RAM 1500 TRX (2022 year). Manual in english — page 6
GETTING TO KNOW YOUR VEHICLE
93
Bed Step Components (Standard Tailgate)
Bed Step Extended
NOTE:
Once the spring load is overcome, the bed step will
extend out quickly, so be sure to stand in a position
that will avoid coming into contact with the step as
it extends.
To stow the bed step back under the tailgate, push
the bed step forward with your foot until the bed
step is retracted by the spring load.
Bed Step For Multifunction Tailgate
Bed Step Location
To extend the bed step, place your foot on the top
center of the bed step, and push down while
pulling rearward. A small amount of force will
release the spring load and extend the bed step
out and away from the tailgate.
Bed Step Extended
1 — Bed Step
2 — Foot Tab
WARNING!
Do not attempt to stow the bed step with your
hands. The low clearance space between the
bed step and the rear bumper as the bed step
returns to the stowed position could result in
injury to your hands or fingers.
2
-------------------------------------------------------------------------------------------------------------------------------------------------------------
94
GETTING TO KNOW YOUR VEHICLE
(Continued)
NOTE:
Once the spring load is overcome, the bed step will
extend out quickly. Be sure to stand in a position
that will avoid coming into contact with the step as
it extends.
To stow the bed step back under the tailgate, push
the bed step forward with your foot until the bed
step is retracted by the spring load.
PICKUP BOX
The pickup box has many features designed for
utility and convenience.
Pickup Box Features
NOTE:
If you are installing a Toolbox, Ladder Rack or
Headache Rack at the front of the Pickup Box, you
must use Mopar® Box Reinforcement Brackets
that are available from an authorized dealer.
You can carry wide building materials (sheets of
plywood, etc.) by building a raised load floor.
Place lumber across the box in the indentations
provided above the wheel housings and in the
bulkhead dividers to form the floor.
WARNING!
Do not attempt to stow the bed step with your
hands. The low clearance space between the
bed step and the rear bumper as the bed step
returns to the stowed position could result in
injury to your hands or fingers.
1 — Upper Load Floor Indents
2 — Bulk Head Dividers
3 — Cleats
WARNING!
The pickup box is intended for load carrying
purposes only, not for passengers, who should
sit in seats and use seat belts.
Care should always be exercised when oper
-
ating a vehicle with unrestrained cargo.
Vehicle speeds may need to be reduced.
Severe turns or rough roads may cause
shifting or bouncing of the cargo that may
result in vehicle damage. If wide building
materials are to be frequently carried, the
installation of a support is recommended. This
will restrain the cargo and transfer the load to
the pickup box floor.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
GETTING TO KNOW YOUR VEHICLE
95
There are stampings in the sheet metal on the
inner side bulkheads of the box in front of and
behind both wheel housings. Place wooden boards
across the box from side to side to create separate
load compartments in the pickup box.
There are four tie-down cleats bolted to the lower
sides of the pickup box that can sustain loads up
to 1,000 lb (450 kg) total.
B
ED
R
AIL
T
IE
-D
OWN
S
YSTEM
—
I
F
E
QUIPPED
There are two adjustable cleats on each side of the
bed that can be used to assist in securing cargo.
Adjustable Cleats
Each cleat must be located and tightened down in
one of the detents, along either rail, in order to
keep cargo properly secure.
To move the cleat to any position on the rail, turn
the nut counterclockwise, approximately three
turns. Then pull out on the cleat and slide it to the
detent nearest the desired location. Make sure the
cleat is seated in the detent and tighten the nut.
Adjustable Cleat Assembly
If you wish to carry more than 600 lb (272 kg)
of material suspended above the wheelhouse,
supports must be installed to transfer the
weight of the load to the pickup box floor or
vehicle damage may result. The use of proper
supports will permit loading up to the rated
payload.
Unrestrained cargo may be thrown forward in
an accident causing serious or fatal injury.
WARNING!
CAUTION!
The maximum load per cleat should not exceed
250 lb (113 kg), or 500 lb (227 kg) total per rail,
and the angle of the load on each cleat should
not exceed 45 degrees above horizontal, or
damage to the cleat or cleat rail may occur.
1 — Utility Rail Detent
2 — Cleat Retainer Nut
3 — Utility Rail Cleat
2
-------------------------------------------------------------------------------------------------------------------------------------------------------------
96
GETTING TO KNOW YOUR VEHICLE
Cleat Removal (Standard Box Rail)
To remove the cleats from the utility rail, slide the
cleat forward to access the cut out at the end of the
box rail, then remove the cleat.
Slide Cleat Forward To Remove
Cleat Removal (With Tonneau Cover)
To remove the cleats from the utility rail, remove
the end cap screw located in the center of the end
cap, using a #T30 Torx head driver. Remove the
end cap and slide the cleat off the end of the rail.
End Cap Screw Location With Tonneau Cover
Cleat Removal (Without Tonneau Cover)
Remove the end cap by pushing upward on the
release button located beneath the end cap while
pulling the cap away from the rail. The cleat can
now be removed by sliding it off the end of the rail.
End Cap Release Button Without Tonneau Cover
Pull End Cap Away From Rail
RAMBOX — IF EQUIPPED
The RamBox system is an integrated pickup box
storage and cargo management system consisting
of three features:
Cargo storage bins
Cargo divider
NOTE:
Bed rail tie-down system is also available for
vehicles not equipped with a RamBox.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
GETTING TO KNOW YOUR VEHICLE
97
L
OCKING
A
ND
U
NLOCKING
R
AM
B
OX
Push and release the lock or unlock button on the
key fob to lock and unlock all doors, the tailgate
page 19. To unlatch the
storage bin manually, insert the emergency key
into the keyhole and turn clockwise. Always return
the key to the upright (vertical) position before
removing it from the keyhole.
R
AM
B
OX
C
ARGO
S
TORAGE
B
INS
Cargo storage bins are located on both sides of the
pickup box. The cargo storage bins provide
watertight, lockable, illuminated storage for up to
150 lb (68 kg) of evenly distributed cargo.
RamBox Cargo Storage Bins
To open a storage bin with the RamBox unlocked,
push and release the button located on the lid. The
RamBox lid will open upward to allow hand access.
Lift the lid to fully open.
NOTE:
RamBox will not open when the button is pushed if
the RamBox is locked.
RamBox Button And Keyhole Lock
CAUTION!
Ensure cargo bin lids are closed and latched
before moving or driving vehicle.
Loads applied to the top of the bin lid should
be minimized to prevent damage to the lid and
latching/hinging mechanisms.
Damage to the RamBox bin may occur due to
heavy/sharp objects placed in bin that shift
due to vehicle motion. In order to minimize
potential for damage, secure all cargo to
prevent movement and protect inside
surfaces of bin from heavy/sharp objects with
appropriate padding.
CAUTION!
Failure to follow the following items could cause
damage to the vehicle:
Assure that all cargo inside the storage bins is
properly secured.
Do not exceed cargo weight rating of 150 lb
(68 kg) per bin.
1 — Keyhole Lock
2 — Button
2
-------------------------------------------------------------------------------------------------------------------------------------------------------------
98
GETTING TO KNOW YOUR VEHICLE
The interior of the RamBox will automatically
illuminate when the lid is opened. The timing can
be adjusted within Uconnect Settings
Cargo bins feature two removable drain plugs
(to allow water to drain from bins). To remove plug,
pull up on the edge. To install, push plug downward
into drain hole.
RamBox Drain Plug Removal
NOTE:
Provisions are provided in the bins for cargo
dividers. These accessories (in addition to other
RamBox accessories) are available from Mopar®.
If equipped, a 115 Volt (400 Watts maximum)
inverter may be located inside the RamBox of your
vehicle. The inverter can be turned on by the
Instrument Panel Power Inverter switch located to
the left of the steering wheel. The RamBox inverter
can power cellular phones, electronics and
other low power devices requiring power up to
400 Watts. Certain video game consoles exceed
this power limit, as will most power tools.
RamBox Power Inverter
The Instrument Panel Power Inverter switch is only
found on vehicles equipped with a RamBox. The
switch only controls on/off operation of the power
outlet in the RamBox; it does not control on/off
operation of the power outlets located inside the
cabin of the vehicle.
Instrument Panel Power Inverter Switch
CAUTION!
Leaving the lid open for extended periods of time
could cause the vehicle battery to discharge. If
the lid is required to stay open for extended
periods of time, it is recommended that the bin
lights be turned off manually using the on/off
switch.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
GETTING TO KNOW YOUR VEHICLE
99
R
AM
B
OX
S
AFETY
W
ARNING
Carefully follow these warnings to help prevent
personal injury or damage to your vehicle:
RamBox Emergency Release Lever
As a security measure, an Emergency Release
Lever is built into the storage bin cover latching
mechanism.
In the event of an individual being locked inside
the storage bin, the storage bin cover can be
opened from inside of the bin by pulling on the
glow-in-the-dark lever attached to the storage bin
cover latching mechanism.
Emergency Release Lever
B
ED
D
IVIDER
— I
F
E
QUIPPED
The bed divider has two functional positions:
Divider Position
Storage Position
Divider Position
The divider position is intended for managing your
cargo and assisting in keeping cargo from moving
around the bed. There are 11 divider slots along
the bed inner panels which allow for various
positions to assist in managing your cargo.
To install the bed divider into a divider position,
perform the following:
1. Make sure the center handle is unlocked
using the vehicle key and rotate the center
handle vertically to release the divider side
gates.
Center Handle And Lock
WARNING!
Always close the storage bin covers when your
vehicle is unattended.
Do not allow children to have access to the
storage bins. Once in the storage bin, young
children may not be able to escape. If trapped
in the storage bin, children can die from suffo
-
cation or heat stroke.
In an accident, serious injury could result if the
storage bin covers are not properly latched.
Do not drive the vehicle with the storage bin
covers open.
Keep the storage bin covers closed and
latched while the vehicle is in motion.
Do not use a storage bin latch as a tie-down.
1 — Center Handle Lock
2 — Handle
3 — Unlocked Position
4 — Locked Position
2
-------------------------------------------------------------------------------------------------------------------------------------------------------------
100
GETTING TO KNOW YOUR VEHICLE
2. With the side gates open, position the divider
so the outboard ends align with the intended
slots in the sides of the bed.
Aligning Gate To Slots
3. Rotate the side gates closed so that the
outboard ends are secured into the intended
slots of the bed.
4. Rotate the center handle horizontally to secure
the side gates in the closed position.
Side Gates Closed
5. Lock the center handle to secure the panel
into place.
Storage Position
The storage position for the bed divider is at the
front of the truck bed which maximizes the bed
cargo area when not in use.
To install the bed divider into the storage position,
perform the same steps as you would for the
divider position, except position the divider fully
forward in the bed against the front panel.
Storage Position
The outboard ends should be positioned in front of
the cargo tie-down loops.
Cargo Tie-Down Loop
-------------------------------------------------------------------------------------------------------------------------------------------------------------
GETTING TO KNOW YOUR VEHICLE
101
TRI-FOLD TONNEAU COVER — IF EQUIPPED
The Tri-Fold Tonneau Cover can be installed on the
truck bed to protect your gear and cargo.
T
ONNEAU
C
OVER
C
OMPONENTS
Folded Tonneau Cover Components
Tonneau Cover Latch Components
Position One
(Front Latches Latched And Stowage Straps Secured)
Position Two (Front And Rear Latches Latched)
1 — Stowage Strap
2 — Tonneau Cover Bumper Folded
1 — Handle
2 — Slide Locking Lever
3 — Locating Bumper
4 — Truck Flange Bead
5 — Latch Bumper
6 — J Hook
1 — Panel 1
2 — Panel 2
3 — Panel 3
2
-------------------------------------------------------------------------------------------------------------------------------------------------------------
102
GETTING TO KNOW YOUR VEHICLE
T
RI
-F
OLD
T
ONNEAU
C
OVER
F
OLDING
F
OR
D
RIVING
O
R
R
EMOVAL
To remove the Tonneau Cover use the
following steps:
1. Open the tailgate to access the rear pair of
Tonneau Cover latches located on the
underside of the Cover.
Location Of Rear Latches
Slide Locking Lever Inward
2. Slide the locking lever toward the inside of the
truck bed to release the J Hook and pull the
handle downward into the released position.
Unlatching Latch
Released Position
Hold The Bumper And Push The Handle Up
-------------------------------------------------------------------------------------------------------------------------------------------------------------
GETTING TO KNOW YOUR VEHICLE
103
3. Holding the bumper, push the fully released
latch to the center and push up. Push the
handle firmly, locking it into the stowed
position. Repeat Steps 2 and 3 for the
opposite side latch.
Stowed Position
Lift Panel 3 And Fold Onto Panel 2
4. Lift up on Panel 3 and fold it onto Panel 2.
Correct Folding — Hold Panels Together
NOTE:
When folding the second and third panels, the
sections MUST be held together to avoid damage
to the cover material. Fold the panel gently. Do not
allow the panels to drop under their own weight.
Incorrect Folding — Will Cause Damage
5. Lift up on the second and third panel and fold
them onto the first panel.
Stowage Strap Clipped
6. Unsnap the stowage strap and clip. Repeat for
both straps to prevent the Tonneau Cover
panels from unfolding.
Position One
(Front Latches Latched And Stowage Straps Secured)
2
-------------------------------------------------------------------------------------------------------------------------------------------------------------
104
GETTING TO KNOW YOUR VEHICLE
NOTE:
Be sure the Tonneau Cover has been folded
completely, and the stowage straps are engaged,
before removing.
Fully Folded Tonneau Cover
NOTE:
The vehicle can be driven with the Tonneau Cover
in the folded position or can be completely
removed.
Slide Locking Lever Inward
7. Slide the locking lever toward the inside of the
truck bed to release the J Hook and pull the
handle downward into the released position.
Unlatching Latch
Released Position
Hold The Bumper And Push The Handle Up
CAUTION!
The folded Tonneau Cover must be latched by
both front latches and both front stowage straps
or damage to the Tonneau Cover or vehicle may
occur while driving.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
GETTING TO KNOW YOUR VEHICLE
105
8. Holding the bumper, push the fully released
latch to the center and push up. Push the
handle firmly, locking it into the stowed
position. Repeat Steps 2 & 3 for the opposite
side latch.
9. With two people, remove the cover.
T
RI
-F
OLD
T
ONNEAU
C
OVER
I
NSTALLATION
To install the Tonneau Cover follow these steps:
1. Position the Tonneau Cover on the truck bed
and center using the locating bumpers.
2. Locate the front pair of Tonneau Cover latches
on the underside of the Cover. Slide the
locking lever toward the inside of the truck bed
and release the latch from the stowed
position, and pull the handle downward into
the released position. Do this for both the left
and right side.
Location of Front Latches
Slide Locking Lever Towards Inside Of Truck
Unlatching Latch
Released Position
2
-------------------------------------------------------------------------------------------------------------------------------------------------------------
106
GETTING TO KNOW YOUR VEHICLE
3. Swing the J Hook from the handle and push
the handle to the center and up, ensuring that
the J Hook is under the truck flange. Push up
on the handle firmly, locking it into the latched
position.
J Hook Under Truck Flange
NOTE:
Make sure the bumper is in front of the truck
flange bead.
Pull Handle Downward
4. Pull down on the handle to ensure the Slide
Locking Lever is fully engaged. Do this for both
the left and right side.
5. Unclip the stowage straps, and re-snap them
to the bow.
6. Unfold the Tonneau Cover to the second panel
position.
Incorrect Folding — Will Cause Damage
NOTE:
When folding the second and third panels, the
sections MUST be held together to avoid damage
to the cover material. Fold the panel gently. Do not
allow the panels to drop under their own weight.
Second Panel Position
1 — Front Of Truck
2 — J Hook
-------------------------------------------------------------------------------------------------------------------------------------------------------------
GETTING TO KNOW YOUR VEHICLE
107
NOTE:
Unfold the panel gently, and do not allow the
panels to drop under their own weight.
7. Completely unfold the Tonneau Cover.
Position Two (Fully Unfolded)
8. Repeat steps 2 through 3 for the rear pair of
latches.
9. Pull down on the handle to ensure the Slide
Locking Lever is fully engaged. Do this for both
the left and right side.
NOTE:
Also check to ensure the latch yellow bumpers are
forward of the bead on the underside of the truck
flange. Make sure that the Tonneau Cover is posi
-
tioned fully forward, so that the bumper clears the
bead.
Pull Up On Tonneau Cover Corners
10. Gently pull up on all four corners of the
Tonneau Cover to ensure that it is properly
latched.
T
RI
-F
OLD
T
ONNEAU
C
OVER
C
LEANING
For proper cleaning of the Tonneau Cover, use
Mopar® Whitewall & Vinyl Top Cleaner and
Mopar® Leather & Vinyl Conditioner/Protectant.
CAUTION!
The vehicle cannot be driven when the Tonneau
Cover is in the second panel position.
CAUTION!
It is the driver’s responsibility to ensure the
Tonneau Cover is properly installed on the
vehicle. Failure to follow this procedure can
result in detachment of the Tonneau Cover
from the vehicle and/or damage to the
vehicle/Tonneau Cover.
2
-------------------------------------------------------------------------------------------------------------------------------------------------------------
108
GETTING TO KNOW YOUR INSTRUMENT PANEL
BASE / MIDLINE INSTRUMENT CLUSTER — GASOLINE
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст