DAF 95XF. Manual — part 162
©
200438
1-1
UPEC fault codes
UPEC
DAVIE XD diagnostics manual
2
1. UPEC FAULT CODES
1.1 INTRODUCTION
If the electronic unit detects a system fault, this
fault is usually stored in the memory of the
electronic unit as a fault code.
Most system faults will also generate a warning.
UPEC
1-2
©
200438
UPEC fault codes
2
DAVIE XD diagnostics manual
1.2 EXPLANATORY NOTES TO UPEC FAULT CODES
Fault code
Fault code description with possible cause
Symptom
11-1
Internal communication fault in ECU
-
Engine stalls and/or engine starts but does
not fire
11-2
Internal communication fault in ECU
-
Engine stalls and/or engine starts but does
not fire
12-1
Internal fault in ECU due to:
-
defective EEPROM
-
No noticeable system limitation in UPEC
13-1
Internal fault in ECU during the checking
procedure after the ignition was switched off
-
No noticeable system limitation in UPEC
13-2
Internal fault in ECU during the checking
procedure after the ignition was switched off
-
No noticeable system limitation in UPEC
13-4
Internal fault in ECU during the checking
procedure after the ignition was switched off
-
No noticeable system limitation in UPEC
13-8
Internal fault in ECU during the checking
procedure after the ignition was switched off
-
No noticeable system limitation in UPEC
14-1
Voltage on pin B15 but no voltage on pins B3 and
B4 of the ECU due to:
-
faulty relay G126
-
no activation of relay G126
-
no supply voltage on relay G126
-
open connection to pin B27
-
short circuit to supply on pin B27
-
Engine stalls and/or engine starts but does
not fire
-
Communication fault with DAVIE so that
fault code cannot be read out
-
Several systems will output error messages
in connection with the CAN communication
15-1
Internal fault in ECU
-
No noticeable system limitation
21-8
Voltage on pins B3 and B4, with no voltage being
applied anymore on pin B15 of the ECU due to:
-
faulty relay G126
-
short circuit to earth on pin B27
-
short circuit to supply on pin B3 and/or B4
-
Engine starts but will not fire
-
Communication fault with DAVIE so that
fault code cannot be read out
-
Several systems will output error messages
in connection with the CAN communication
22-1
Voltage on pins B3, B4 and B15 of the ECU is too
high (>30 V) due to:
-
excessive alternator/battery voltage
-
inductive voltage of external component
-
System response depending on voltage
level
22-2
Voltage on pins B3, B4 and B15 of the ECU is too
low (<14 V) due to:
-
insufficient supply voltage, for example
during starting
-
contact resistance in power supply circuit
-
System response depending on voltage
level
22-4
Internal supply voltage fault in ECU
-
System response depending on internal
supply voltage fault
31-1
Short circuit to supply on pump unit connections,
pin A24 and/or pin A25 of the ECU
-
Engine stalls and/or engine starts but does
not fire
©
200438
1-3
UPEC fault codes
UPEC
DAVIE XD diagnostics manual
2
31-2
Short circuit to earth or interruption in the pump
unit (B131) on pin A35 of the ECU, causing the
pump unit of cylinder 1 to be switched off
-
Engine running on 5 cylinders
-
Reduced engine output
Short circuit to earth on pump unit connections,
pin A24 and/or pin A25 of the ECU
-
Engine stalls and/or engine starts but does
not fire
Short circuit to supply of the pump unit (B131) on
pin A35 of the ECU
-
Engine stalls and/or engine starts but does
not fire
Interruption in the pump unit (B131) on pin A24 of
the ECU, causing the pump unit of cylinders 1, 2
and 3 to be switched off
-
Engine running on 3 cylinders
-
Engine does not supply power
31-4
The valve inside the pump unit (B131) does not
close due to:
-
jammed valve
-
internal contamination
-
internal wear
-
Engine running on 5 cylinders
-
Reduced engine output
The valve inside the pump unit (B131) does not
close fast enough due to:
-
internal contamination
-
internal wear
-
Reduced engine output
31-8
The valve inside the pump unit (B131) does not
open fast enough due to:
-
mechanical problems
-
internal contamination
-
No noticeable system limitation in UPEC
32-1
Short circuit to supply on pump unit connections,
pin A24 and/or pin A25 of the ECU
-
Engine stalls and/or engine starts but does
not fire
32-2
Short circuit to earth or interruption in the pump
unit (B135) on pin A26 of the ECU, causing the
pump unit of cylinder 5 to be switched off
-
Engine running on 5 cylinders
-
Reduced engine output
Short circuit to earth on pump unit connections,
pin A24 and/or pin A25 of the ECU
-
Engine stalls and/or engine starts but does
not fire
Short circuit to supply of the pump unit (B135) on
pin A26 of the ECU
-
Engine stalls and/or engine starts but does
not fire
Interruption in the pump unit (B135) on pin A25 of
the ECU, causing the pump unit of cylinders 4, 5
and 6 to be switched off
-
Engine running on 3 cylinders
-
Engine does not supply power
32-4
The valve inside the pump unit (B135) does not
close due to:
-
jammed valve
-
internal contamination
-
internal wear
-
Engine running on 5 cylinders
-
Reduced engine output
The valve inside the pump unit (B135) does not
close fast enough due to:
-
internal contamination
-
internal wear
-
Reduced engine output
32-8
The valve inside the pump unit (B135) does not
open fast enough due to:
-
mechanical problems
-
internal contamination
-
No noticeable system limitation in UPEC
Fault code
Fault code description with possible cause
Symptom
UPEC
1-4
©
200438
UPEC fault codes
2
DAVIE XD diagnostics manual
33-1
Short circuit to supply on pump unit connections,
pin A24 and/or pin A25 of the ECU
-
Engine stalls and/or engine starts but does
not fire
33-2
Short circuit to earth or interruption in the pump
unit (B133) on pin A34 of the ECU, causing the
pump unit of cylinder 3 to be switched off
-
Engine running on 5 cylinders
-
Reduced engine output
Short circuit to earth on pump unit connections,
pin A24 and/or pin A25 of the ECU
-
Engine stalls and/or engine starts but does
not fire
Short circuit to supply of the pump unit (B133) on
pin A34 of the ECU
-
Engine stalls and/or engine starts but does
not fire
Interruption in the pump unit (B133) on pin A24 of
the ECU, causing the pump unit of cylinders 1, 2
and 3 to be switched off
-
Engine running on 3 cylinders
-
Engine does not supply power
33-4
The valve inside the pump unit (B133) does not
close due to:
-
jammed valve
-
internal contamination
-
internal wear
-
Engine running on 5 cylinders
-
Reduced engine output
The valve inside the pump unit (B133) does not
close fast enough due to:
-
internal contamination
-
internal wear
-
Reduced engine output
33-8
The valve inside the pump unit (B133) does not
open fast enough due to:
-
mechanical problems
-
internal contamination
-
No noticeable system limitation in UPEC
34-1
Short circuit to supply on pump unit connections,
pin A24 and/or pin A25 of the ECU
-
Engine stalls and/or engine starts but does
not fire
34-2
Short circuit to earth or interruption in the pump
unit (B136) on pin A27 of the ECU, causing the
pump unit of cylinder 6 to be switched off
-
Engine running on 5 cylinders
-
Reduced engine output
Short circuit to earth on pump unit connections,
pin A24 and/or pin A25 of the ECU
-
Engine stalls and/or engine starts but does
not fire
Short circuit to supply of the pump unit (B136) on
pin A27 of the ECU
-
Engine stalls and/or engine starts but does
not fire
Interruption in the pump unit (B136) on pin A25 of
the ECU, causing the pump unit of cylinders 4, 5
and 6 to be switched off
-
Engine running on 3 cylinders
-
Engine does not supply power
34-4
The valve inside the pump unit (B136) does not
close due to:
-
jammed valve
-
internal contamination
-
internal wear
-
Engine running on 5 cylinders
-
Reduced engine output
The valve inside the pump unit (B136) does not
close fast enough due to:
-
internal contamination
-
internal wear
-
Reduced engine output
Fault code
Fault code description with possible cause
Symptom
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст