Chevrolet Silverado / GMC Sierra. Manual — part 2276
1. Install the knuckle on the lower ball joint. Refer to Lower Control Arm Replacement
(1500) or Lower Control Arm Replacement (2500, 3500).
2. Install the upper ball joint in the knuckle. Refer to Upper Control Arm Replacement
(1500) or Upper Control Arm Replacement (2500, 3500).
3. Install the outer tie rod end. Refer to Steering Linkage Outer Tie Rod Replacement .
4. Install the wheel bearing and hub assembly. Refer to Front Wheel Hub, Bearing, and
Seal Replacement (2500) or Front Wheel Hub, Bearing, and Seal Replacement
(1500).
5. Install the wheel drive shaft, if equipped. Refer to Wheel Drive Shaft Replacement
(2500) or Wheel Drive Shaft Replacement (1500) .
2008 Chevrolet Silverado 1500
2008 SUSPENSION Front Suspension - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra & Silverado
Fig. 9: Supporting Lower Control Arm
Courtesy of GENERAL MOTORS CORP.
6. Remove the support from the lower control arm.
7. Install the tire and wheel. Refer to Tire and Wheel Removal and Installation .
8. Verify the wheel alignment. Refer to Wheel Drive Shaft Replacement (2500) or Wheel
Drive Shaft Replacement (1500) .
STEERING KNUCKLE REPLACEMENT (1500)
Removal Procedure
2008 Chevrolet Silverado 1500
2008 SUSPENSION Front Suspension - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra & Silverado
Fig. 10: View Of Steering Knuckle (1500)
Courtesy of GENERAL MOTORS CORP.
1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .
2. Remove the tire and wheel. Refer to Tire and Wheel Removal and Installation .
3. Remove the wheel drive shaft, if equipped. Refer to Wheel Drive Shaft Replacement
(2500) or Wheel Drive Shaft Replacement (1500) .
4. Remove the wheel bearing and hub assembly. Refer to Front Wheel Hub, Bearing, and
Seal Replacement (2500) or Front Wheel Hub, Bearing, and Seal Replacement
(1500).
5. Remove the outer tie rod end from the knuckle. Refer to Steering Linkage Outer Tie Rod
Replacement .
6. Separate the upper control arm from the knuckle. Refer to Upper Control Arm
Replacement (1500) or Upper Control Arm Replacement (2500, 3500).
7. Separate the lower control arm from the knuckle. Refer to Lower Control Arm
Replacement (1500) or Lower Control Arm Replacement (2500, 3500).
8. Remove the knuckle from the vehicle.
Installation Procedure
2008 Chevrolet Silverado 1500
2008 SUSPENSION Front Suspension - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra & Silverado
Fig. 11: View Of Steering Knuckle (1500)
Courtesy of GENERAL MOTORS CORP.
1. Install the lower ball joint in the knuckle. Refer to Lower Control Arm Replacement
(1500) or Lower Control Arm Replacement (2500, 3500).
2. Install upper ball joint in the knuckle. Refer to Upper Control Arm Replacement (1500)
or Upper Control Arm Replacement (2500, 3500).
3. Install the outer tie rod end in the knuckle. Refer to Steering Linkage Outer Tie Rod
Replacement .
4. Install the wheel bearing and hub assembly. Refer to Front Wheel Hub, Bearing, and
2008 Chevrolet Silverado 1500
2008 SUSPENSION Front Suspension - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra & Silverado
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст