Honda Civic. Manual — part 220
4. Check for DTCs with the HDS.
Is DTC P0970 indicated?
YES -Go to step 8.
NO -Go to step 5.
5. Select Clutch Pressure Control Solenoid Valve C in the Miscellaneous Test
Menu, and test A/T clutch pressure control solenoid valve C with the HDS.
Does the HDS indicate NORMAL?
YES -Go to step 6.
NO -Go to step 8.
6. In the Clutch Pressure Control Solenoid Valve Control menu, select A/T clutch
pressure control solenoid valve C at 1.0 A.
7. Monitor the OBD STATUS for P0970 in the DTCs MENU with the HDS.
Does the HDS indicate FAILED?
YES -Go to step 8.
NO -If the HDS indicates PASSED, intermittent failure, the system is OK at
this time. Check for poor connections or loose terminals between A/T clutch
pressure control solenoid valve C and the PCM. If the HDS indicates NOT
COMPLETED, go to step 5.
8. Turn the ignition switch OFF.
9. Disconnect the A/T clutch pressure control solenoid valve C connector.
10. Measure the resistance between A/T clutch pressure control solenoid valve C
connector terminals No. 1 and No. 2.
2008 Honda Civic LX
2006-08 TRANSMISSION Automatic Transmission - Civic (Except Hybrid)
![](/vehicles/vescileif/dedas/weaveng/xeayeroumy.png)
Fig. 139: Measuring Resistance Between A/T Clutch Pressure Control
Solenoid Valve C Terminals 1 And 2
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Is there 3-10 ohms?
YES -Go to step 11.
NO -Replace A/T clutch pressure control solenoid valve C (see A/T CLUTCH
PRESSURE CONTROL SOLENOID VALVE B AND C
REPLACEMENT ), then go to step 16.
11. Check for continuity between A/T clutch pressure control solenoid valve C
connector terminal No. 2 and body ground.
Fig. 140: Checking Continuity Between A/T Clutch Pressure Control
Solenoid Valve C Terminal 2 And Body Ground
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Is there continuity?
2008 Honda Civic LX
2006-08 TRANSMISSION Automatic Transmission - Civic (Except Hybrid)
![](/vehicles/vescileif/dedas/weaveng/juan.png)
YES -Go to step 12.
NO -Repair open in the wire between A/T clutch pressure control solenoid
valve C and ground (G101) (see CONNECTOR TO HARNESS INDEX ), or
repair poor ground (G101), then go to step 16.
12. Jump the SCS line with the HDS.
13. Disconnect PCM connector B (44P).
14. Check for continuity between A/T clutch pressure control solenoid valve C
connector terminal No. 1 and body ground.
Fig. 141: Checking Continuity Between A/T Clutch Pressure Control
Solenoid Valve C Terminal 1 And Body Ground
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Is there continuity?
YES -Repair short to body ground in the wire between A/T clutch pressure
control solenoid valve C connector terminal No. 1 and body ground, then go to
step 16.
NO -Go to step 15.
15. Check for continuity between A/T clutch pressure control solenoid valve C
connector terminal No. 1 and PCM connector terminal B25.
2008 Honda Civic LX
2006-08 TRANSMISSION Automatic Transmission - Civic (Except Hybrid)
![](/vehicles/vescileif/dedas/weaveng/toruslane.png)
Fig. 142: Checking Continuity Between A/T Clutch Pressure Control
Solenoid Valve C Terminal 1 And PCM Connector Terminal B25
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Is there continuity?
YES -Go to step 22.
NO -Repair open in the wire between A/T clutch pressure control solenoid
valve C connector terminal No. 1 and PCM connector terminal B25, then go to
step 16.
16. Reconnect all connectors.
17. Turn the ignition switch to ON (II).
18. Clear the DTC with the HDS.
19. Start the engine, and wait for at least 1 second.
20. Check for DTCs with the HDS.
Is DTC P0970 indicated?
YES -Check for poor connections or loose terminals between A/T clutch
pressure control solenoid valve C and the PCM, then go to step 1.
NO -Go to step 21.
21. Monitor the OBD STATUS for P0970 in the DTCs MENU with the HDS.
Does the HDS indicate PASSED?
2008 Honda Civic LX
2006-08 TRANSMISSION Automatic Transmission - Civic (Except Hybrid)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст