Honda Civic. Manual — part 215

23. Update the PCM if it does not have the latest software (see UPDATING THE

PCM ), or substitute a known-good PCM (see SUBSTITUTING THE
PCM ).

24. Start the engine, and warm it up to normal operating temperature (the radiator

fan comes on).

25. Test-drive the vehicle in 3rd gear with the shift lever in D3, for at least 2

seconds. Then shift to D, and drive in 4th gear for at least 2 seconds.

26. Check for DTCs with the HDS.

Is DTC P0848 indicated?

YES -Check for poor connections or loose terminals between the 3rd clutch
transmission fluid pressure switch and the PCM. If the PCM was updated,
substitute a known-good PCM (see SUBSTITUTING THE PCM ), then go to
step 24. If the PCM was substituted, go to step 1.

NO -Go to step 27.

27. Monitor the OBD STATUS for P0848 in the DTCs MENU with the HDS.

Does the HDS indicate PASSED?

YES -If the PCM was updated, troubleshooting is complete. If the PCM was
substituted, replace the original PCM (see ECM/PCM REPLACEMENT ). If
any other DTCs were indicated in step 26, go to the INDICATED DTC'S
TROUBLESHOOTING.

NO -If the HDS indicates FAILED, check for poor connections or loose
terminals between the 3rd clutch transmission fluid pressure switch and the
PCM. If the PCM was updated, substitute a known-good PCM (see
SUBSTITUTING THE PCM ), then go to step 24. If the PCM was
substituted, go to step 1. If the HDS indicates NOT COMPLETED, go to step
24.

DTC P0962: Problem in A/T Clutch Pressure Control Solenoid Valve A Circuit

NOTE:

2008 Honda Civic LX

2006-08 TRANSMISSION Automatic Transmission - Civic (Except Hybrid)

1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Start the engine, and wait for at least 1 second.
4. Check for DTCs with the HDS.

Is DTC P0962 indicated?

YES -Go to step 8.

NO -Go to step 5.

5. Select Clutch Pressure Control Solenoid Valve A in the Miscellaneous Test

Menu, and test A/T clutch pressure control solenoid valve A with the HDS.

Does the HDS indicate NORMAL?

YES -Go to step 6.

NO -Go to step 8.

6. In the Clutch Pressure Control Solenoid Valve Control menu, select A/T clutch

pressure control solenoid valve A at 1.0 A.

7. Monitor the OBD STATUS for P0962 in the DTCs MENU with the HDS.

Does the HDS indicate FAILED?

YES -Go to step 8.

Before you troubleshoot, record all freeze data and any
on-board snapshot with the HDS, and review General
Troubleshooting Information (see GENERAL
TROUBLESHOOTING INFORMATION ).

This code is caused by an electrical circuit problem and
cannot be caused by a mechanical problem in the
transmission.

2008 Honda Civic LX

2006-08 TRANSMISSION Automatic Transmission - Civic (Except Hybrid)

NO -If the HDS indicates PASSED, intermittent failure, the system is OK at
this time. Check for poor connections or loose terminals between A/T clutch
pressure control solenoid valve A and the PCM. If the HDS indicates NOT
COMPLETED, go to step 5.

8. Turn the ignition switch to LOCK (0).
9. Disconnect the A/T clutch pressure control solenoid valve A connector.

10. Measure the resistance between A/T clutch pressure control solenoid valve A

connector terminals No. 1 and No. 2.

Fig. 127: Measuring Resistance Between A/T Clutch Pressure Control
Solenoid Valve A Connector Terminals 1 And 2
Courtesy of AMERICAN HONDA MOTOR CO., INC.

Is there 3-10 ohms?

YES -Go to step 11.

NO -Replace A/T clutch pressure control solenoid valve A (see A/T CLUTCH
PRESSURE CONTROL SOLENOID VALVE A REPLACEMENT ), then
go to step 16.

11. Check for continuity between A/T clutch pressure control solenoid valve A

connector terminal No. 2 and body ground.

2008 Honda Civic LX

2006-08 TRANSMISSION Automatic Transmission - Civic (Except Hybrid)

Fig. 128: Checking Continuity Between A/T Clutch Pressure Control
Solenoid Valve A Connector Terminal 2 And Body Ground
Courtesy of AMERICAN HONDA MOTOR CO., INC.

Is there continuity?

YES -Go to step 12.

NO -Repair open in the wire between A/T clutch pressure control solenoid
valve A and ground (G101) (see CONNECTOR TO HARNESS INDEX ), or
repair poor ground (G101), then go to step 16.

12. Jump the SCS line with the HDS.
13. Disconnect PCM connector B (44P).
14. Check for continuity between A/T clutch pressure control solenoid valve A

connector terminal No. 1 and body ground.

Fig. 129: Checking Continuity Between A/T Clutch Pressure Control
Solenoid Valve A Connector Terminal 1 And Body Ground
Courtesy of AMERICAN HONDA MOTOR CO., INC.

2008 Honda Civic LX

2006-08 TRANSMISSION Automatic Transmission - Civic (Except Hybrid)