DAF CF65, CF75, CF85 Series . Manual — part 182
©
200351
9-1
XE-engine lubrication system
TECHNICAL DATA
ΧΦ65/75/85 series
2
0
9. XE-ENGINE LUBRICATION SYSTEM
9.1 GENERAL
Oil pressure
Oil filter
Oil cooler
Oil consumption
Example:
Average measured fuel consumption: 30 litres /
100 km = 300 litres / 1000 km
Maximum admissible engine oil consumption:
0.3% x 300 = 0.9 litres / 1000 km
- Engine oil consumption = 0.9 litres / 1000 km is
permitted
- Engine oil consumption > 0.9 litres / 1000 km;
check the engine using the diagnostics table. See
"Diagnosis".
Oil pressure at engine idling speed
1 bar (warm engine)
Oil pressure at full-load engine speed
3.5 - 4.5 bar
Type
filter element
Number
1
Installation in the oil circuit
full flow
Opening pressure of bypass valve at a pressure
difference of
2.5
≥ 0.3 bar
Coolant test pressure maximum
2.5 bar
Maximum admissible engine oil consumption
0.3% of the average fuel consumption
TECHNICAL DATA
9-2
©
200351
XE-engine lubrication system
0
ΧΦ65/75/85 series
2
9.2 TIGHTENING TORQUES
The tightening torques specified in this paragraph
are different from the standard tightening torques
cited in the overview of the standard tightening
torques. The other threaded connections not
specified must therefore be tightened to the
torque cited in the overview of standard
tightening torques.
When attachment bolts and nuts are replaced, it
is important - unless stated otherwise - that these
bolts and nuts are of exactly the same length and
property class as those removed.
Lubricating oil strip/rocker seats
Oil pan
Oil pump
Strainer
Lubricating oil filter
(1) Use Loctite 243 to secure
(2) Use Loctite 572 to secure
Bypass pressure regulator
Oil cooler
Centrifugal oil filter
Attachment bolts
110 Nm
Clamp attachment bolts
25 Nm
Oil drain plug
60 Nm
Oil level sensor
60 Nm
Attachment bolts for oil pump housing sections
30 Nm
Attachment bolts connecting oil pump to main
bearing cap
60 Nm
Oil delivery pipe attachment bolts
30 Nm
Idler gear central bolt
60 Nm
Bracket attachment bolts
30 Nm
Lubricating oil filter housing attachment bolts
50 Nm
Filter element screw cap
40 Nm
Plug
80 Nm
Attachment bolts connecting oil cooler to cylinder
block
50 Nm
Coolant supply pipe union
90 Nm
Plug, adjustable banjo connection
90 Nm
Banjo bolt, adjustable banjo connection
90 Nm
Central bolt
20 Nm
©
200351
9-3
XE-engine lubrication system
TECHNICAL DATA
ΧΦ65/75/85 series
2
0
Oil nozzle
Main bearing caps
Big-end bearing caps
(1) Apply a drop of oil to thread and contact surface.
(2) Connecting rod bolts are to be used once and tightened
as instructed. When fitting the connecting rod in the
engine, apply a drop of oil to the threads and contact
surfaces of the connecting rod bolts.
Oil nozzle banjo bolt
30 Nm
Main bearing cap attachment bolts
150 Nm + 120
angle tightening
1
5
4
3
2
1
M2 01 285
Attachment bolts (1),
cracked big-end
bearing caps
1
st
phase
100 Nm
2
nd
phase
175 Nm
≥ 15 Nm
3
rd
phase
60
angular
displacement
1
4
3
2
M200661
Attachment bolts,
big-end bearing
caps
1
st
phase, sequence
1-2-3-4
35 Nm
2
nd
phase, sequence
4-3-2-1
45 Nm
3
rd
phase, sequence
1-2-3-4
60
angular
displacement
TECHNICAL DATA
9-4
©
200351
XE-engine lubrication system
0
ΧΦ65/75/85 series
2
9.3 FILLING CAPACITIES
Lubrication system
Total capacity, including oil cooler and oil filter
approx. 35 litres
Oil sump capacity, maximum level
approx. 30 litres
Oil pan capacity, minimum level
approx. 22 litres
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст