Honda Civic. Manual — part 110
Fig. 344: Identifying Gap Between Spring Washer And Seat Track
Courtesy of AMERICAN HONDA MOTOR CO., INC.
6. Reassemble the front passenger's seat cushion cover/pad (see FRONT SEAT
CUSHION COVER REPLACEMENT ).
7. Reinstall the front passenger's seat (see FRONT SEAT
REMOVAL/INSTALLATION ).
8. Reconnect the negative cable to the battery.
9. Calibrate the ODS unit (see ODS UNIT CALIBRATION).
10. After installing the front passenger's weight sensors, confirm proper system
operation: Turn the ignition switch ON (II); the SRS indicator should come for
about 6 seconds and then go off.
Special Tools Required
Pin driver, 3.5 mm 07744-0010300
2-DOOR
Removal
1. Disconnect the negative cable from the battery, then wait for 3 minutes before
NOTE:
Removal of the front passenger's weight sensors must be
done according to Precautions and Procedures (see
PRECAUTIONS AND PROCEDURES).
2008 Honda Civic EX
2006-08 RESTRAINTS SRS (Supplemental Restraint System) - Civic (Except Hybrid)
starting work.
2. Remove the front passenger's seat assembly (see FRONT SEAT
REMOVAL/INSTALLATION ).
3. Remove the cushion cover/pad from the seat cushion frame (see FRONT
SEAT CUSHION COVER REPLACEMENT ).
4. Using a TORX T27 bit, remove the tamper-resistant TORX bolts (A) that
attach the seat track (B) to the weight sensors (C).
Fig. 345: Identifying Front Passenger's Weight Sensor, Seat Track And
Torx Bolts
Courtesy of AMERICAN HONDA MOTOR CO., INC.
5. Disconnect the sensor connectors (D) from the ODS unit harness, then remove
the front passenger's weight sensors.
Installation
1. Install the new front passenger's weight sensors with tamper-resistant TORX
bolts (C) under the seat track.
NOTE:
Be sure to install the harness wires so they are not
pinched or interfere with other parts.
Make sure both of the hooks (A) on the seat track are
properly secured to the front bracket (B). If the hooks
are not properly secured, the seat weight sensors will
not function properly.
2008 Honda Civic EX
2006-08 RESTRAINTS SRS (Supplemental Restraint System) - Civic (Except Hybrid)
Fig. 346: Identifying Front Bracket, Hooks And Tamper-Resistant With
Torque Specification
Courtesy of AMERICAN HONDA MOTOR CO., INC.
2. Reassemble the front passenger's seat cushion cover/pad (see FRONT SEAT
CUSHION COVER REPLACEMENT ).
3. Reinstall the front passenger's seat (see FRONT SEAT
REMOVAL/INSTALLATION ).
4. Reconnect the negative cable to the battery.
5. Calibrate the ODS unit (see ODS UNIT CALIBRATION).
6. After installing the front passenger's weight sensors, confirm proper system
operation: Turn the ignition switch ON (II); the SRS indicator should come ON
for about 6 seconds and then go off.
ODS UNIT REPLACEMENT
REMOVAL
1. Disconnect the negative cable from the battery, then wait for 3 minutes before
starting work.
2. Disconnect the passenger's side airbag 2P connector (see step 3
NOTE:
Review the seat replacement procedure (see FRONT SEAT
REMOVAL/INSTALLATION ) before doing repairs or service.
2008 Honda Civic EX
2006-08 RESTRAINTS SRS (Supplemental Restraint System) - Civic (Except Hybrid)
DISCONNECTING SYSTEM CONNECTORS).
3. Remove the passenger's seat assembly (see FRONT SEAT
REMOVAL/INSTALLATION ) and seat-back cover (see FRONT SEAT-
BACK COVER REPLACEMENT ).
4. Disconnect the ODS unit 18P connector (A) and sensor connectors (B) from
the ODS unit (C).
Fig. 347: Identifying ODS Unit, 18P Connector And Nuts
Courtesy of AMERICAN HONDA MOTOR CO., INC.
5. Remove the two nuts (D) and the ODS unit.
INSTALLATION
1. Place the ODS unit (A) on the seat-back frame. Tighten the two nuts (B), and
connect the ODS unit harness 18P connector (C) and sensor connectors (D) to
the ODS unit.
2008 Honda Civic EX
2006-08 RESTRAINTS SRS (Supplemental Restraint System) - Civic (Except Hybrid)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст