DAF LF45, LF55 Series. Manual — part 20
©
1-19
AS Tronic fault codes
AS TRONIC
DAVIE XD diagnostics manual
3
3178
Warning CAN communication between all vehicle
systems possibly not OK
-
When driving:
-
no gear changes possible
-
automatic mode not available
-
-
At standstill:
-
if the vehicle comes to a halt, the clutch will
open and the gearbox is automatically
shifted to the neutral position
-
driving off from a stationary position is not
possible
-
system is not available
3179
Overloaded CAN communication system
between all vehicle systems. Not all CAN
messages can be sent in the same cycle.
When driving:
-
no gear changes possible
-
automatic mode not available
At standstill:
-
if the vehicle comes to a halt, the clutch will
open and the gearbox is automatically
shifted to the neutral position
-
driving off from a stationary position is not
possible
-
system is not available
3180
No CAN message received from engine
management (UPEC) due to:
-
communication problem with the engine
management (UPEC)
When driving:
-
no gear changes possible
-
automatic mode not available
At standstill:
-
if the vehicle comes to a halt, the clutch will
open and the gearbox is automatically
shifted to the neutral position
-
driving off from a stationary position is not
possible
-
system is not available
3181
No CAN message received from engine
management (UPEC) due to:
-
communication problem with the engine
management (UPEC)
When driving:
-
no gear changes possible
-
automatic mode not available
At standstill:
-
if the vehicle comes to a halt, the clutch will
open and the gearbox is automatically
shifted to the neutral position
-
driving off from a stationary position is not
possible
-
system is not available
3182
Incorrect or missing cruise control vehicle speed
signal received via CAN message due to:
-
communication problem with the engine
management (UPEC)
-
Wheel speed signals are missing
-
Automatic mode not available
-
When the vehicle is coasting, the clutch will
be opened at a vehicle speed exceeding
1.5 km/h.
3183
Incorrect or missing engine brake signal received
via CAN message from engine management
(UPEC) due to:
-
communication problem with the engine
management (UPEC)
-
If the engine brake is active, this may affect
the shifting quality when shifting is started
-
No further system limitation
-
Automatic mode not available
Fault code
Fault code description with possible cause
Symptom
AS TRONIC
1-20
©
AS Tronic fault codes
3
DAVIE XD diagnostics manual
3184
No CAN message received from the intarder
(EST 42) due to:
-
communication problem with intarder
(EST 42)
-
No noticeable system limitation
-
Automatic mode not available
3188
Internal modulator fault (D954) due to:
-
missing or defective basic program(s)
When driving:
-
no gear changes possible
-
automatic mode not available
At standstill:
-
if the vehicle comes to a halt, the clutch will
open and the gearbox is automatically
shifted to the neutral position
-
driving off from a stationary position is not
possible
-
system is not available
3189
Internal modulator fault (D954) due to:
-
missing or defective basic program(s)
When driving:
-
no gear changes possible
-
automatic mode not available
At standstill:
-
if the vehicle comes to a halt, the clutch will
open and the gearbox is automatically
shifted to the neutral position
-
driving off from a stationary position is not
possible
-
system is not available
3190
Internal modulator fault (D954) due to:
-
missing or defective basic program(s)
-
fault recognised during self-test
When driving:
-
no gear changes possible
-
automatic mode not available
At standstill:
-
if the vehicle comes to a halt, the clutch will
open and the gearbox is automatically
shifted to the neutral position
-
driving off from a stationary position is not
possible
-
system is not available
3191
Internal modulator fault (D954) due to:
-
missing or defective basic program(s)
-
fault recognised during self-test
When driving:
-
no gear changes possible
-
automatic mode not available
At standstill:
-
if the vehicle comes to a halt, the clutch will
open and the gearbox is automatically
shifted to the neutral position
-
driving off from a stationary position is not
possible
-
system is not available
3192
Internal modulator fault (D954) due to:
-
communication problem between
processors in modulator
-
If the fault still occurs after the ignition has
been switched off and on, an average drive-
off gear will be selected when driving off
from a stationary position
-
No noticeable system limitation
-
Automatic mode not available
Fault code
Fault code description with possible cause
Symptom
©
1-21
AS Tronic fault codes
AS TRONIC
DAVIE XD diagnostics manual
3
3193
The modulator temperature measured by the
integrated temperature sensor is too high:
-
temperature > 130 degrees Celsius
When driving:
-
no gear changes possible
-
automatic mode not available
At standstill:
-
if the vehicle comes to a halt, the clutch will
open and the gearbox is automatically
shifted to the neutral position
-
driving off from a stationary position is not
possible
-
system is not available
3194
Front axle speed signals not recognised via
message on CAN network
-
No noticeable system limitation
-
Automatic mode not available
3198
Relative wheel speed sensor signals not
recognised via message on CAN network
-
No noticeable system limitation
-
Automatic mode available
3199
No CAN message received from ABS/EBS unit
due to:
-
communication problem with ABS/EBS
-
An average drive-off gear is selected when
driving off from a stationary position
-
No noticeable system limitation
-
Automatic mode available
3210
No CAN message received from the MTCO due
to:
-
communication problem with the MTCO
-
No noticeable system limitation, if there is a
redundant internal speed signal
-
Automatic mode available
3227
Internal modulator fault (D954) due to:
-
missing or defective basic program(s)
-
fault recognised during self-test
When driving:
-
no gear changes possible
-
automatic mode not available
At standstill:
-
if the vehicle comes to a halt, the clutch will
open and the gearbox is automatically
shifted to the neutral position
-
driving off from a stationary position is not
possible
-
system is not available
3235
No PTO active signal received by AS Tronic ECU
from VIC via CAN message due to:
-
communication problem with the VIC
-
No PTO 1 and PTO 2 actuation possible
3236
No CAN message received from the VIC due to:
-
communication problem with the VIC
-
No PTO 1 actuation possible
3237
No CAN message received from the VIC due to:
-
communication problem with the VIC
-
No PTO 2 actuation possible
Fault code
Fault code description with possible cause
Symptom
AS TRONIC
1-22
©
AS Tronic fault codes
3
DAVIE XD diagnostics manual
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст