DAF CF65, CF75, CF85 Series . Manual — part 996
©
200423
2-1
Inspection and adjustment
STEERED TRAILING SWIVEL AXLE
ΧΦ65/75/85 series
7
7
2. INSPECTION AND ADJUSTMENT
2.1 INSPECTION AND ADJUSTMENT, SWIVEL AXLE PLAY
Inspection of swivel axle play
1.
The vehicle should have its wheels on the
ground.
Note:
If the wheels have been removed from the
front axle, e.g. for overhaul purposes, the
swivel axle will hang at the axle end.
In that case, the swivel axle should be
supported by a jack, pushing the swivel axle
against the bottom of the axle end.
2.
Using a feeler gauge measure the distance
between the shim and the swivel axle at (A).
Take measurements in several places.
Compare the reading with the admissible
play. See 'Technical data'.
Note:
The play should be about equal along the
entire circumference of the axle end. If the
play is not equal, this is caused by radial play
in the needle bearings. If the radial play of
one of the values measured along the
circumference differs from the specified
value, the needle bearings should be
replaced, see the chapter 'Removal and
installation'.
If an excessive axial play is measured along
the entire circumference of the axle end, this
is probably caused by a worn swivel axle
thrust bearing.
Adjusting the swivel axle play, thrust bearing,
split version
1.
Remove the swivel axle from the axle end.
See 'Removal and installation'.
2.
Degrease and clean the thrust bearing.
3.
Check the thrust bearing for wear or
damage. If in doubt, replace the thrust
bearing.
4.
Check the machined surfaces of the axle end
and the swivel axle for damage.
A
S7 00 579
STEERED TRAILING SWIVEL AXLE
2-2
©
200423
Inspection and adjustment
7
ΧΦ65/75/85 series
7
5.
Remove the dust seal (1) from the thrust
washer (2).
6.
Assemble the thrust bearing without
greasing it and without the dust seal (1).
Make sure that the cam at the bottom of the
bearing ring (3) falls in the recess of shoulder
ring (4). See the arrows in the drawing.
7.
Fit the swivel axle with its original shim on the
axle end.
8.
Fit the king pin. Hand tighten the nut.
9.
Place a jack under the swivel axle, pushing
the thrust bearing against the axle end.
10. Using a feeler gauge measure the gap
between the shim and the swivel axle.
If necessary, use a shim with a different
thickness until the specified axial play is
achieved. See 'Technical data'.
Note:
The shim thickness can also be determined
using the formula in the drawing.
S7 00 114
3
2
1
4
S7 00 815
B
D
A
A=B-(C+D+E)
E
C
A
= shim thickness
B
= distance between the swivel axle
contact surfaces
C
= total thickness of the thrust bearing
without the dust seal
D
= axle end dimensions
E
= play
©
200423
2-3
Inspection and adjustment
STEERED TRAILING SWIVEL AXLE
ΧΦ65/75/85 series
7
7
11. Remove the swivel axle from the axle end.
12. Disassemble the thrust bearing and grease
the top side of bearing ring (3) (ribbed side
with lubricating grooves).
13. Fit a new dust seal (1) to the thrust washer
(2).
Make sure that the top of the dust seal is
positioned under the top of the thrust
washer.
14. Install the swivel axle with the correct shim
on the axle end. See 'Removal and
installation'.
15. Measure the play again.
Adjusting the swivel axle play, thrust bearing,
assembled version
1.
Remove the swivel axle from the axle end.
See 'Removal and installation'.
2.
Check the thrust bearing for wear or
damage. If in doubt, replace the thrust
bearing.
3.
Check the machined surfaces of the axle end
and the swivel axle for damage.
4.
Fit the swivel axle with its original shim on the
axle end.
5.
Fit the king pin. Hand tighten the nut.
6.
Place a jack under the swivel axle, pushing
the thrust bearing against the axle end.
7.
Using a feeler gauge measure the gap
between the shim and the swivel axle.
If necessary, use a shim with a different
thickness until the specified axial play is
achieved. See 'Technical data'.
Note:
The shim thickness can also be determined
using the formula in the drawing.
8.
Remove the swivel axle from the axle end.
S7 00 114
3
2
1
4
S7 00 577
B
D
A
A=B-(C+D+E)
E
C
A
= shim thickness
B
= distance between the swivel axle
contact surfaces
C
= total thickness of the thrust bearing
D
= axle end dimensions
E
= play
STEERED TRAILING SWIVEL AXLE
2-4
©
200423
Inspection and adjustment
7
ΧΦ65/75/85 series
7
9.
Install the swivel axle with the correct shim
on the axle end. See 'Removal and
installation'.
10. Check the play once again.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст