DAF CF65, CF75, CF85 Series . Manual — part 283
0
3
CF65/75/85 series
Clutch
TECHNICAL DATA
9-5
9.2 TIGHTENING TORQUES
The tightening torques stated in this section are
different from the standard tightening torques
included in the overview of standard tightening
torques.
Any other threaded connections that are
not specified must therefore be tightened to the
torque stated in the overview of
standard tightening torques.
When attachment bolts and nuts are to be
replaced, it is important that they are of exactly
the same length and property class as the ones
removed unless stated otherwise.
Main cylinder
Pressure pin attachment nut
55 Nm
Bleeder
8 Nm
Steel pipe coupling
40 Nm
Clutch release assembly
ZF gearboxes
Attachment bolts, clutch release assembly to
flywheel
54 Nm
Attachment bolt, automatically adjusting clutch
release assembly stop plate
39 Nm
(1)
(1)
Loctite 648
ZF 6S-850
Attachment bolts, clutch release assembly to
flywheel
54 Nm
Attachment bolts, clutch lever to gearbox
27 Nm
8/9/16S-109
M16 round bolt, clutch lever to clutch housing
90 Nm
8/16S-151/181/221
M8 attachment bolts, clutch lever to gearbox
30 Nm
EATON FS/6309A gearbox
Attachment bolts, clutch release assembly to
flywheel
54 Nm
Attachment bolts, clutch lever to gearbox
27 Nm
ᓻ 200337
3
TECHNICAL DATA
Clutch
CF65/75/85 series
9-6
AS TRONIC gearbox
M12 attachment bolts, clutch lever to gearbox
79 Nm
AS TRONIC clutch unit
Clutch unit attachment nut
23 Nm
Clutch unit stud
10 Nm
Bleed screw, clutch unit
22 Nm
Compressed air connection
50 Nm
9.3 FILLING CAPACITIES
Clutch operating unit
First filling
0.4 litres
0
ᓻ 200337
0
3
CF65/75/85 series
Prop shafts
TECHNICAL DATA
10-1
10. PROP SHAFTS
10.1 GENERAL
For the
CF 65/75/85 vehicle series, DAF has
one manufacturer of prop shafts, Klein.
Klein shafts can be identified by their highly
bevelled flanges.
Inspection
There must be no clearly noticeable play on
universal joints, centre bearing or sliding clutch.
Universal joint radial play
0.01 - 0.05 mm
Maximum permissible axial play of universal
joints
0.3 mm
CF65
Balancing speed (
∅ 85 x 5 mm)
retracted length
≤ 1750 mm
max. n = 3000 n/
min
Length of idler shaft
≤ 1950 mm
CF75
Balancing speed (
∅ 120 x 3 mm)
retracted length
≤ 2120 mm
max. n = 3000 n/
min
Length of idler shaft
≤ 2340 mm
CF85
Balancing speed (
∅ 120 x 5 mm)
retracted length
≤ 2120 mm
max. n = 3000 n/
min
Length of idler shaft
≤ 2340 mm
Balanceertoerental (
∅ 140 x 5 mm)
retracted length
≤ 2320 mm
max. n = 3000 n/
min
Length of idler shaft
≤ 2500 mm
Centre bearings
If a lubricating nipple is fitted to the
CF65/75/85,
it must be lubricated.
ᓻ 200337
3
TECHNICAL DATA
Prop shafts
CF65/75/85 series
10-2
Maximum permissible axial play of slide joint
0.25 mm
45
A
B
C
D
V300444
10.2 TIGHTENING TORQUES
The tightening torques stated in this section are
different from the standard tightening torques
included in the overview of standard tightening
torques.
Any other threaded connections that are
not specified must therefore be tightened to the
torque stated in the overview of
standard tightening torques.
When attachment bolts and nuts are to be
replaced, it is important that they are of exactly
the same length and property class as the ones
removed unless stated otherwise.
Attachment bolts, drive flanges
M12 - 10.9
110 Nm
M14 - 10.9
170 Nm
Centre bearing central nut
M24 x 1.5
250 Nm
M40 x 1.5
350 Nm
M55 x 1.5
380 Nm
Centre bearing attachment bolts
170 Nm
(1)
(1)
Loctite 243
0
ᓻ 200337
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст