Honda Odyssey (2019 year). Instruction — part 35
544
uu
When Driving
u
Precautions While Driving
Driving
Precautions While Driving
Avoid driving in deep water and on flooded roads. This can damage the engine or
driveline, or cause electrical component failure.
If there is a strong impact with something under the vehicle, stop in a safe location.
Check the underside of the vehicle for damage or any fluid leaks.
■
In Rain
■
Other Precautions
1
NOTICE
Do not change the gear position while pressing the
accelerator pedal. You could damage the
transmission.
NOTICE
If you repeatedly turn the steering wheel at an
extremely low speed, or hold the steering wheel in
the full left or right position for a while, the electric
power steering (EPS) system heats up. The system
goes into a protective mode, and limits its
performance. The steering wheel becomes harder
and harder to operate. Once the system cools down,
the EPS system is restored.
Repeated operation under these conditions can
eventually damage the system.
If the power mode is set to ACCESSORY while
driving, the engine will shut down and all steering
and brake power assist functions will stop, making it
difficult to control the vehicle.
Do not change the gear position to
(
N, as you will
lose engine braking (and acceleration) performance.
During the first 600 miles (1,000 km) of operation,
avoid sudden acceleration or full throttle operation so
as not to damage the engine or powertrain.
Avoid hard braking for the first 200 miles (300 km).
You should also follow this when the brake pads are
replaced.
545
uu
When Driving
u
Automatic Transmission
Driving
Automatic Transmission
The engine runs at a higher idle speed and creeping increases.
Keep the brake pedal firmly depressed when stopped.
Quickly depressing the accelerator pedal while driving uphill may cause the
transmission to drop to a lower gear, unexpectedly increasing vehicle speed. Depress
the accelerator pedal carefully, especially on slippery roads and curves.
■
Creeping
■
Kickdown
546
uu
When Driving
u
Shifting
Driving
Shifting
Change the gear position in accordance with your driving needs.
■
Shift button positions
1
To prevent malfunction and unintended
engagement:
•
Do not spill any liquids on or around shift buttons.
•
Do not place or drop any objects on or around shift
buttons.
•
Do not let passengers or children operate the shift
buttons.
The beeper sounds when you depress the accelerator
pedal with the gear position in
(
N.
Change the gear position to
(
D or
(
R with the brake
pedal depressed.
When shifting gears in extremely low temperatures
(−22°F/−30°C), there may be a short delay before the
shift is indicated in the display. Always confirm you
are in the correct gear before driving.
3
WARNING
The vehicle can roll away if left unattended
without confirming that Park is engaged.
A vehicle that rolls away could cause a crash
resulting in serious injury or death.
Always keep your foot on the brake pedal
until you have confirmed that
(
P
is shown
on the gear position indicator.
Park
Used when parking or starting the engine
Transmission is locked
Reverse
Used when reversing
Neutral
Transmission is not locked
Drive/S Position
Each time you press the
button, the mode
switches between Drive and S Position mode.
Used for:
●
Normal driving (gears change between1st and
9th automatically)
●
Normal driving (gears change between1st and
10th automatically)
●
Temporarily driving in the sequential mode
D/S
Drive
Except ELITE and TOURING grade models
ELITE and TOURING grade models
All models
●
Automatically changing gears between 1st and
7th (7th gear is used only at high speed)
●
Automatically changing gears between 1st and
8th (8th gear is used only at high speed)
●
Driving in the sequential mode
S Position
Except ELITE and TOURING grade models
ELITE and TOURING grade models
All models
547
uu
When Driving
u
Shifting
Continued
Driving
■
(
P (park) button
Park your vehicle in a safe place with the
power mode in ON, then apply the brakes and
press the
(
P button to put the transmission in
Park.
The indicators on the sides of the
(
P button
come on.
(
P Button
uu
When Driving
u
Shifting
548
Driving
■
Shift Operation
1
NOTICE
When you change
(
D to
(
R and visa versa, depress
the brake pedal to come to a complete stop, then
select the intended gear position while maintaining
brake pressure.
Use the gear position indicator and the shift button
indicator to check the gear position before selecting
a shift button.
If the indicator of the currently selected gear position,
or all the gear position indicators are blinking
simultaneously, there is a problem with the
transmission.
Avoid sudden acceleration and have the transmission
checked by a dealer as soon as possible.
The fuel supply may be cut off if you drive at engine
speeds in or over the tachometer’s red zone (engine
speed limit). If this happens, you may experience a
slight jolt.
When the engine speed is increased while the
transmission is in
(
N,
(
P or
(
R, the fuel supply may
be cut off even without the engine speed entering
the tachometer’s red zone.
The beeper sounds once when you change to
(
R.
2 Vehicle Customization P. 133
2 Customized Features P. 443
Models with color audio system
Models with Display Audio
Press the
(
P button.
Pull back the
(
R button.
Press the
(
N button.
Press the
button.
Each time you press the button, the
mode switches between Drive and S
Position mode.
D/S
Shift Button
Indicator
M (sequential mode) Indicator
Tachometer’s red zone
Sequential Mode Gear Selection
Indicator
Gear Position Indicator
Continued
549
uu
When Driving
u
Shifting
Driving
In freezing or sub-freezing conditions, the gear selection response may be slow.
Always depress the brake pedal before changing the gear position to
(
P, and
confirm that
(
P is shown on the gear position indicator before releasing the brake.
■
When opening the driver’s door
If you open the driver’s door under the following conditions, the gear position
automatically changes to
(
P;
• The vehicle is stationary with the engine running, or moving at 1 mph (2 km/h) or
slower.
• The transmission is in other than
(
P.
• You have unfastened the driver side seat belt.
u
If you manually change the gear position from
(
P with the brake pedal
depressed, the gear position will automatically return to
(
P once you release
the brake pedal.
■
When turning off the power mode
If you turn the engine off while the vehicle is stationary, and the transmission is in
other than
(
P, the gear position automatically changes to
(
P.
Except ELITE and TOURING grade models
1
When opening the driver’s door
You should always select
(
P before opening the
driver’s door.
Make sure to park the vehicle in a safe place.
If you want to drive the vehicle after the gear position
has automatically changed to
(
P under the described
conditions, close the door, fasten the seat belt,
depress the brake pedal, then change the gear
position.
If you leave the vehicle, turn off the engine and lock
the doors.
uu
When Driving
u
Shifting
550
Driving
■
If you want to keep the transmission in
(
N position [car wash mode]
With the engine running:
1. Press and hold the brake pedal.
2. Select
(
N, then release the button to display (Neutral)
(
N hold mode on the driver
information interface.
3. Press and hold
(
N again for two seconds.
u
This puts the vehicle in car wash mode which must be used when your vehicle
is pulled through a conveyor type automatic car wash where you or an
attendant do not remain in the vehicle.
If the ENGINE STOP/START button is pressed
after car wash mode has been activated, the
power mode will change to ACCESSORY and
a message will be displayed on the driver
information interface.
u
For 15 minutes the gear position remains
in
(
N with the power mode in
ACCESSORY. After that, the position
automatically changes to
(
P and the
power mode changes to OFF.
u
Manually changing to
(
P cancels
ACCESSORY mode. The
(
P indicator
comes on and the power mode changes
to OFF. You must always shift to
(
P
when car wash mode is no longer
needed.
1
If you want to keep the transmission in
(
N position [car wash
mode]
NOTICE
When transmission is too hot, carwash mode may
not be available. Let the engine idle and cool down
transmission.
The transmission may not stay in
(
N position while
the following indicator is on:
•
Transmission system indicator.
•
Malfunction indicator lamp.
•
Charging system indicator.
ELITE and TOURING grade models
551
uu
When Driving
u
Shifting
Continued
Driving
■
Restriction on selecting a gear position
You cannot select a gear position under certain circumstances that may lead to a crash.
When the transmission
is in:
1. Under the
circumstances of that:
2. You cannot select:
3. The gear position
remains in/changes to:
How to change
the gear position
(
P
The brake pedal is not
depressed.
Other gear position
(
P
Release the
accelerator pedal
and depress the
brake pedal.
The accelerator pedal is
depressed.
(
N
The vehicle is moving at
low speed without the
brake pedal depressed.
(
N
The vehicle is moving at
low speed with the
accelerator pedal
depressed.
(
N
, (
D
or (
S
The vehicle is moving
forward.
(
R
Stop your vehicle in
a safe place, depress
the brake pedal, and
select the
appropriate gear
position.
(
R
or (
N
The vehicle is moving
backward.
(
D,
(
S
(
R
, (
N
, (
D
or (
S
The vehicle is moving.
(
P
552
uu
When Driving
u
Shifting
Driving
Use the paddle shifters to change between 1st and 9th
*
or 10th
*
gears without
removing your hands from the steering wheel. The transmission will switch to the
sequential mode.
■
When the transmission is in
(
D:
The vehicle will go into the sequential mode momentarily, and the sequential mode
gear selection indicator will come on.
When the vehicle goes into the sequential mode by
(
- paddle shifter and the lower
gear is available, the transmission properly selects single or double gear change.
Once you start traveling at a constant speed, the sequential mode will automatically
switch off, and the sequential mode gear selection indicator will go off.
Hold the
(
+ paddle shifter for two seconds to return to normal drive.
■
When the transmission is in
(
S:
The vehicle will go into the sequential mode, and the M (sequential mode) indicator
and sequential mode gear selection indicator will come on.
If the vehicle speed increases and the engine speed reaches near the tachometer’s
red zone, the transmission automatically shifts up to the next gear.
You can cancel this mode by holding the
(
+ paddle shifter for two seconds. When
the sequential mode is canceled, the sequential mode indicator and sequential
mode gear selection indicator go off.
■
Sequential Mode
ELITE and TOURING grade models
* Not available on all models
553
uu
When Driving
u
Shifting
Driving
■
Sequential Mode Operation
1
Each paddle shift operation makes a single gear
change.
To change gears continuously, release the paddle
shifter before pulling it again for the next gear.
If the sequential mode gear selection indicator blinks
when you try to shift up or down, this means your
vehicle speed is not in its allowable gear range or the
protection of transmission system is necessary.
Slightly accelerate to shift up and decelerate to shift
down while the indicator is blinking.
Sequential
Mode Gear
Selection
Indicator
(
- Paddle Shifter
(Shift down)
(
+ Paddle Shifter
(Shift up)
Downshifting when
pulling the
(
- paddle
shifter.
(Changes to a lower
gear)
Upshifting when
pulling the
(
+ paddle
shifter.
(Changes to a higher
gear)
554
uu
When Driving
u
Auto Idle Stop
*
Driving
Auto Idle Stop
*
To help maximize fuel economy, the engine automatically stops when the vehicle
comes to a stop, depending on environmental and vehicle operating conditions. The
indicator (green) comes on at this time.
The engine then restarts once the vehicle is
about to move again, or depending on
environmental and vehicle conditions, and the
indicator (green) goes off.
2 The Engine Automatically Restarts When:
P. 557
A message associated with Auto Idle Stop
appears on the driver information interface.
2 Indicators P. 84
2 Customized Features P. 443
If the driver’s door is opened while the
indicator comes on, a buzzer sounds to notify
you that the Auto Idle Stop function is in
operation.
To turn the Auto Idle Stop system off, press
this button. The Auto Idle Stop system stops.
u
The Auto Idle Stop system will stop and
the indicator (amber) will come on.
The Auto Idle Stop system is turned on every
time you start the engine, even if you turned it
off the last time you drove the vehicle.
1
The 12-volt battery installed in this vehicle is
specifically designed for a model with Auto Idle Stop.
Using a 12-volt battery other than this specified type
may shorten the battery life, and prevent Auto Idle
Stop from activating. If you need to replace the
battery, make sure to select the specified type. Ask a
dealer for more details.
The duration of the Auto Idle Stop operation:
•
Increase in the ECON mode, compared to when
the ECON mode is off, with climate control in use.
Auto Idle Stop
Indicator (Green)
■
Auto Idle Stop System ON/OFF
1
Press the Auto Idle Stop OFF button to restart the
engine from the idling stop.
* Not available on all models
Continued
555
uu
When Driving
u
Auto Idle Stop
*
Driving
The vehicle stops with the gear position in
(
D and the brake pedal depressed.
■
Auto Idle Stop does not activate when:
• The Auto Idle Stop OFF button is pressed.
• The driver’s seat belt is not fastened.
• The engine coolant temperature is low or high.
• The transmission fluid temperature is low or high.
• The vehicle comes to a stop again before the vehicle speed reaches 3 mph (5 km/
h) after the engine starts.
• Stopped on a steep incline.
• The transmission is in a position other than
(
D.
• The engine is started with the hood open.
u
Turn off the engine. Close the hood before you restart the engine to activate
Auto Idle Stop.
• The battery charge is low.
• The internal temperature of the battery is 14°F (−10°C) or less.
• The climate control system is in use, and the outside temperature is below −4°F
(−20°C) or over 104°F (40°C).
• The climate control system is in use, and the temperature is set to Hi or Lo.
•
is on (indicator on).
• When the rear fan is set to maximum speed.
u
Auto Idle Stop may not activate under other conditions when the rear climate
control system is in use.
• When the Intelligent Traction Management is set to Snow.
■
Auto Idle Stop Activates When:
1
Auto Idle Stop Activates When:
Do not open the hood while the Auto Idle Stop
function is activated. If the hood is opened, the
engine will not restart automatically.
In this case, restart the engine with the ENGINE
START/STOP button.
2 Starting the Engine P. 538
Pressing the ENGINE START/STOP button changes
the power mode to ACCESSORY even while Auto Idle
Stop is in operation. Once in ACCESSORY, the engine
no longer restarts automatically. Follow the standard
procedure to start the engine.
2 Starting the Engine P. 538
556
uu
When Driving
u
Auto Idle Stop
*
Driving
■
Auto Idle Stop may not activate when:
• The vehicle is stopped by braking suddenly.
• The steering wheel is operated.
• The fan speed is high.
• Altitude is high.
• The vehicle is repeatedly accelerated and decelerated at a low speed.
• The climate control system is in use, and there is a significant difference between
the set temperature and the actual interior temperature.
• Humidity in the interior is high.
• The rear fan is set to maximum speed.
u
Auto Idle Stop may not activate under other conditions when the rear climate
control system is in use.
Continued
557
uu
When Driving
u
Auto Idle Stop
*
Driving
• The brake pedal is released (without the automatic brake hold system activated).
• The accelerator pedal is depressed (with the automatic brake hold system
activated).
■
The engine restarts even if the brake pedal is depressed
*1
when:
• The Auto Idle Stop OFF button is pressed.
• When a steering wheel is operated.
• The transmission is put into
(
R,
(
S, and
(
P, or taken out of
(
N and put into
(
D.
• The pressure on the brake pedal is reduced and the vehicle starts moving while
stopped on an incline.
• The pressure on the brake pedal is repeatedly applied and released slightly during
a stop.
• The battery charge becomes low.
• The accelerator pedal is depressed.
• The driver’s seat belt is unlatched.
•
is on (indicator on).
• The climate control system is in use, and the difference between the set
temperature and actual interior temperature becomes significant.
• The climate control system is being used to dehumidify the interior.
• The rear fan is set to maximum speed.
u
Auto Idle Stop may not activate under other conditions when the rear climate
control system is in use.
• When the Intelligent Traction Management is set to Snow.
■
The Engine Automatically Restarts When:
1
The Engine Automatically Restarts When:
If you are using an electronic device during Auto Idle
Stop, the device may temporarily be turned off when
the engine restarts.
1
The engine restarts even if the brake pedal is depressed
*1: With the automatic brake hold system activated,
you can release the brake pedal during Auto Idle Stop
is in operation.
558
uu
When Driving
u
Auto Idle Stop
*
Driving
■
The engine restarts even if the automatic brake hold system is activated
when:
• The automatic brake hold system is canceled and the electric parking brake is
applied automatically.
• The automatic brake hold system has a problem.
Briefly keeps the brake applied after releasing the brake pedal to restart the engine.
This can keep your vehicle from unexpectedly moving while on an incline.
■
Starting Assist Brake Function
559
uu
When Driving
u
ECON Button
Driving
ECON Button
The ECON button turns the ECON mode on
and off.
The ECON mode helps you improve your fuel
economy by adjusting the performance of the
engine, air conditioning system, and cruise
control.
1
While in ECON mode, the climate control system has
greater temperature fluctuations.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст