DAF 95XF. Manual — part 602
8
TRAILING AXLES
Removal and installation
3-2
5.
Remove the locking washer (3) and the
circlip (4) from the axle journal.
6.
Position a tyre lift under the wheel.
7.
Remove the hub nut (5) using special tool
(DAF No. 0694783).
8.
Remove the outer wheel bearing (6) from
the hub.
Note:
If the bearings are removed from both
wheels, the bearings should be marked.
Each bearing should be re-installed in its
original hub.
9.
Remove the hub with the wheel from the
axle journal.
10. Remove the oil seal (13) from the hub using
an internal puller. Make sure that the
chamber in the hub is not damaged.
11. Remove the inner wheel bearing (12) from
the hub.
12. Remove the grease from the hub and clean
it.
13. Clean the bearings.
14. Remove the outer races of the wheel
bearings, if necessary.
5
ǹ 200302
8
Removal and installation
TRAILING AXLES
3-3
A8 00 439
7
8
9
10
12
11
13
1
2
3
4
5
6
Installing the wheel hub (09N075)
1.
Check the hub and the wheel bearings for
wear and damage. See chapter “Inspection
and adjustment”.
2.
Fit new wheel bearings into the hub, if
necessary.
3.
Blow-dry the wheel bearings (6) and (12)
using compressed air.
4.
Fill the wheel bearings with the specified
wheel bearing grease.
Also apply a layer of grease to the wheel
bearing circumference.
ǹ 200302
5
8
TRAILING AXLES
Removal and installation
3-4
5.
Fit the wheel bearing (12) into the hub.
6.
Fill the inside circumference of the hub with
wheel bearing grease.
7.
Fit a new hub oil seal (13) in the hub.
8.
Apply a little grease to the sealing lips of the
oil seal.
9.
Position the wheel in front of the axle
journal using the tyre lift.
Fit the outer wheel bearing (6) into the hub
so that the outer wheel bearing can also
serve as a guide when installing the hub.
10. Slide the hub over the axle journal. Do not
pry, as the oil seal (13) might be damaged
in the process.
11. Fit the hub nut (5) to the axle journal.
12. Adjust the specified wheel bearing play (see
chapter “Inspection and adjustment”) and fit
the circlip (4) to the axle journal.
13. Fit a new locking washer (3) to the axle
journal. The cam of the locking washer
should fall into one of the holes of the
circlip (4).
14. Fit the lock nut (2) to the axle journal.
Tighten the lock nut (2) to the specified
tightening torque. See main group
“Technical data”. Use special tool
(DAF No. 0535832).
15. Secure lock nut (2) by tapping back the
locking washer (3) against the side of the
lock nut.
16. Apply the specified grease to the front of the
outer wheel bearing.
17. Apply the specified sealant to the hub cover
(1) and tighten it to the specified tightening
torque. See main group “Technical data”.
18. Adjust the brakes.
S7 00 140
5
ǹ 200302
8
Removal and installation
TRAILING AXLES
3-5
3.2 REMOVAL AND INSTALLATION, WHEEL HUB (TRAILING AXLE 09N220)
10
11
14
15
13
1
2
12
3
4
5
6
7
8
9
A8 00 438
Removing the wheel hub
(trailing axle 09N220)
1.
Remove the attachment bolts from the hub
cover and remove the hub cover (4).
2.
Lift the trailing axle using the trailing axle
load transfer device.
3.
Release the brakes.
ǹ 200302
5
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст