DAF CF65, CF75, CF85 Series . Manual — part 1135
©
200518
4-9
Removal and installation
EXPLANATORY NOTES ON THE MAINTENANCE ACTIVITIES
ΧΦ65/65 (II) series
5
4.7 REMOVAL AND INSTALLATION, STEERING GEAR FILTER ELEMENT
Removing the steering gear filter element
1.
Clean the reservoir cover, so that absolutely
no dirt can get into the reservoir.
2.
Remove the cover (3).
3.
Rotate the filter holder (5) a quarter turn.
Slowly remove the filter holder (5) together
with the filter element (6) from the
reservoir (1).
Note:
The filter holder and filter element must be
removed from the reservoir (1) with care so
that no dirt remains in the reservoir (1).
4.
Remove the filter element (6) from the filter
holder (5).
Installing the steering gear filter element
1.
Fit a new filter element (6) in the filter
holder (5).
2.
Fit the filter holder (5) together with the filter
element (6) in the reservoir (1) and rotate the
filter holder (5) a quarter turn. Make sure that
the filter holder (5) engages in its locking
element.
3.
Check the sealing ring (4) for damage and
replace if necessary.
4.
Fit the cover (3).
5.
Check the fluid level using the dipstick (2);
see chapter "Inspection and adjustment".
S7 00 689
1
2
3
4
5
6
EXPLANATORY NOTES ON THE MAINTENANCE ACTIVITIES
4-10
©
200518
Removal and installation
5
ΧΦ65/65 (II) series
4.8 REMOVAL AND INSTALLATION, AIR DRYER FILTER ELEMENT
Note:
To be certain that the air dryer is functioning
properly, the air reservoirs should regularly be
checked for condensation. If more than the
normal amount of water is drained off repeatedly,
the air dryer element must be replaced. Under
normal circumstances the element must be
replaced at least once per year.
Removing air dryer filter element
1.
Vent the air dryer by allowing it to regenerate
or by loosening the compressor line (1), so
that the interior of the air dryer is
depressurised.
2.
Remove the filter element by turning it anti-
clockwise using a filter strap spanner.
3.
Dispose of the drying element as if it were an
oil filter.
4.
Clean the air dryer internally.
5.
Check the air dryer threaded connection (2)
for damage and then lubricate it sparingly
with grease.
Installing the air dryer filter element
1.
Lubricate the sealing ring of the new filter
element sparingly with grease.
2.
Fit the filter element by manually tightening it
until the sealing ring abuts. Then tighten the
element by hand (approx. 1 turn).
3.
Fasten the compressor line (1).
4.
Pressurise the system and then check the air
dryer for any air leaks.
R600525
1
R600526
2
©
200518
4-11
Removal and installation
EXPLANATORY NOTES ON THE MAINTENANCE ACTIVITIES
ΧΦ65/65 (II) series
5
5.
Using a water-resistant felt pen, write on the
sticker the latest date by which the dryer
element must be replaced (not later than
1 year after the date of fitting).
Drive and chassis
Artikelnummer
Reference
Teilenummer
Référence
Eerstvolgende vervanging
Next change
Nächster Wechsel
Prochain remplacement
1391510
R600523
EXPLANATORY NOTES ON THE MAINTENANCE ACTIVITIES
4-12
©
200518
Removal and installation
5
ΧΦ65/65 (II) series
4.9 REMOVAL AND INSTALLATION, AUTOMATIC GEARBOX OIL FILTERS
To prevent skin injury, avoid
unnecessary contact with the
drained oil.
Removing automatic gearbox oil filters
1.
Remove the attachment bolts from the filter
covers (2) and remove the filter covers.
Collect any oil that is flowing out.
2.
Remove the oil filters from the oil sump.
3.
Remove the various O-rings from the filter
covers.
4.
If a gasket is used, remove the any pieces of
the gasket left on the filter covers and the
contact surfaces.
Fitting automatic gearbox oil filters
1.
Lightly lubricate the new O-rings with clean
gearbox oil and fit the various O-rings to the
filter covers.
Note:
Compare the new O-rings to the old O-rings
to ensure that the correct O-rings are used.
2.
If a gasket is used, fit a new gasket to the
filter cover.
3.
Lightly lubricate the rubber inner ring of the
oil filters with clean gearbox oil and fit the oil
filters to the filter covers.
4.
Fit the filter covers together with the oil filters
to the gearbox and tighten the attachment
bolts to the specified torque, see main group
"Technical data".
5.
Check the oil level, see chapter "Inspection
and adjustment".
}
V300371
2
1
W 3 03 103
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст