DAF CF65, CF75, CF85 Series . Manual — part 1044
©
200424
3-1
Removal and installation
TANDEM REAR AXLE 1132T
ΧΦ65/75/85 series
8
6
3. REMOVAL AND INSTALLATION
3.1 REMOVAL AND INSTALLATION, ENTIRE REAR AXLE
Removing the entire rear axle
1.
Block the front wheels using chocks.
2.
Slacken the central bolt of the spring-brake
cylinder as much as possible.
3.
Apply the parking brake.
4.
Remove the air pipes and wiring.
5.
Remove the prop shaft from the drive flange.
6.
Loosen the shock absorbers on the bottom.
7.
Loosen the control rod of the ALR valve.
8.
Support the vehicle securely with stands
under the chassis side members.
9.
Remove the axle suspension/guide.
Take precautionary measures to make sure
that the axle does not tilt during removal of
the axle suspension/guide.
10. If possible, the entire rear axle with wheels
should be rolled from under the vehicle.
Installing the entire rear axle
1.
Install the entire rear axle with wheels under
the vehicle.
2.
Fit the axle suspension/guide.
Make sure that the torque-rod supports are
fitted so that arrow A on the support points in
the driving direction.
3.
Fit the control rod of the ALR valve.
Note:
Check the setting of the ALR valve following
installation of the rear axle.
4.
Fit the shock absorbers (if applicable).
5.
Fit the prop shaft to the drive flange.
6.
Connect the electrical wiring and fit the air
pipes.
7.
Tighten the central bolt of the spring-brake
cylinder.
A
A800045
TANDEM REAR AXLE 1132T
3-2
©
200424
Removal and installation
6
ΧΦ65/75/85 series
8
3.2 REMOVAL AND INSTALLATION, AXLE SHAFTS
Removing axle shafts
1.
Jack up the rear axle and support the axle on
stands.
2.
Engage the differential lock. Check whether
the axle is blocked. Replace the switch by
the special tool (DAF no. 1329447), see (A).
This is to prevent the sliding sleeve from
falling into the differential when removing the
axle shaft.
3.
Remove the axle-shaft attachment bolts.
4.
Remove the axle shaft using special tool
(DAF no. 0694980), if required, see (B).
When the axle shaft comes loose, a small
amount of oil may leak out. Collect this oil.
A
A800139
B
A8 00 351
©
200424
3-3
Removal and installation
TANDEM REAR AXLE 1132T
ΧΦ65/75/85 series
8
6
Installing axle shafts
1.
Clean the mating surfaces of the axle shaft
flange and wheel hub unit.
2.
Apply sealant to the mating surface of the
axle shaft flange. See "Technical data".
3.
Fit the axle shaft. Tighten the axle shaft
attachment bolts to the specified tightening
torque, see "Technical data".
4.
Activate the differential lock and remove the
special tool from the differential lock. Install
the switch.
TANDEM REAR AXLE 1132T
3-4
©
200424
Removal and installation
6
ΧΦ65/75/85 series
8
3.3 REMOVAL AND INSTALLATION, WHEEL HUB
Removing the wheel hub
1.
Jack up the rear axle and support the axle on
stands.
2.
Remove the wheels.
3.
Release the brakes.
4.
Remove the brake drum.
5.
Remove the axle shaft.
6.
Remove the lock nut (1) using special tool
(DAF no. 0694894).
7.
Remove the circlip (2).
8.
Remove the hub nut (3) using special tool
(DAF no. 0694894).
9.
Remove the wheel hub from the axle journal.
Installing the wheel hub
1.
Replace the wheel hub oil seal.
2.
Oil the axle journal and the inner and outer
bearing and slide the wheel hub over the axle
journal. Use the outer bearing as a guide.
3.
Fit the hub nut and adjust the wheel bearing
play. See "Inspection and adjustment".
A8 00 425
1
2
3
4
5
6
7
8
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст