Honda Ridgeline (2022 year). Manual in english — page 7
109
uu
Indicators
u
Multi-Information Display Warning and Information Messages
In
strum
e
nt Pa
nel
Message
Condition
Explanation
●
Appears momentarily when the AC power outlet switch
is pressed and system is turned on.
●
Auto Idle Stop will not activate when the AC power
outlet is in use.
2
2
P. 191
Message
Condition
Explanation
●
Appears if there is a problem with the parking sensor
system.
●
Check if the area around the sensor(s) is covered with
mud, ice, snow, etc. If the indicator(s) stays on even
after you clean the area, have the system checked by a
dealer.
Message
Condition
Explanation
●
Appears when the washer fluid is low.
●
Refill the washer fluid.
2
P. 507
Models with AC Power Outlet
Models with parking sensor
Models with washer level sensor
* Not available on all models
110
In
strum
e
nt Pa
nel
Gauges and Multi-Information Display
Gauges
Gauges include the speedometer, fuel gauge, and other related indicators. They are
displayed when the power mode is in ON.
Displays your driving speed in mph or km/h.
Shows the number of engine revolutions per minute.
Displays the amount of fuel left in the fuel tank.
Displays the temperature of the engine coolant.
■
Speedometer
■
Tachometer
■
Fuel Gauge
■
Temperature Gauge
1
Press and hold the
RESET
button until you hear a
beep when the blank appears on the multi-
information display.
The speedometer reading as well as the displayed
measurements will switch between mph and km/h.
The display change message will switch for a few
seconds.
1
NOTICE
You should refuel when the needle approaches
.
Running out of fuel can cause the engine to misfire,
damaging the catalytic converter.
The actual amount of remaining fuel may differ from
the fuel gauge reading.
E
1
NOTICE
Driving with the temperature gauge needle in the
upper zone can cause serious engine damage. Pull
safely to the side of the road and allow engine
temperature to return to normal.
2
111
uu
Gauges and Multi-Information Display
u
Multi-Information Display
Continued
In
strum
e
nt Pa
nel
Multi-Information Display
The multi-information display shows the odometer, trip meter, outside temperature
indicator, and other gauges. It also displays important messages such as warnings
and other helpful information.
Press the
(information) or
RESET
button to change the display.
■
Switching the Display
Blank
Distance/
Average Fuel Economy/
Range/Instant Fuel
Economy
Trip A
Tire Pressure for Each Tire
Engine Oil Life
Turn-by-Turn
Directions
*
RESET
Button
Compass
*
Button
Distance/
Average Fuel Economy/
Range/Instant Fuel Economy
Trip B
Press the
Press and hold the
RESET
Changed two
seconds later
* Not available on all models
112
uu
Gauges and Multi-Information Display
u
Multi-Information Display
In
strum
e
nt Pa
nel
Shows the total number of miles or kilometers that your vehicle has accumulated.
■
Odometer
Odometer
Outside temperature
Continued
113
uu
Gauges and Multi-Information Display
u
Multi-Information Display
In
strum
e
nt Pa
nel
Shows the outside temperature in Fahrenheit (U.S.) or Celsius (Canada).
■
Adjusting the outside temperature display
Adjust the temperature reading by up to ±5°F or ±3°C if the temperature reading
seems incorrect.
Shows the total number of miles or kilometers driven since the last reset. Meters A
and B can be used to measure two separate trips.
■
Resetting a trip meter
To reset a trip meter, display it, then press and hold the
RESET
button until the trip
meter is reset to
0.0
.
Shows the estimated average fuel economy of each trip meter in mpg or l/100 km.
The display is updated at set intervals. When a trip meter is reset, the average fuel
economy is also reset.
■
Outside Temperature
■
Trip Meter
■
Average Fuel Economy
1
The temperature sensor is in the front bumper.
Road heat and exhaust from another vehicle can
affect the temperature reading when your vehicle
speed is less than 19 mph (30 km/h).
It may take several minutes for the display to be
updated after the temperature reading has stabilized.
You can adjust the temperature reading.
2
P. 298
1
Switch between trip meter A and trip meter B by
pressing the
button.
1
You can change when to reset the average fuel
economy.
2
P. 298
uu
Gauges and Multi-Information Display
u
Multi-Information Display
114
In
strum
e
nt Pa
nel
Shows the estimated distance you can travel on the remaining fuel. This estimated
distance is based on the vehicle’s current fuel economy.
Shows the instant fuel economy as a bar graph in mpg or l/100 km.
Shows each tire’s pressure.
2
Tire Pressure Monitoring System (TPMS) with Tire Fill Assist
P. 416
Shows the remaining oil life and Maintenance Minder
TM
.
2
P. 491
■
Compass
Shows the compass screen.
■
Turn-by-Turn Directions
When driving guidance is provided by the navigation system, turn-by-turn directions
to your destination appear.
2
Refer to the Navigation System Manual
■
Range
■
Instant Fuel Economy
■
Tire Pressure Monitor
■
Maintenance Minder
TM
■
Navigation
Models with navigation system
1
You can select whether to have the turn-by-turn
display come on or not during the route guidance.
2
P. 298
2
Refer to the navigation system
115
Controls
This chapter explains how to operate the various controls necessary for driving.
. . . . . . . . . . . . .. 116
Locking and Unlocking the Doors
Outside . . . . . . . . . . .. 120
Locking/Unlocking the Doors from the
Inside . . . . . . . . . . . . 127
Childproof Door Locks . . . . . . 129
Auto Door Locking/Unlocking . . .. 130
Immobilizer System . . . . . . .. 136
Security System Alarm. . . . . .. 136
Operating the Switches Around the
System) . . . . . . . . . . .. 154
Wipers and Washers . . . . . . 157
Rear Defogger/Heated Door Mirror
Button . . . . . . . . . . ... 159
Brightness Control . . . . . . ... 160
Driving Position Memory System
Adjusting the Steering Wheel . . .. 163
Interior Rearview Mirror . . . . ... 164
Power Door Mirrors . . . . . . . 165
. . . . . . . . . . . . .. 166
Interior/Exterior Convenience Items
* Not available on all models
116
Co
ntrols
Clock
Adjusting the Clock
You can adjust the time manually in the audio/information screen, with the power
mode in ON.
1.
Select
, then select
Settings
.
2.
Select
Clock/Info
, then
Clock
Adjustment
.
3.
Adjust the hours and minutes by selecting
/
.
4.
Select
OK
to set the time.
■
Adjusting the Time
1
The clock is automatically updated through the
navigation system, so the time does not need to be
adjusted.
You can customize the clock display to show the 12
hour clock or 24 hour clock.
2
P. 298
Models with navigation system
All models
3 4
117
Continued
Co
ntrols
Locking and Unlocking the Doors
Key
This vehicle comes with the following key:
Use the key to start and stop the engine, and
to lock or unlock all the doors or open the
trunk.
u
The tailgate lock/unlock function is set to
disable as the factory default setting. The
tailgate lock/unlock function can be used
by using the audio/information screen.
2
1
All the keys have an immobilizer system. The
immobilizer system helps to protect against vehicle
theft.
2
P. 136
Follow the advice below to prevent damage to the
keys:
•
Do not leave the keys in direct sunlight, or in
locations with high temperature or high humidity.
•
Do not drop the keys or set heavy objects on them.
•
Keep the keys away from liquids, dust and sand.
•
Do not take the keys apart except for replacing the
battery.
If the circuits in the keys are damaged, the engine
may not start, and the remote transmitter may not
work.
If the keys do not work properly, have them
inspected by a dealer.
You can remotely start the engine using the remote
engine start.
2
Keyless Remote
uu
Locking and Unlocking the Doors
u
Key
118
Co
ntrols
The built-in key can be used to lock/unlock the
doors or open the trunk when the keyless
remote battery becomes weak and the power
door lock/unlock operation is disabled.
To remove the built-in key, slide the release
knob and then pull out the key. To reinstall
the built-in key, push the built-in key into the
keyless remote until it clicks.
Contains a number that you will need if you
purchase a replacement key.
■
Built-in Key
Release Knob
Built-in Key
■
Key Number Tag
1
Keep the key number tag separate from the key in a
safe place outside of your vehicle.
If you wish to purchase an additional key, contact a
dealer. If you lose your key and you cannot start the
engine, contact a dealer.
119
uu
Locking and Unlocking the Doors
u
Low Keyless Remote Signal Strength
Co
ntrols
Low Keyless Remote Signal Strength
The vehicle transmits radio waves to locate the keyless remote when locking/
unlocking the doors, opening the trunk, or to start the engine.
In the following cases, locking/unlocking the doors, opening the trunk, or starting
the engine may be inhibited or operation may be unstable:
•
Strong radio waves are being transmitted by nearby equipment.
•
You are carrying the keyless remote together with telecommunications
equipment, laptop computers, cell phones, or wireless devices.
•
A metallic object is touching or covering the keyless remote.
1
Low Keyless Remote Signal Strength
Communication between the keyless remote and the
vehicle consumes the keyless remote’s battery.
Battery life is about two years, but this varies
depending on regularity of use.
The battery is consumed whenever the keyless
remote is receiving strong radio waves. Avoid placing
it near electrical appliances such as televisions and
personal computers.
120
uu
Locking and Unlocking the Doors
u
Locking/Unlocking the Doors from the Outside
Co
ntrols
Locking/Unlocking the Doors from the Outside
When you carry the keyless remote, you can
lock/unlock the doors and open the trunk.
You can lock/unlock the doors within a radius
of about 32 inches (80 cm) of the outside door
handle. You can open the trunk within about
32 inches (80 cm) radius from the trunk
release button.
■
Using the Keyless Access System
1
Locking/Unlocking the Doors from the Outside
If the interior light switch is in the door activated
position, the interior light comes on when you unlock
the doors.
No doors opened: The light fades out after
30 seconds.
Doors relocked: The light goes off immediately.
2
P. 175
1
Using the Keyless Access System
If you do not open a door within 30 seconds of
unlocking the vehicle with the keyless access system,
the doors will automatically relock.
You can lock or unlock doors using the keyless access
system only when the power mode is in VEHICLE OFF.
Continued
121
uu
Locking and Unlocking the Doors
u
Locking/Unlocking the Doors from the Outside
Co
ntrols
■
Locking the doors
Press the door lock button on the front door.
u
Some exterior lights flash; the beeper
sounds; all the doors lock; and the
security system sets.
1
Using the Keyless Access System
•
Do not leave the keyless remote in the vehicle
when you get out. Carry it with you.
•
Even if you are not carrying the keyless remote, you
can lock/unlock the doors or open the trunk while
someone else with the remote is within range.
•
The door may be unlocked if the door handle is
covered with water in heavy rain or in a car wash if
the keyless remote is within range.
•
If you grip a door handle wearing gloves, the door
sensor may be slow to respond or may not respond
by unlocking the doors.
•
After locking the door, you have up to two seconds
during which you can pull the door handle to
confirm whether the door is locked.
If you need to unlock the door immediately after
locking it, wait at least two seconds before
gripping the handle, otherwise the door will not
unlock.
•
The door might not open if you pull it immediately
after gripping the door handle. Grip the handle
again and confirm that the door is unlocked before
pulling the handle.
•
Even within the 32 inches (80 cm) radius, you may
not be able to lock/unlock the doors with the
keyless remote if it is above or below the outside
handle.
•
The keyless remote may not operate if it is too close
to the door and door glass.
Door Lock Button
uu
Locking and Unlocking the Doors
u
Locking/Unlocking the Doors from the Outside
122
Co
ntrols
■
Unlocking the doors and trunk
Grab the driver’s door handle:
u
The driver’s door unlocks.
u
Some exterior lights flash twice and the
beeper sounds twice.
Grab the front passenger’s door handle:
u
All doors unlock.
u
Some exterior lights flash twice and the
beeper sounds twice.
Press the trunk release button:
u
The trunk unlocks and opens.
u
The beeper sounds once.
2
Using the Trunk Release Button
1
Using the Keyless Access System
The light flash, beep and door unlock mode settings
can be customized using the audio/information
screen.
2
P. 298
Trunk Release Button
Continued
123
uu
Locking and Unlocking the Doors
u
Locking/Unlocking the Doors from the Outside
Co
ntrols
■
Locking the doors (Walk away auto
lock
®
)
When you walk away from the vehicle with all
doors closed while carrying the keyless
remote, the doors will automatically lock.
The auto lock function activates when all
doors are closed, and the keyless remote is
within about 5 feet (1.5 m) radius of the
outside door handle.
Exit vehicle while carrying keyless remote and
close door(s).
1.
While within about 5 feet (1.5 m) radius of
the vehicle.
u
The beeper sounds; the auto lock
function will be activated.
2.
Carry the keyless remote beyond about 5
feet (1.5 m) from the vehicle and remain
outside this range for 2 or more seconds.
u
Some exterior lights flash; the beeper
sounds; all doors will then lock.
1
Locking the doors (Walk away auto lock
The auto lock function is set to OFF as the factory
default setting. The auto lock function can be set to
ON using the audio/information screen.
If you set the auto lock function to ON using the
audio/information screen only the keyless remote
that was used to unlock the driver’s door prior to the
setting change can activate auto lock.
2
P. 298
After the auto lock function has been activated,
when you stay within the locking/unlocking
operation range, the indicator on the keyless remote
will continue to flash until the doors are locked.
When you stay beside the vehicle within the
operation range, the doors will automatically lock
approximately 30 seconds after the auto lock
function activating beeper sounds.
When you open a door after the auto lock function
activating beeper sounds, the auto lock function will
be canceled.
Under the following circumstances, the auto-lock
function will not activate:
•
The keyless remote is inside the vehicle.
u
The beeper will not sound.
•
The keyless remote is taken out of its operational
range before all the doors are closed.
u
The beeper will sound.
The activation range of
the auto lock function is
about 5 feet (1.5 m)
a
b
uu
Locking and Unlocking the Doors
u
Locking/Unlocking the Doors from the Outside
124
Co
ntrols
To temporarily deactivate the function:
1.
Set the power mode to VEHICLE OFF.
2.
Open the driver’s door.
3.
Using the master door lock switch, operate
the lock as follows:
Lock
Unlock
Lock
Unlock.
u
The beeper sounds and the function is
deactivated.
To restore the function:
•
Set the power mode to ON.
•
Lock the vehicle without using the auto lock
function
•
With the keyless remote on you, move out
of the auto lock function operation range.
•
Open any door.
1
Locking the doors (Walk away auto lock
The auto lock function does not operate when any of
the following conditions are met.
•
The keyless remote is inside the vehicle.
•
A door or the hood is not closed.
•
The power mode is set to any mode other than
OFF.
•
The keyless remote is not located within a radius of
about 5 feet (1.5 m) from the vehicle when you get
out of the vehicle and close the doors.
Auto lock function operation stop beeper
After the auto lock function has been activated, the
auto lock operation stop beeper sounds for
approximately two seconds in the following cases.
•
The keyless remote is put inside the vehicle through
a window.
•
You are located too close to the vehicle.
•
The keyless remote is put inside the trunk.
If the warning beeper sounds, check that you are
carrying the keyless remote. Then, open/close a door
and confirm the auto lock activation beeper sounds
once.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст