Honda Civic. Manual — part 48
YES -Faulty SRS unit or poor connection at SRS unit connector B (28P) and
the SRS unit. Check the connection; if the connection is OK, replace the SRS
unit (see SRS UNIT REPLACEMENT).
NO -Short to power in the floor wire harness; replace the floor wire harness.
DTC 21-9X ("X" CAN BE 0 THRU 9 OR A THRU F): SHORT TO GROUND IN DRIVER'S SEAT
BELT TENSIONER
Special Tools Required
SRS inflator simulator 07SAZ-TB4011A
SRS simulator lead K 070AZ-SNAA200
1. Clear the DTC memory (see CLEAR THE DTC MEMORY WITH THE
HDS).
2. Turn the ignition switch ON (II), and check that the SRS indicator comes on
for about 6 seconds and then goes off.
Does the SRS indicator stay on, and is DTC 21-9x indicated?
YES -Go to step 3.
NO -Intermittent failure, system is OK at this time. Go to
TROUBLESHOOTING INTERMITTENT FAILURES. If another DTC is
indicated, troubleshoot the DTC.
3. Turn the ignition switch OFF. Disconnect the negative cable from the battery,
then wait for 3 minutes.
4. Disconnect the floor wire harness 4P connector (A) from the driver's seat belt
tensioner.
NOTE:
Before doing this troubleshooting procedure, review SRS
Precautions and Procedures (see PRECAUTIONS AND
PROCEDURES) and General Troubleshooting Information
(see GENERAL TROUBLESHOOTING INFORMATION).
2008 Honda Civic EX
2006-08 RESTRAINTS SRS (Supplemental Restraint System) - Civic (Except Hybrid)
Fig. 96: Identifying Floor Wire Harness 4P Connector
Courtesy of AMERICAN HONDA MOTOR CO., INC.
5. Connect the SRS inflator simulator (2 ohms, connectors) and simulator lead K
to the floor wire harness.
6. Reconnect the negative cable to the battery.
7. Clear the DTC memory.
8. Read the DTC (see CLEAR THE DTC MEMORY WITH THE HDS).
Is DTC 21-9x indicated?
YES -Go to step 9.
NO -Short to ground in the driver's seat belt tensioner; replace the driver's seat
belt (see FRONT SEAT BELT REPLACEMENT ).
9. Turn the ignition switch OFF. Disconnect the negative cable from the battery,
then wait for 3 minutes.
10. Disconnect both seat belt buckle tensioner 4P connectors (see step 8
DISCONNECTING SYSTEM CONNECTORS) and the front passenger's
seat belt tensioner 4P connector (see step 7 DISCONNECTING SYSTEM
CONNECTORS).
11. Disconnect SRS unit connector B (28P) from the SRS unit (see step 9
DISCONNECTING SYSTEM CONNECTORS).
12. Disconnect the simulator lead from the floor wire harness.
2008 Honda Civic EX
2006-08 RESTRAINTS SRS (Supplemental Restraint System) - Civic (Except Hybrid)
13. Measure the resistance between the No. 1 terminal of SRS unit connector B
(28P) and body ground, and between the No. 2 terminal and body ground.
There should be an open circuit or at least 1 M ohms
Fig. 97: Measuring Resistance Between No. 1 Terminal Of SRS Unit
Connector B (28P) And Body Ground
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Is the resistance as specified?
YES -Faulty SRS unit or poor connection at SRS unit connector B (28P) and
the SRS unit. Check the connection; if the connection is OK, replace the SRS
unit (see SRS UNIT REPLACEMENT).
NO -Short to ground in the floor wire harness; replace the floor wire harness.
DTC 22-1X ("X" CAN BE 0 THRU 9 OR A THRU F): OPEN IN FRONT PASSENGER'S SEAT BELT
TENSIONER
Special Tools Required
SRS inflator simulator 07SAZ-TB4011A
SRS simulator lead K 070AZ-SNAA200
NOTE:
Before doing this troubleshooting procedure, review SRS
Precautions and Procedures (see PRECAUTIONS AND
PROCEDURES) and General Troubleshooting Information
(see GENERAL TROUBLESHOOTING INFORMATION).
2008 Honda Civic EX
2006-08 RESTRAINTS SRS (Supplemental Restraint System) - Civic (Except Hybrid)
1. Clear the DTC memory (see CLEAR THE DTC MEMORY WITH THE
HDS).
2. Turn the ignition switch ON (II), and check that the SRS indicator comes on
for about 6 seconds and then goes off.
Does the SRS indicator stay on, and is DTC 22-1x indicated?
YES -Go to step 3.
NO -Intermittent failure, system is OK at this time. Go to
TROUBLESHOOTING INTERMITTENT FAILURES. If another DTC is
indicated, troubleshoot the DTC.
3. Turn the ignition switch OFF. Disconnect the negative cable from the battery,
then wait for 3 minutes.
4. Disconnect the floor wire harness 4P connector (A) from the front passenger's
seat belt tensioner.
Fig. 98: Identifying Floor Wire Harness 4P Connector
Courtesy of AMERICAN HONDA MOTOR CO., INC.
5. Connect the SRS inflator simulator (2 ohms, connectors) and simulator lead K
to the floor wire harness.
6. Reconnect the negative cable to the battery.
7. Clear the DTC memory.
8. Read the DTC (see CLEAR THE DTC MEMORY WITH THE HDS).
2008 Honda Civic EX
2006-08 RESTRAINTS SRS (Supplemental Restraint System) - Civic (Except Hybrid)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст