DAF CF65, CF75, CF85 Series . Manual — part 1036
©
200424
3-3
Removal and installation
SINGLE REAR AXLE 1354
ΧΦ65/75/85 series
8
5
3.3 REMOVAL AND INSTALLATION, WHEEL HUB
Removing the wheel hub
1.
Jack up the rear axle and support the axle on
stands.
2.
Remove the wheels.
3.
Release the brakes and remove the brake
drum.
4.
Mark the hub at the semicircular hole in the
cover.
5.
Drain the oil. See "Draining and filling".
6.
Remove the hub cap.
7.
Remove the axle shaft.
8.
Remove the attachment nuts and tapered
spring washers.
Remove the planet-gear set from the hub
using three jacking screws.
Note:
Make sure that the planet-gear set is put
down with the circlips facing upward. This
will prevent the pins from falling out.
9.
Remove the thrust washer from the axle
journal.
10. Remove the attachment bolts from the
locking plate and remove the locking plate.
A800290
A800107
SINGLE REAR AXLE 1354
3-4
©
200424
Removal and installation
5
ΧΦ65/75/85 series
8
11. Remove the hub nut using special tool
(DAF no. 0535705) and a torque amplifier
(ratio 1 : 5).
12. Support the hub and pull it from the axle
journal. The annular-gear carrier with the
annular gear, the bearings and the spacer
sleeve with spacer rings will be removed at
the same time.
13. Remove the annular-gear carrier with the
annular gear from the hub.
Installing the wheel hub
Note:
If you have not replaced the wheel bearings and
intend to reuse the original spacer sleeve with
spacer rings, you need not readjust the wheel
bearing pre-load.
If the wheel bearings have been replaced, the
wheel bearing pre-load should be re-adjusted,
see chapter "Inspection and adjustment".
You must adjust the wheel bearing pre-load
before fitting the hub seal.
1.
Replace the hub seal.
2.
Check the components for signs of wear
and/or damage.
3.
Replace the O-rings.
4.
Apply oil to the wheel bearings.
5.
Fit the hub on the axle journal.
6.
Fit the original spacer sleeve and spacer
rings.
7.
Fit the inner race of the outer wheel bearing
on the axle journal.
8.
Fit the annular-gear carrier with the annular
gear into the hub and on the splines of the
axle journal.
A800038
©
200424
3-5
Removal and installation
SINGLE REAR AXLE 1354
ΧΦ65/75/85 series
8
5
9.
Fit the hub nut and tighten it using special
tool (DAF no. 0535705) and a torque
amplifier (ratio 1 : 5).
Tighten the hub nut to the specified
tightening torque, see "Technical data".
Turn the hub nut while tightening it.
10. Fit the locking plate. Apply locking
compound to the attachment bolts and
tighten them to the specified torque. See
"Technical data".
11. Install the thrust washer.
12. Fit the planet-wheel set in its original position
in the hub (watch the markings).
13. Install the tapered spring washers and
tighten them to the specified torque. See
"Technical data".
14. Fit the axle shaft.
15. Check the O-ring in the hub cap. If
necessary, replace the O-ring. Apply silicone
grease to the O-ring.
16. Install the spring assembly. Tighten the
attachment bolts to the specified torque. See
"Technical data".
17. Fill the hub with oil. See "Draining and filling".
A800038
A800107
A800290
SINGLE REAR AXLE 1354
3-6
©
200424
Removal and installation
5
ΧΦ65/75/85 series
8
18. Press the sensor (2) against the sensor
ring (1).
While the vehicle is being driven, the air gap
between the sensor and the sensor ring is
adjusted automatically.
3.4 REMOVAL AND INSTALLATION, HUB SEAL/WHEEL SPEED SENSOR RING
UNIT
Removing the hub seal/wheel speed sensor
ring
1.
Remove the hub from the axle journal.
2.
Fit special tool (3) (DAF no. 1329411) to the
impact puller (2), special tool
(DAF no. 0694928).
Fit the special tool (3) behind the seal/sensor
ring (1).
Use the impact puller (2) to pull the seal/
sensor ring (1) evenly from the hub.
Once removed, the seal/sensor ring cannot
be reused.
2
1
A8 00 347
1
2
3
S7 00 424
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст