.
If a “fast charger” is used while the battery is
in the vehicle, disconnect both vehicle battery
cables before connecting the charger to the
battery. Do not use a “fast charger” to provide
starting voltage.
CAUTION!
Precautions have been taken to safeguard all
parts and connections however, the pressure
generated by these machines is such that
complete protection against water ingress
cannot be guaranteed.
WARNING!
You can be badly injured working on or around a
motor vehicle. Only do service work for which
you have the knowledge and the proper equip
-
ment. If you have any doubt about your ability to
perform a service job, take your vehicle to a
competent mechanic.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
SERVICING AND MAINTENANCE
375
American Petroleum Institute (API)
Approved Engine Oil
These symbols mean that the oil has been certified
by the API. The manufacturer only recommends API
trademark oils.
The API Starburst trademark certifies
0W-20, 0W-30 and 5W-30 engine oils.
The API Donut trademark certifies 0W-40
and 5W-40 engine oil.
For diesel engines, oils with a high ash content may
produce damaging deposits on cylinder head
valves and/or after treatment system damage. A
maximum sulfated ash content of 1.00 mass % is
recommended for all oil used in the engine.
The same oil change interval is to be followed for
synthetic oil as for petroleum-based oil. Also,
synthetic oil must meet the same performance
specifications as petroleum oil.
Synthetic Engine Oils
Your engine was designed for synthetic engine oils,
only use synthetic API approved engine oils.
Synthetic engine oils which do not have both the
correct API trademark and the correct SAE viscosity
grade numbers should not be used.
Materials Added To Engine Oil
The manufacturer strongly recommends against
the addition of any additives (other than leak
detection dyes) to the engine oil. Engine oil is an
engineered product and its performance may be
impaired by supplemental additives.
Disposing Of Used Engine Oil And Oil
Filters
Care should be taken in disposing of used engine
oil and oil filters from your vehicle. Used oil and oil
filters, indiscriminately discarded, can present a
problem to the environment. Contact an
authorized dealer, service station or governmental
agency for advice on how and where used oil and
oil filters can be safely discarded in your area.
E
NGINE
O
IL
F
ILTER
The engine oil filter should be replaced with a new
filter at every engine oil change.
Engine Oil Filter Selection
A full-flow type disposable oil filter should be used
for replacement. The quality of replacement filters
varies considerably. Only high quality Mopar®
certified filters should be used.
E
NGINE
A
IR
C
LEANER
F
ILTER
For the proper maintenance intervals
Engine Air Cleaner Filter Selection
The quality of replacement engine air cleaner
filters varies considerably. Only high quality filters
should be used to ensure most efficient service.
Mopar® engine air cleaners are a high quality filter
and are recommended.
CAUTION!
Do not use chemical flushes in your engine oil as
the chemicals can damage your engine. Such
damage is not covered by the New Vehicle
Limited Warranty.
WARNING!
The air induction system (air cleaner, hoses,
etc.) can provide a measure of protection in the
case of engine backfire. Do not remove the air
induction system (air cleaner, hoses, etc.) unless
such removal is necessary for repair or
maintenance. Make sure that no one is near the
engine compartment before starting the vehicle
with the air induction system (air cleaner, hoses,
etc.) removed. Failure to do so can result in
serious personal injury.
8
-------------------------------------------------------------------------------------------------------------------------------------------------------------
376
SERVICING AND MAINTENANCE
Engine Air Cleaner Filter Inspection And
Replacement — Gasoline Engine
Inspect engine air cleaner filter for dirt and or
debris, if you find evidence of either dirt or debris
you should change your engine air cleaner filter.
NOTE:
When replacing the engine air cleaner filter on
vehicles equipped with a 6.4L gasoline engine,
replace with a dry (non-oiled) filter only.
Engine Air Cleaner Filter Removal
1. With suitable tool fully loosen (six) fasteners
on engine air cleaner filter.
Engine Air Cleaner Filter
2. Lift the engine air cleaner filter cover to access
the engine air cleaner filter.
3. Remove the engine air cleaner filter from the
housing assembly.
Engine Air Cleaner Filter Assembly
Engine Air Cleaner Filter Installation
NOTE:
Inspect and clean the housing if dirt or debris is
present before replacing the engine air cleaner
filter.
1. Install the engine air cleaner filter into the
housing assembly with the engine air cleaner
filter inspection surface facing downward.
2. Install the engine air cleaner filter cover onto
the housing assembly.
3. Tighten the fasteners (six) on the engine air
cleaner filter assembly.
Engine Air Cleaner Filter Inspection and
Replacement — Diesel Engine
Inspect engine air cleaner filter for dirt and or
debris, if you find evidence of either dirt or debris
you should change your engine air cleaner filter.
Engine Air Cleaner Filter Removal
1. Remove the screws from the engine air
cleaner filter cover.
Engine Air Cleaner Filter Cover
1 — Fasteners
2 — Air Hose Clamp
3 — Engine Air Cleaner Filter Cover
1 — Engine Air Cleaner Filter Cover
2 — Engine Air Cleaner Filter
1 — Engine Air Cleaner Filter Cover
2 — Screws
-------------------------------------------------------------------------------------------------------------------------------------------------------------
SERVICING AND MAINTENANCE
377
(Continued)
2. Lift the engine air cleaner filter cover to access
the engine air cleaner filter.
3. Remove the engine air cleaner filter from the
housing assembly.
Engine Air Cleaner Filter
Engine Air Cleaner Filter Installation
NOTE:
Inspect and clean the housing if dirt or debris is
present before replacing the engine air cleaner
filter.
1. Install the engine air cleaner into the housing
assembly with the engine air cleaner filter
inspection surface facing downward.
2. Install the engine air cleaner filter cover onto
the housing assembly locating tabs.
3. Tighten (6) screws to secure the engine air
cleaner filter cover to the housing assembly.
A
IR
C
ONDITIONER
M
AINTENANCE
For best possible performance, your air conditioner
should be checked and serviced by an authorized
dealer at the start of each warm season. This
service should include cleaning of the condenser
fins and a performance test. Drive belt tension
should also be checked at this time.
Refrigerant Recovery And Recycling —
R-134a (If Equipped)
R-134a Air Conditioning Refrigerant is a Hydrofluo
-
rocarbon (HFC) that is an ozone-friendly
substance. The manufacturer recommends that
air conditioning service be performed by an
authorized dealer or other service facilities using
recovery and recycling equipment.
NOTE:
Use only manufacturer approved A/C system PAG
compressor oil and refrigerants.
1 — Engine Air Cleaner Filter
2 — Engine Air Cleaner Filter Inspection Surface
WARNING!
Use only refrigerants and compressor lubri
-
cants approved by the manufacturer for your
air conditioning system. Some unapproved
refrigerants are flammable and can explode,
injuring you. Other unapproved refrigerants or
lubricants can cause the system to fail,
requiring costly repairs. Refer to Warranty
Information Book, for further warranty infor
-
mation.
The air conditioning system contains refrig
-
erant under high pressure. To avoid risk of
personal injury or damage to the system,
adding refrigerant or any repair requiring lines
to be disconnected should be done by an
experienced technician.
CAUTION!
Do not use chemical flushes in your air
conditioning system as the chemicals can
damage your air conditioning components. Such
damage is not covered by the New Vehicle
Limited Warranty.
WARNING!
8
-------------------------------------------------------------------------------------------------------------------------------------------------------------
378
SERVICING AND MAINTENANCE
Refrigerant Recovery And Recycling —
R-1234yf (If Equipped)
R–1234yf Air Conditioning Refrigerant is a
Hydrofluoroolefin (HFO) that is endorsed by the
Environmental Protection Agency and is an
ozone-friendly substance with a low
global-warming potential. The manufacturer
recommends that air conditioning service be
performed by an authorized dealer using recovery
and recycling equipment.
NOTE:
Use only manufacturer approved A/C system PAG
compressor oil, and refrigerants.
Cabin Air Filter Replacement
For the proper maintenance intervals
The cabin air filter is located in the fresh air inlet
behind the glove compartment. Perform the
following procedure to replace the filter:
1. Open the glove compartment and remove all
contents.
2. With the glove compartment door open,
remove the glove compartment tension tether
and tether clip by sliding the clip toward the
face of the glove compartment door. Lift the
clip out of glove compartment door and
release into dash panel.
Right Side Of Glove Compartment
3. There are travel stops on both sides of the
glove compartment. Push inward on right side
of the glove compartment travel stop to
disengage the stop. Then pull the right of the
glove compartment outward (away from the
hinge) to disengage the right side of the
compartment from the hinge. Continue by
removing the left side from the hinge by slightly
lowering the compartment while pulling
outward until it is completely disengaged from
the hinge.
Glove Compartment
WARNING!
Do not remove the cabin air filter while the
vehicle is running, or while the ignition is in the
ACC or ON/RUN mode. With the cabin air filter
removed and the blower operating, the blower
can contact hands and may propel dirt and
debris into your eyes, resulting in personal injury.
1 — Glove Compartment Door
2 — Glove Compartment Tension Tether
1 — Glove Compartment Travel Stop
2 — Glove Compartment Tension Tether
3 — Glove Compartment Door
-------------------------------------------------------------------------------------------------------------------------------------------------------------
SERVICING AND MAINTENANCE
379
4. Remove the filter cover by pushing in on the
finger tabs on each end of the filter cover.
Filter Cover
Filter Cover Removal
5. Remove the cabin air filter by pulling it straight
out of the housing.
Cabin Air Filter
6. Install the cabin air filter with the arrow on the
filter pointing toward the floor. When installing
the filter cover, press on each end until you
hear an audible click.
7. Reinstall the glove compartment on the
hinges.
8. Pull the tension tether outward and reinstall
the glove compartment past the travel stops by
pushing in on the glove compartment sides.
Right Side Of Glove Compartment
NOTE:
Ensure the glove compartment door hinges and
glove compartment travel stops are fully engaged.
9. Reattach the glove compartment tension
tether by inserting the tether clip in the glove
compartment and sliding the clip away from
the face of the glove compartment door.
1 — Finger Tabs
CAUTION!
The cabin air filter is identified with an arrow to
indicate airflow direction through the filter.
Failure to properly install the filter will result in
the need to replace it more often.
1 — Glove Compartment Travel Stop
2 — Glove Compartment Tension Tether
3 — Glove Compartment Door
8
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст