Honda Civic. Manual — part 12
LIFT AND SUPPORT POINTS ).
2. Turn the appropriate wheel by hand.
APPROPRIATE WHEEL
Is there brake drag?
YES - Repair the brake drag.
NO - Go to step 3.
3. Check that the appropriate wheel sensor is properly mounted (see WHEEL
SENSOR REPLACEMENT ).
Is the wheel sensor installation OK?
YES - Intermittent failure, the system is OK at this time. Check for loose
terminals between the wheel sensor 2P connector and the ABS modulator-
control unit 25P connector. Refer to INTERMITTENT FAILURES
TROUBLESHOOTING . If the vehicle continues to code, replace the ABS
modulator-control unit: Except Si model (see REMOVAL - EXCEPT SI
MODEL ), Si model (see REMOVAL - SI MODEL ).
NO - Reinstall the wheel sensor, and check the mounting position (see
WHEEL SENSOR REPLACEMENT ).
DTC 51-11: MOTOR LOCK; DTC 51-13: MOTOR RELAY OFF MALFUNCTION
1. Turn the ignition switch ON (II).
2. Clear the DTC with the HDS.
3. Turn the ignition switch to LOCK (0), then turn it ON (II) again.
DTC Appropriate Wheel
41-21
Right-front
42-21
Left-front
43-21
Right-rear
44-21
Left-rear
2008 Honda Civic GX
2006-08 BRAKES ABS System - Civic (All Except Hybrid)
4. Wait 5 seconds.
5. Operate each SOLENOID in the ABS FUNCTION TEST five times with the
HDS.
6. Check for DTCs with the HDS.
Is DTC 51-11 or 51-13 indicated?
YES - Replace the ABS modulator-control unit: Except Si model (see
REMOVAL - EXCEPT SI MODEL ), Si model (see REMOVAL - SI
MODEL ).
NO - Intermittent failure, the system is OK at this time.
DTC 51-12: MOTOR LOCK CIRCUIT MALFUNCTION
1. Turn the ignition switch ON (II).
2. Clear the DTC with the HDS.
3. Turn the ignition switch to LOCK (0), then turn it ON (II) again.
4. Check for DTCs with the HDS.
Is DTC 51-12 indicated?
YES - Go to step 5.
NO - Intermittent failure, the system is OK at this time. Check for loose
terminals at the ABS modulator-control unit 25P connector. Refer to
INTERMITTENT FAILURES TROUBLESHOOTING .
5. Turn the ignition switch to LOCK (0).
6. Check the No. 3 MTR (30 A) fuse in the under-hood fuse/relay box.
Is the fuse blown?
YES - Go to step 7.
NO - Reinstall the checked fuse, then go to step 9.
2008 Honda Civic GX
2006-08 BRAKES ABS System - Civic (All Except Hybrid)
7. Disconnect the ABS modulator-control unit 25P connector.
8. Check for continuity between ABS modulator-control unit 25P connector
terminal No. 9 and body ground.
Fig. 20: Checking Continuity Between ABS Modulator-Control Unit 25P
Connector Terminal No. 9 And Body Ground
Is there continuity?
YES - Repair short to body ground in the wire between the No. 3 MTR (30 A)
fuse in the understood fuse/relay box and the ABS modulator-control unit.
NO - Install a new No. 3 MTR (30 A) fuse in the under-hood fuse/relay box,
then go to step 10.
9. Disconnect the ABS modulator-control unit 25P connector.
10. Measure voltage between ABS modulator-control unit 25P connector terminal
No. 9 and body ground.
Fig. 21: Measuring Voltage Between ABS Modulator-Control Unit 25P
2008 Honda Civic GX
2006-08 BRAKES ABS System - Civic (All Except Hybrid)
Connector Terminal No. 9 And Body Ground
Is there battery voltage?
YES - Check for loose terminals in the ABS modulator-control unit 25P
connector. If necessary, substitute a known-good ABS modulator-control unit:
Except Si model (see REMOVAL - EXCEPT SI MODEL ), Si model (see
REMOVAL - SI MODEL ), and retest.
NO - Repair open in the wire between the No. 3 MTR (30 A) fuse in the under-
hood fuse/relay box and the ABS modulator-control unit.
DTC 52-12: MOTOR STUCK OFF
1. Turn the ignition switch ON (II).
2. Clear the DTC with the HDS.
3. Turn the ignition switch to LOCK (0), then turn it ON (II) again.
4. Operate each SOLENOID in the ABS FUNCTION TEST five times with the
HDS.
5. Check for DTCs with the HDS.
Is DTC 52-12 indicated?
YES - Replace the ABS modulator-control unit: Except Si model (see
REMOVAL - EXCEPT SI MODEL ), Si model (see REMOVAL - SI
MODEL ).
NO - Intermittent failure, the system is OK at this time.
DTC 53-01: MOTOR RELAY STUCK ON 1; DTC 53-12: MOTOR RELAY STUCK ON 2
1. Turn the ignition switch ON (II).
2. Clear the DTC with the HDS.
3. Turn the ignition switch to LOCK (0), then turn it ON (II) again.
4. Check for DTCs with the HDS.
Is DTC 53-01 or 53-12 indicated?
2008 Honda Civic GX
2006-08 BRAKES ABS System - Civic (All Except Hybrid)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст