Honda Civic. Manual — part 673
Fig. 63: Identifying Injector Control Module Relay
4. Connect injector control module relay 5P connector terminal No. 3 to body
ground with a jumper wire.
Fig. 64: Connecting Injector Control Module Relay 5P Connector
Terminal No. 3 To Body Ground With Jumper Wire
5. Jump the SCS line with the HDS.
6. Disconnect PCM connector A (44P).
7. Check for continuity between body ground and PCM connector terminal A15.
2008 Honda Civic GX
2006-08 ENGINE PERFORMANCE Fuel Supply System - Civic GX
Fig. 65: Checking Continuity Between Body Ground And PCM Connector
Terminal A15
Is there continuity?
YES -Go to step 8.
NO -Repair open in the wire between the injector control module relay and the
PCM (A15).
8. Measure voltage between injector control module relay 5P connector terminal
No. 1 and body ground.
Fig. 66: Measuring Voltage Between Injector Control Module Relay 5P
Connector Terminal No. 1 And Body Ground
Is there battery voltage?
YES -Go to step 9.
2008 Honda Civic GX
2006-08 ENGINE PERFORMANCE Fuel Supply System - Civic GX
NO -
Repair open in the wire between the injector control module relay and the
No. 5 +B INJ (15 A) fuse in the under-dash fuse/relay box. Also replace
the No. 5 +B INJ (15 A) fuse in the under-dash fuse/relay box.
Repair open in the wire between the No. 5 +B INJ (15 A) fuse in the
under-dash fuse/relay box and the No. 5 +B OP MAIN (80 A) fuse in the
under-hood fuse/relay box. Also replace the No. 5 +B OP MAIN (80 A)
fuse in the under-hood fuse/relay box.
If needed, replace the under-hood fuse/relay box, refer to the UNDER-
HOOD FUSE/RELAY BOX (ALL EXCEPT HYBRID) , or the under-
dash fuse/relay box, refer to the UNDER-DASH FUSE/RELAY BOX
(ALL EXCEPT HYBRID) .
9. Turn the ignition switch ON (II).
10. Measure voltage between injector control module relay 5P connector terminal
No. 5 and body ground.
Fig. 67: Measuring Voltage Between Injector Control Module Relay 5P
Connector Terminal No. 5 And Body Ground
Is there battery voltage?
YES -Go to step 11.
NO -Repair open in the wire between the injector control module relay and
PGM-FI main relay 1.
11. Turn the ignition switch OFF.
2008 Honda Civic GX
2006-08 ENGINE PERFORMANCE Fuel Supply System - Civic GX
12. Reconnect the injector control module relay and PCM connector A (44P).
13. Open the SCS line with the HDS.
14. Turn the ignition switch ON (II).
15. Measure voltage between injector control module relay 5P connector terminal
No. 2 and body ground.
Fig. 68: Measuring Voltage Between Injector Control Module Relay 5P
Connector Terminal No. 2 And Body Ground
Is there battery voltage?
YES -Repair open in the wire between the injector control module relay, the
injector control module, the injector, or the fuel shut-off solenoid valve relay.
NO -Go to step 16.
16. Test the injector control module relay (see POWER RELAY TEST ).
Is the injector control module relay OK?
YES -Update the PCM if it does not have the latest software (see UPDATING
THE PCM ), or substitute a known-good PCM (see SUBSTITUTING THE
PCM ), then recheck. If the symptom/indication goes away with a known-good
PCM, replace the original PCM, refer to the ECM/PCM REPLACEMENT .
NO -Replace the injector control module relay.
LEAK INSPECTION
2008 Honda Civic GX
2006-08 ENGINE PERFORMANCE Fuel Supply System - Civic GX
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст