Honda Civic. Manual — part 1088
NO -Replace the steering angle sensor (see STEERING ANGLE SENSOR
REPLACEMENT ).
DTC 27-23: STEERING ANGLE SENSOR COUNTER MALFUNCTION
1. Turn the ignition switch ON (II).
2. Clear the DTC with the HDS.
3. Turn the ignition switch to LOCK (0), then turn it ON (II) again.
4. Turn the steering wheel from lock to lock.
5. Check for DTCs with the HDS.
Is DTC 27-23 indicated?
YES -Replace the steering angle sensor (see STEERING ANGLE SENSOR
REPLACEMENT ).
NO -Intermittent failure, the system is OK at this time.
DTC 27-24: STEERING ANGLE SENSOR EXCHANGE MALFUNCTION
1. Turn the ignition switch ON (II).
2. Turn the steering wheel 1 turn. Check the STEERING ANGLE in the VSA
DATA LIST with the HDS.
Is there about 288-432 °?
YES -Intermittent failure, the system is OK at this time.
NO -Replace the steering angle sensor (see STEERING ANGLE SENSOR
REPLACEMENT ).
DTC 31-XX*: ABS RIGHT-FRONT INLET SOLENOID VALVE MALFUNCTION; DTC 32-
XX*: ABS
RIGHT-FRONT OUTLET SOLENOID VALVE MALFUNCTION; DTC 33-XX*: ABS LEFT-FRONT
INLET SOLENOID VALVE MALFUNCTION; DTC 34-XX*: ABS LEFT-FRONT OUTLET
SOLENOID VALVE MALFUNCTION; DTC 35-XX*: ABS RIGHT-REAR INLET SOLENOID
VALVE MALFUNCTION; DTC 36-XX*: ABS RIGHT-REAR OUTLET SOLENOID VALVE
MALFUNCTION; DTC 37-XX*: ABS LEFT-REAR INLET SOLENOID VALVE MALFUNCTION;
DTC 38-XX*: ABS LEFT-REAR OUTLET SOLENOID VALVE MALFUNCTION
2008 Honda Civic GX
2006-08 BRAKES VSA System - Civic (All Except Hybrid)
*: Subcode
1. Turn the ignition switch ON (II).
2. Clear the DTC with the HDS.
3. Turn the ignition switch to LOCK (0), then turn it ON (II) again.
4. Check for DTCs with the HDS.
DTC REFERENCE
Is DTC 31-xx, 32-xx, 33-xx, 34-xx, 35-xx, 36-xx, 37-xx, or 38-xx indicated?
YES -Replace the VSA modulator-control unit (see VSA MODULATOR-
CONTROL UNIT REMOVAL AND INSTALLATION ).
NO -Intermittent failure, the system is OK at this time.
DTC 41-21: RIGHT-FRONT WHEEL LOCK; DTC 42-21: LEFT-FRONT WHEEL LOCK; DTC 43-
21:
RIGHT-REAR WHEEL LOCK; DTC 44-21: LEFT-REAR WHEEL LOCK
The DTCs may be indicated under these conditions:
The vehicle goes into a spin.
The ABS or VSA continues to operate for a long time.
Snow build-up on the wheel speed sensor.
Misadjusted brake switch.
Contaminated brake fluid.
Subcode
Malfunction
Note (DTC)
01
Solenoid Initial
Pulse
31-01, 32-01, 33-01, 34-01, 35-01, 36-01, 37-
01, 38-01
21
Solenoid Pulse
31-21, 32-21, 33-21, 34-21, 35-21, 36-21, 37-
21, 38-21
22
Solenoid
Speculative
31-22, 32-22, 33-22, 34-22, 35-22, 36-22, 37-
22, 38-22
23
Solenoid Stuck ON
31-23, 32-23, 33-23, 34-23, 35-23, 36-23, 37-
23, 38-23
2008 Honda Civic GX
2006-08 BRAKES VSA System - Civic (All Except Hybrid)
1. Raise the vehicle, and support it with safety stands in the proper locations (see
LIFT AND SUPPORT POINTS ).
2. Turn the appropriate wheel by hand.
DTC REFERENCE
Is there brake drag?
YES -Repair the brake drag.
NO -Go to step 3.
3. Check the appropriate wheel speed sensor is properly mounted (see WHEEL
SPEED SENSOR REPLACEMENT ).
Is the wheel speed sensor installation OK?
YES -Intermittent failure, the system is OK at this time. Check for loose
terminals between the wheel speed sensor 2P connector and the VSA
modulator-control unit 37P connector. Refer to INTERMITTENT
FAILURES TROUBLESHOOTING (see ). If the vehicle continues to code,
replace the VSA modulator-control unit (see VSA MODULATOR-
CONTROL UNIT REMOVAL AND INSTALLATION ).
NO -Reinstall the wheel speed sensor, and check the mounting position (see
WHEEL SPEED SENSOR REPLACEMENT ).
DTC 51-11: MOTOR LOCK; DTC 51-13: MOTOR RELAY OFF MALFUNCTION
1. Turn the ignition switch ON (II).
2. Clear the DTC with the HDS.
DTC Appropriate Wheel
41-21
Right-front
42-21
Left-front
43-21
Right-rear
44-21
Left-rear
2008 Honda Civic GX
2006-08 BRAKES VSA System - Civic (All Except Hybrid)
3. Turn the ignition switch to LOCK (0), then turn it ON (II) again.
4. Wait 5 seconds.
5. Operate SOLENOID or VSA in the VSA FUNCTION TEST five times with
the HDS.
6. Check for DTCs with the HDS.
Is DTC 51-11 or 51-13 indicated?
YES -Replace the VSA modulator-control unit (see VSA MODULATOR-
CONTROL UNIT REMOVAL AND INSTALLATION ).
NO -Intermittent failure, the system is OK at this time.
DTC 51-12: MOTOR LOCK CIRCUIT MALFUNCTION
1. Turn the ignition switch ON (II).
2. Clear the DTC with the HDS.
3. Turn the ignition switch to LOCK (0), then turn it ON (II) again.
4. Check the DTCs with the HDS.
Is DTC 51-12 indicated?
YES -Go to step 5.
NO -Intermittent failure, the system is OK at this time. Check for loose
terminals at the VSA modulator-control unit 37P connector. Refer to
INTERMITTENT FAILURES TROUBLESHOOTING (see ).
5. Turn the ignition switch to LOCK (0).
6. Check the No. 3 MTR (30 A) fuse in the under-hood fuse/relay box.
Is the fuse blown?
YES -Go to step 7.
NO -Reinstall the checked fuse, then go to step 9.
2008 Honda Civic GX
2006-08 BRAKES VSA System - Civic (All Except Hybrid)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст