DAF CF65, CF75, CF85 Series . Manual — part 1138
©
200518
5-9
Draining and filling
EXPLANATORY NOTES ON THE MAINTENANCE ACTIVITIES
ΧΦ65/65 (II) series
5
5.6 FILLING GREASE SUPPLY OF THE AUTOMATIC LUBRICATION SYSTEM
1.
Remove the dust cover from the filler
coupling.
2.
Connect the filler hose to the filler coupling.
Ensure that the filler hose is completely filled
with grease so that no air bubbles can get
into the system.
3.
Fill the reservoir to the specified maximum
level.
Note:
When filling the reservoir, the air above the
follower piston will escape. This air will flow
down through an opening in the piston line
and escape from the pump through the right-
angled coupling. Normally a small amount of
grease will escape from this coupling during
venting.
4.
Remove the filler hose from the filler
coupling.
C900331
EXPLANATORY NOTES ON THE MAINTENANCE ACTIVITIES
5-10
©
200518
Draining and filling
5
ΧΦ65/65 (II) series
©
200518
6-1
Cleaning
EXPLANATORY NOTES ON THE MAINTENANCE ACTIVITIES
ΧΦ65/65 (II) series
5
6. CLEANING
6.1 CLEANING THE BATTERY POLES
Avoid sparks and open flames in the
vicinity of batteries.
Battery acid is an aggressive fluid.
In the event of contact with the skin:
rinse the skin with plenty of water for
a sustained period. If redness or
pain persists, consult a doctor.
Remove any clothing affected and
rinse with water.
In the event of contact with the eyes:
rinse with plenty of water for at least
15 minutes and consult a doctor.
If swallowed: do NOT induce
vomiting. Rinse the mouth, drink two
glasses of water and consult a
doctor.
In the event of inhalation: get fresh
air, rest and consult a doctor.
1.
Disconnect the earth lead from the battery
terminal.
2.
Disconnect the positive lead from the battery
terminal.
3.
Clean the battery terminals, battery cables
and the top of the battery (oxide and dirt
discharge the battery).
4.
If the top of the battery has acid on it, it
should be rinsed with water.
5.
Grease the battery terminals with Vaseline.
6.
Check the earth lead connection to the
chassis and grease the connection with
Vaseline.
7.
Fit the positive lead to the battery terminal.
8.
Fit the earth lead to the battery terminal.
9.
Check the routing and attachment of the
battery cables.
}
M5008
EXPLANATORY NOTES ON THE MAINTENANCE ACTIVITIES
6-2
©
200518
Cleaning
5
ΧΦ65/65 (II) series
6.2 CLEANING RADIATOR AND INTERCOOLER
Inhalation of dust may have serious
consequences for your health.
Take the necessary precautions,
such as wearing goggles and a
facemask.
Key to drawing:
Note:
With the aid of a simple tool, the radiator and the
intercooler can be blow-cleaned.
The tool (radiator cleaner) cannot be ordered
from DAF. It should be manufactured by you
according to the drawing.
1.
Remove the protective screen, if applicable,
by removing the attachment bolts.
2.
Clean the protective screen, if applicable,
with a hard brush, and blow-clean with
compressed air.
3.
Insert radiator cleaner (4) between
intercooler (1) and radiator (2) with the air
holes facing the intercooler (1).
4.
Apply air pressure to the radiator cleaner (4)
and continue blow-cleaning the intercooler
(1) until no more dirt comes out.
}
100mm
5mm
2
1150mm
2
4
3
5
5
4
1
1
M2108
1
Solder up
2
Solder
3
Quick-release coupling for air hose
4
Steel pipe,
10 mm
5
6 x
1.5 mm between holes, with a
centre-to-centre distance between the
holes of 7 mm, drilled on one side
1
2
3
4
M2109
P
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст