DAF CF65, CF75, CF85 Series . Manual — part 1018
©
200424
3-7
Removal and installation
SINGLE REAR AXLE 1132
ΧΦ65/75/85 series
8
2
10. Tighten the hub nut (1) using the hub nut
wrench (A), which is part of the special tool
set (DAF no. 1329496).
Tighten the hub nut (1) in the specified
manner using a torque amplifier, see
"Technical data".
11. Press the wheel speed sensor (1) up against
the sensor ring (2).
While the vehicle is being driven, the air gap
between the sensor and the sensor ring is
adjusted automatically.
12. Fit the axle shaft.
13. Fit the brake calliper.
14. Put the wheels back on.
A
A8 00 405
1
2
A8 00 342
SINGLE REAR AXLE 1132
3-8
©
200424
Removal and installation
2
ΧΦ65/75/85 series
8
3.4 REMOVAL AND INSTALLATION, WHEEL SPEED SENSOR RING
Removing the wheel speed sensor ring
1.
Remove the wheel hub unit from the axle
journal.
2.
Use a driving tool to carefully tap the sensor
ring from the inside from the wheel hub unit.
Make sure that the wheel hub unit is not
damaged in the process.
Once removed, a sensor ring should
not be re-installed.
Installing the wheel speed sensor ring
1.
Check the mating surfaces of sensor ring
and wheel hub unit for damage.
2.
Check the new sensor ring carefully for
possible damages in transit.
3.
Use a flat plate and a press to fit the sensor
ring to the wheel hub unit.
Press the sensor ring evenly on the wheel
hub unit until it fully abuts.
4.
Install the wheel hub unit on the axle journal.
5.
Press the wheel speed sensor (1) up against
the sensor ring (2).
While the vehicle is being driven, the air gap
between the sensor and the sensor ring is
adjusted automatically.
A8 00 359
}
1
2
A8 00 342
©
200424
3-9
Removal and installation
SINGLE REAR AXLE 1132
ΧΦ65/75/85 series
8
2
3.5 REMOVAL AND INSTALLATION, DRIVE FLANGE
Removing the drive flange
1.
Remove the prop shaft from the drive flange.
2.
Fit the special tool (B) (DAF no. 0484977) on
the drive flange to prevent the flange from
rotating. Remove the drive-flange nut using a
torque amplifier (A).
3.
Remove the drive flange. If necessary, use a
puller.
Installing the drive flange
1.
Before installation check the drive flange
along the oil-seal running surface for
grooves and/or sharp edges. If required,
replace the drive flange.
2.
Fit the drive flange.
3.
Apply a small amount of grease to the first
turn of the drive-flange nut.
4.
Apply locking compound to the screw thread.
See "Technical data".
5.
Fit the special tool (B) (DAF no. 0484977) on
the drive flange to prevent the flange from
rotating. Fit the drive-flange nut. Use a
torque amplifier (A) to tighten the drive-
flange nut to the specified tightening torque,
see "Technical data".
6.
Fit the prop shaft to the drive flange.
A
B
A8 00 357
SINGLE REAR AXLE 1132
3-10
©
200424
Removal and installation
2
ΧΦ65/75/85 series
8
3.6 REMOVAL AND INSTALLATION, PINION OIL SEAL
Removing the pinion oil seal
1.
Remove the drive flange.
2.
Drill two holes into the seal and screw the
special tool (B) (DAF no. 0484899) into the
seal. Pull the oil seal from the pinion housing
using the special tool (A)
(DAF no. 0694928).
Installing the pinion oil seal
1.
Use the special tool (DAF no. 1240452) to fit
the seal so that the inscription "outside" is
pointed outwards.
2.
Fit the drive flange.
A
B
A8 00 360
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст