Chevrolet Silverado / GMC Sierra. Manual — part 2806
Transfer Case Fluid Replacement .
Clean or properly route the vent hose.
Replace the front case half if the seal bore is
damaged. Refer to Transfer Case Disassemble
and Transfer Case Assemble .
Replace the front output shaft seal. Refer to Front
Output Shaft Seal Replacement .
Leaking at the vent
Transfer case overfilled
1. Inspect for the correct transfer case fluid level.
Refer to Transfer Case Fluid Replacement .
2. Inspect the transmission fluid level. Refer to
Transmission Fluid Check .
3. If the transmission fluid level is low, and the
transfer case fluid level is too high, replace the
transfer case input shaft seal. Refer to Input Shaft
Seal Replacement .
4. Inspect for the following conditions:
Seal improperly installed, worn, or damaged
Seal bore damaged or cracked
Input shaft seal surface worn, grooved, or
damaged
Seal the vent with the correct sealer if leaking at the case.
Refer to Transfer Case Assemble.
Transfer case to adapter
leak
1. Inspect for the following conditions:
Loose mounting fasteners
Gasket or sealant faulty
The transfer case input shaft seal leaking
2. Repair or replace the following components if found
faulty:
Replace the transfer case input shaft seal. Refer to
Input Shaft Seal Replacement .
Inspect for the following:
Seal improperly installed, worn, or damaged
Seal bore damaged or cracked
2008 Chevrolet Silverado 1500
2008 TRANSMISSION Transfer Case - BW 4485-NR3 - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra &
Silverado
REPAIR INSTRUCTIONS - ON VEHICLE
TRANSFER CASE SHIELD REPLACEMENT
Fig. 3: View Of Transfer Case Shields & Bolts
Courtesy of GENERAL MOTORS CORP.
Input shaft seal surface worn, grooved, or
damaged
Repair or replace the loose fasteners. Refer to
Transfer Case Adapter Replacement .
Replace the transfer case gasket or sealer. Refer to
Transfer Case Adapter Replacement .
Front case half to rear case
half seam leak
Disassemble and seal the case halves. Refer to Transfer Case
Disassemble and Transfer Case Assemble.
Case leaking
1. Inspect for a cracked case or case porosity.
2. Replace the faulty case half. Refer to Transfer Case
Disassemble and Transfer Case Assemble.
2008 Chevrolet Silverado 1500
2008 TRANSMISSION Transfer Case - BW 4485-NR3 - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra &
Silverado
TRANSFER CASE FLUID REPLACEMENT
Removal Procedure
Callout
Component Name
Preliminary Procedure:
Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .
1
Transfer Case Shield Bolt
Tighten: 20 N.m (15 lb ft)
NOTE:
Refer to Fastener Notice .
2
Transfer Case Shield
IMPORTANT: When performing the following procedure, use only hand tools to
remove and install the drain and fill plugs.
2008 Chevrolet Silverado 1500
2008 TRANSMISSION Transfer Case - BW 4485-NR3 - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra &
Silverado
Fig. 4: View Of Transfer Case Fill Plug
Courtesy of GENERAL MOTORS CORP.
1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle .
2. Remove the transfer case shield, if equipped. Refer to Transfer Case Shield
Replacement.
3. Remove the fill plug.
2008 Chevrolet Silverado 1500
2008 TRANSMISSION Transfer Case - BW 4485-NR3 - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra &
Silverado
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст