Chevrolet Silverado / GMC Sierra. Manual — part 1242
Fig. 26: View Of Hood Spring & Open Assist Bolts
Courtesy of GENERAL MOTORS CORP.
REAR SIDE DOOR HINGE REPLACEMENT (EXTENDED CAB)
Callout
Component Name
Preliminary Procedures: Remove the hood. Refer to Hood Replacement.
CAUTION:
When a hood hold open device is being removed or installed, provide alternate support to avoid the
possibility of damage to the vehicle or personal injury.
1
Hood Open Assist Spring Bolt (Qty: 2)
Tighten: 22 N.m (16 lb ft)
NOTE:
Refer to Fastener Notice .
2
Hood Spring
2008 Chevrolet Silverado 1500
2008 ACCESSORIES & EQUIPMENT Bolted Exterior Body Panels and Closures - Cab & Chassis Sierra, Cab & Chassis
Silverado, Sierra & Silverado
Microsoft
Friday, August 21, 2009 2:23:22 PM
Page 31
© 2005 Mitchell Repair Information Company, LLC.
Fig. 27: View Of Rear Side Door Hinge Components
Courtesy of GENERAL MOTORS CORP.
Callout
Component Name
Preliminary Procedures:
Remove the body hinge pillar trim. Refer to Body Hinge Pillar Trim Panel Replacement .
1
Rear Side Door Upper Hinge to Body Bolt
Tip: One bolt is located behind the body hinge pillar trim.
2
Rear Side Door Lower Hinge to Body Bolt
Tip: One bolt is located behind the body hinge pillar trim.
3
Rear Side Door Upper Hinge to Body Bolt (Qty: 2)
Procedure
1. Disconnect the electrical connector, if equipped.
2. Tape the edges of the door and body.
3. Support the door before removing hinge bolts from step 3 and 4.
Tighten: 26 N.m (19 lb ft)
NOTE:
Refer to Fastener Notice .
2008 Chevrolet Silverado 1500
2008 ACCESSORIES & EQUIPMENT Bolted Exterior Body Panels and Closures - Cab & Chassis Sierra, Cab & Chassis
Silverado, Sierra & Silverado
Microsoft
Friday, August 21, 2009 2:23:22 PM
Page 32
© 2005 Mitchell Repair Information Company, LLC.
REAR SIDE DOOR HINGE REPLACEMENT (CREW CAB)
Fig. 28: View Of Rear Side Door Hinge & Components
Courtesy of GENERAL MOTORS CORP.
4
Rear Side Door Lower Hinge to Body Bolt (Qty: 2)
Tip: Remove the door from the vehicle then remove the door side hinge bolts.
Tighten: 26 N.m (19 lb ft)
5
Rear Side Door Upper Hinge to Door Bolt (Qty: 2)
6
Rear Side Door Lower Hinge to Door Bolt (Qty: 2)
7
Rear Side Door Lower Hinge
Callout
Component Name
1
Rear Side Door Hinge Upper Bolt (Qty: 2)
Tighten: 25 N.m (18 lb ft)
NOTE:
Fastener Notice .
Rear Side Door Hinge Upper Bolt (Qty: 2)
2008 Chevrolet Silverado 1500
2008 ACCESSORIES & EQUIPMENT Bolted Exterior Body Panels and Closures - Cab & Chassis Sierra, Cab & Chassis
Silverado, Sierra & Silverado
Microsoft
Friday, August 21, 2009 2:23:22 PM
Page 33
© 2005 Mitchell Repair Information Company, LLC.
HOOD REPLACEMENT
2
Tighten: 25 N.m (18 lb ft)
3
Rear Side Door Upper Hinge
Tip: Check the door for proper alignment, then adjust as necessary.
4
Rear Side Door Hinge Lower Bolt
Tip: After installation of the replacement upper hinge, from the underside of the hinge,
remove the temporary keeper pivot bolt and replace with longer permanent bolt.
Tighten: 25 N.m (18 lb ft)
5
Rear Side Door Hinge Lower Bolt (Qty: 2)
Tighten: 25 N.m (18 lb ft)
6
Rear Side Door Hinge Lower Bolt (Qty: 2)
Tighten: 25 N.m (18 lb ft)
7
Rear Side Door Lower Hinge
Tip: Check the door for proper alignment, then adjust as necessary.
2008 Chevrolet Silverado 1500
2008 ACCESSORIES & EQUIPMENT Bolted Exterior Body Panels and Closures - Cab & Chassis Sierra, Cab & Chassis
Silverado, Sierra & Silverado
Microsoft
Friday, August 21, 2009 2:23:22 PM
Page 34
© 2005 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст