Honda Pilot (2019 year). Instruction — part 35
543
uu
When Driving
u
Shifting
Continued
Driving
Use the paddle shifters to change between 1st and 9th gears without removing your
hands from the steering wheel. The transmission will switch to the sequential mode.
■
When the transmission is in
(
D:
The vehicle will go into the sequential mode momentarily, and the sequential mode
gear selection indicator will come on.
Once you start traveling at a constant speed, the sequential mode will automatically
switch off, and the sequential mode gear selection indicator will go off.
Hold the
(
+ paddle shifter for two seconds or push
button to return to normal
drive.
■
When the transmission is in
(
S
The vehicle will go into the sequential mode, and the M (sequential mode) indicator
and sequential mode gear selection indicator will come on.
If the vehicle speed increases and the engine speed reaches near the tachometer’s
red zone, the transmission automatically shifts up to the next gear.
You can cancel this mode by holding the
(
+ paddle shifter for two seconds or push
button. When the sequential mode is canceled, the sequential mode indicator
and sequential mode gear selection indicator go off.
■
Sequential Mode
D/S
D/S
uu
When Driving
u
Shifting
544
Driving
■
Sequential Mode Operation
1
Each paddle shift operation makes a single gear
change.
To change gears continuously, release the paddle
shifter before pulling it again for the next gear.
If the sequential mode gear selection indicator blinks
when you try to shift up or down, this means your
vehicle speed is not in its allowable gear range or the
protection of transmission system is necessary.
Slightly accelerate to shift up and decelerate to shift
down while the indicator is blinking.
Sequential
Mode Gear
Selection
Indicator
Downshifting when pulling
the
paddle shifter.
(Changes to a lower gear)
Upshifting when pulling
the
paddle shifter.
(Changes to a higher gear)
Paddle Shifter
(Shift down)
Paddle Shifter
(Shift up)
545
uu
When Driving
u
Auto Idle Stop
*
Continued
Driving
Auto Idle Stop
*
To help maximize fuel economy, the engine automatically stops when the vehicle
comes to a stop, depending on environmental and vehicle operating conditions. The
indicator (green) comes on at this time.
The engine then restarts once the vehicle is
about to move again, or depending on
environmental and vehicle operating
conditions, and the indicator (green) goes off.
2 The Engine Automatically Restarts When
P. 548
A message associated with Auto Idle Stop
appears on the driver information interface.
2 Indicators P. 80
2 Customized Features P. 432
If the driver’s door is opened while the
indicator (green) comes on, a buzzer sounds
to notify you that the Auto Idle Stop function
is in operation.
1
The 12-volt battery installed in this vehicle is
specifically designed for a model with Auto Idle Stop.
Using a 12-volt battery other than this specified type
may shorten the 12-volt battery life, and prevent
Auto Idle Stop from activating. If you need to replace
the 12-volt battery, make sure to select the specified
type. Ask a dealer for more details.
The duration of the Auto Idle Stop operation:
•
Increases in the ECON mode, compared to when
the ECON mode is off, with climate control in use.
* Not available on all models
uu
When Driving
u
Auto Idle Stop
*
546
Driving
To turn the Auto Idle Stop system off, press
this button. The Auto Idle Stop system stops.
u
Auto Idle Stop system will stop and the
indicator (Amber) will come on.
The Auto Idle Stop system is turned on every
time you start the engine, even if you turned it
off the last time you drove the vehicle.
The vehicle stops with the gear position in
(
D and the brake pedal depressed.
When you put the transmission into
(
P, the Auto Idle Stop continues to operate,
even if the brake pedal is released.
u
If you change the gear position, the engine may automatically restarts.
■
Auto Idle Stop does not activate when:
• The Auto Idle Stop OFF button is pressed.
• The driver’s seat belt is not fastened.
• The engine coolant temperature is low or high.
• The transmission fluid temperature is low or high.
• The vehicle comes to a stop again before the vehicle speed reaches 3 mph (5
km/h) after the engine starts.
• Stopped on a steep incline.
• A gear position other than
(
D.
■
Auto Idle Stop System ON/OFF
1
Press the Auto Idle Stop OFF button to restart the
engine from the idling stop.
■
Auto Idle Stop Activates When:
1
Auto Idle Stop Activates When:
Do not open a hood, during idling stop. If the hood is
opened, the engine will not restart automatically.
In this case, restart the engine with the ENGINE
START/STOP button.
2 Starting the Engine P. 527
Pressing the ENGINE START/STOP button changes
the power mode to ACCESSORY even while Auto Idle
Stop is in operation. Once in ACCESSORY, the engine
no longer restarts automatically. Follow the standard
procedure to start the engine.
2 Starting the Engine P. 527
547
uu
When Driving
u
Auto Idle Stop
*
Continued
Driving
• The engine is started with the hood open.
u
Turn off the engine. Close the hood before you restart the engine to activate
Auto Idle Stop.
• The battery charge is low.
• The internal temperature of the battery is 14°F (−10°C) or less.
• The climate control system is in use, and the outside temperature is below −4°F
(−20°C) or over 104°F (40°C).
• The climate control system is in use, and the temperature is set to Hi or Lo.
•
is ON (indicator on).
• The rear fan is set to maximum speed.
u
Auto Idle Stop may not activate under other conditions when the rear climate
control system
*
/rear cooling
*
is in use.
• When the Intelligent Traction Management is set to Snow, Mud
*
, or Sand
*
.
■
Auto Idle Stop may not activate when:
• The vehicle is stopped by braking suddenly.
• The steering wheel is operated.
• The fan speed is high.
• Altitude is high.
• The vehicle is repeatedly accelerated and decelerated at a low speed.
• The climate control system is in use, and there is a significant difference between
the set temperature and the actual interior temperature.
• Humidity in the interior is high.
• The rear fan is set to maximum speed.
u
Auto Idle Stop may not activate under other conditions when the rear climate
control system
*
/rear cooling
*
is in use.
* Not available on all models
uu
When Driving
u
Auto Idle Stop
*
548
Driving
The brake pedal is released.
■
The engine restarts even if the brake pedal is depressed when:
• The Auto Idle Stop OFF button is pressed.
• When a steering wheel is operated.
• The transmission is put into
(
R or
(
S, or when it is set from
(
N to
(
D.
u
If you put the transmission into
(
P after the Auto Idle Stop activates, the Auto
Idle Stop continues to operate. In this case, the engine restarts when you
change the gear position other than
(
P. When changing the gear position, the
brake pedal must be firmly depressed.
• The pressure on the brake pedal is reduced and the vehicle starts moving while
stopped on an incline.
• The pressure on the brake pedal is repeatedly applied and released slightly during
a stop.
• The battery charge becomes low.
• The accelerator pedal is depressed.
• The driver’s seat belt is unlatched.
•
is ON (indicator on).
• The climate control system is in use, and the difference between the set
temperature and actual interior temperature becomes significant.
• The climate control system is being used to dehumidify the interior.
• The rear fan is set to maximum speed.
u
Auto Idle Stop may not activate under other conditions when the rear climate
control system is in use.
• When the Intelligent Traction Management is set to Snow, Mud
*
, or Sand
*
.
■
The Engine Automatically Restarts When
1
The Engine Automatically Restarts When
If you are using an electronic device during Auto Idle
Stop, the device may temporarily be turned off when
the engine restarts.
* Not available on all models
549
uu
When Driving
u
Auto Idle Stop
*
Driving
Briefly keeps the brake applied after releasing the brake pedal to restart the engine.
This can keep your vehicle from unexpectedly moving while on an incline.
■
Starting Assist Brake Function
550
uu
When Driving
u
ECON Mode
Driving
ECON Mode
The ECON button turns the ECON mode on
and off.
The ECON mode helps you improve your fuel
economy by adjusting the performance of the
engine, air conditioning system, and cruise
control.
1
While in ECON mode, the climate control system has
greater temperature fluctuations.
551
uu
When Driving
u
Intelligent Traction Management
*
Continued
Driving
Intelligent Traction Management
*
The Intelligent Traction Management optimizes vehicle performance to help you
drive on various surfaces. The system has available modes to select from: Normal,
Snow, Mud
*
, and Sand
*
.
Press the mode button to select the appropriate mode. The mode you select appears
on the driver information interface. When the vehicle is turned off and restarted,
Intelligent Traction Management mode will revert to Normal.
1
Intelligent Traction Management
Refer to the Off-Highway Driving section for driving
tips and safety precautions.
2 Off-Highway Driving Guidelines P. 525
Mud
Use when driving on
muddy road or off-
road surfaces.
Sand
Use when driving on
soft, sandy road or
off-road surfaces.
Normal
Provides balanced
driving performance
on most road surfaces.
Mode Button
Snow
Use when driving on
snowy road surfaces.
AWD models
* Not available on all models
552
uu
When Driving
u
Intelligent Traction Management
*
Driving
Normal
Provides balanced
driving performance
on most road surfaces.
Snow Button
Snow
Use when driving on
snowy road surfaces.
2WD models
553
uu
When Driving
u
Vehicle Stability Assist® (VSA®), aka Electronic Stability Control (ESC), System
Continued
Driving
Vehicle Stability Assist® (VSA®), aka Electronic
Stability Control (ESC), System
VSA® helps to stabilize the vehicle during cornering if the vehicle turns more or less
than what was intended. It also assists in maintaining traction on slippery surfaces.
It does so by regulating engine output and selectively applying the brakes.
When VSA® activates, you may notice that the
engine does not respond to the accelerator.
You may also notice some noise from the
hydraulic system. You will also see the
indicator blink.
■
VSA® Operation
1
Vehicle Stability Assist® (VSA®), aka Electronic Stability Control
(ESC), System
The VSA® may not function properly if tire type and
size are mixed. Make sure to use the same size and
type of tire, and the air pressures as specified.
When the VSA® system indicator comes on and stays
on while driving, there may be a problem with the
system. While this may not interfere with normal
driving, have your vehicle checked by a dealer
immediately.
VSA® cannot enhance stability in all driving situations
and does not control the entire braking system. You
still need to drive and corner at speeds appropriate
for the conditions and always leave a sufficient
margin of safety.
The main function of the VSA® system is generally
known as Electronic Stability Control (ESC). The
system also includes a traction control function.
VSA® System
Indicator
uu
When Driving
u
Vehicle Stability Assist® (VSA®), aka Electronic Stability Control (ESC), System
554
Driving
This button is on the driver side control panel.
To partially disable VSA® functionality/
features, press and hold it until you hear a
beep.
The traction control stops fully functioning,
allowing the wheels to spin more freely at low
speed. The VSA® OFF indicator will also come
on and a message on the driver information
interface informs you that the mode is
changed.
Traction control mode can not be changed
during Mud or Sand modes. If you are driving
on mud or sand, Mud or Sand Intelligent
Traction Management modes can also be
used to free a stuck vehicle. On other road
surfaces, change to Normal or Snow mode,
then press and hold the
(VSA® OFF) button.
To restore VSA® functionality/features, press
the
(VSA® OFF) button until you hear a
beep.
VSA® is turned on every time you start the
engine, even if you turned it off the last time
you drove the vehicle.
■
VSA® On and Off
1
Vehicle Stability Assist® (VSA®), aka Electronic Stability Control
(ESC), System
With the
button pressed, your vehicle will have
normal braking and cornering ability, but VSA®
traction and stability enhancement becomes less
effective.
In certain unusual conditions when your vehicle gets
stuck in shallow mud or fresh snow, it may be easier
to free it with the VSA® temporarily switched off.
When the
button is pressed, the traction control
function becomes less effective. This allows for the
wheels to spin more freely at low speed. You should
only attempt to free your vehicle with the VSA® off if
you are not able to free it when the VSA® is on.
Immediately after freeing your vehicle, be sure to
switch VSA® on again. We do not recommend driving
your vehicle with the VSA® system switched off.
You may hear a motor sound coming from the
engine compartment while system checks are being
performed immediately after starting the engine or
while driving. This is normal.
VSA® OFF Indicator
AWD models
555
uu
When Driving
u
Agile Handling Assist
Driving
Agile Handling Assist
Lightly brakes each of the front and rear wheels, as needed, when you turn the
steering wheel, and helps support the vehicle’s stability and performance during
cornering.
1
The agile handling assist cannot enhance stability in
all driving situations. You still need to drive and
corner at speeds appropriate for the conditions and
always leave a sufficient margin of safety.
When the VSA® system indicator comes on and stays
on while driving, the agile handling assist does not
activate.
You may hear a sound coming from the engine
compartment while the agile handling assist is
activated. This is normal.
556
uu
When Driving
u
Blind spot information System
*
Driving
Blind spot information System
*
Is designed to detect vehicles in specified alert zones adjacent to your vehicle,
particularly in harder to see areas commonly known as “blind spots”.
When the system detects vehicles approaching from behind in adjacent lanes, the
appropriate indicator comes on for a few seconds, providing assistance when you
change lanes.
■
How the system works
1
Important Safety Reminder
Like all assistance systems, blind spot information
system has limitations. Over reliance on blind spot
information system may result in a collision.
The system is for your convenience only. Even if an
object is within the alert zone, the following
situations may occur.
•
The blind spot information system alert indicator
may not come on due to obstruction (splashes,
etc.) even without the Blind Spot Info Not
Available driver information interface appearing.
•
The blind spot information system alert indicator
may come on even with the message appearing.
3
WARNING
Failure to visually confirm that it is safe to
change lanes before doing so may result in
a crash and serious injury or death.
Do not rely only on the blind spot
information system when changing lanes.
Always look in your mirrors, to either side
of your vehicle, and behind you for other
vehicles before changing lanes.
Alert zone range
A: Approx. 1.6 ft. (0.5 m)
B: Approx. 10 ft. (3 m)
C: Approx. 10 ft. (3 m)
Radar Sensors:
underneath the
rear bumper
corners
Alert Zone
A
B
C
●
The transmission is in
(
D.
●
Your vehicle speed is
between 20 mph (32 km/h)
and 100 mph (160 km/h)
* Not available on all models
Continued
557
uu
When Driving
u
Blind spot information System
*
Driving
■
When the system detects a vehicle
Blind spot information System Alert Indicator:
Located near the pillar on both sides.
Comes on when:
• A vehicle enters the alert zone from behind
to overtake you with a speed difference of
no more than 31 mph (50 km/h) from your
vehicle.
• You pass a vehicle with a speed difference
of no more than 12 mph (20 km/h).
Blinks and a beeper sounds when:
You move the turn signal lever in the direction
of the detected vehicle. The beeper sounds
three times.
1
The blind spot information system alert indicator may
not come on under the following conditions:
•
A vehicle does not stay in the alert zone for more
than two seconds.
•
A vehicle is parked in a side lane.
•
The speed difference between your vehicle and the
vehicle you are passing is greater than 6 mph
(10 km/h).
•
An object not detected by the radar sensors
approaches or passes your vehicle.
•
A vehicle running in the adjacent lane is a
motorcycle or other small vehicle.
The system does not operate when in
(
R.
You can turn off the audible alert, or all the blind spot
information system alert using the audio/information
screen.
2 Customized Features P. 432
Turn the system off when towing a trailer.
The system may not work properly for the following
reasons:
•
The added mass tilts the vehicle and changes the
radar coverage.
•
The trailer itself can be detected by the radar
sensors, causing the blind spot information system
alert indicators to come on.
Comes On
Blinks
* Not available on all models
uu
When Driving
u
Blind spot information System
*
558
Driving
1
Blind spot information system may be adversely
affected when:
•
Objects (guard rails, poles, trees, etc,.) are detected.
•
An object that does not reflect radio waves well,
such as a motorcycle, is in the alert zone.
•
Driving on a curved road.
•
A vehicle is moving from a far lane to the adjacent
lane.
•
The system picks up external electrical interference.
•
The rear bumper or the sensors have been improperly
repaired or the rear bumper has been deformed.
•
The orientation of the sensors has been changed.
•
In bad weather (Heavy rain, snow, and fog).
For a proper blind spot information system operation:
•
Always keep the rear bumper corner area clean.
•
Do not cover the rear bumper corner area with
labels or stickers of any kind.
•
Take your vehicle to a dealer if you need the rear
bumper corner area or the radar sensors to be repaired,
or the rear bumper corner area is strongly impacted.
* Not available on all models
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст