Honda Crosstour (2015 year). Instruction — part 31
480
uu
Maintenance Under the Hood
u
Transmission Fluid
Main
tenan
ce
Transmission Fluid
Have a dealer check the fluid level and replace if necessary.
■
Automatic Transmission Fluid
Specified fluid: Honda Automatic Transmission Fluid ATF DW-1
1
NOTICE
Do not mix Honda ATF DW-1 with other
transmission fluids.
Using a transmission fluid other than Honda ATF
DW-1 may adversely affect the operation and
durability of your vehicle’s transmission, and damage
the transmission.
Any damage caused by using a transmission fluid that
is not equivalent to Honda ATF DW-1 is not covered
by Honda’s new vehicle warranty.
481
uu
Maintenance Under the Hood
u
Brake Fluid
Main
tenan
ce
Brake Fluid
The fluid level should be between the MIN
and MAX marks on the side of the reservoir.
Specified fluid: Honda Heavy Duty Brake Fluid DOT 3
■
Checking the Brake Fluid
1
NOTICE
Brake fluid marked DOT 5 is not compatible with your
vehicle’s braking system and can cause extensive
damage.
If the specified brake fluid is not available, you should
use only DOT 3 or DOT 4 fluid from a sealed
container as a temporary replacement.
Using any non-Honda brake fluid can cause corrosion
and decrease the longevity of the system. Have the
brake system flushed and refilled with Honda Heavy
Duty Brake Fluid DOT 3 as soon as possible.
If the brake fluid level is at or below the MIN mark,
have a dealer inspect for leaks or worn brake pads as
soon as possible.
Brake Reservoir
MIN
MAX
482
uu
Maintenance Under the Hood
u
Power Steering Fluid Check
*
Main
tenan
ce
Power Steering Fluid Check
*
We recommend that you check the power steering fluid level every time you refuel.
Check when the engine is not running.
1. Look at the side of the reservoir. The fluid
should be between the UPPER LEVEL and
LOWER LEVEL.
2. Add power steering fluid if necessary to the
UPPER LEVEL mark.
u
Inspect the system for a leak. If the fluid
level goes below the LOWER LEVEL
frequently, have the system inspected as
soon as possible.
Specified fluid: Honda Power Steering Fluid
1
NOTICE
Turning the steering wheel to full left or right lock
and holding it there can damage the power steering
pump.
NOTICE
Pour the fluid slowly and carefully so you do not spill
any. Clean up any spills immediately; it could damage
components in the engine compartment.
4-cylinder models
LOWER
LEVEL
UPPER
LEVEL
* Not available on all models
483
uu
Maintenance Under the Hood
u
Refilling Window Washer Fluid
Main
tenan
ce
Refilling Window Washer Fluid
Check the amount of window washer fluid using the washer fluid level gauge on the
cap.
If the level is low, fill the washer reservoir.
If the washer fluid is low, the washer level
indicator comes on.
Pour the washer fluid carefully. Do not overflow the reservoir.
1
NOTICE
Do not use engine antifreeze or a vinegar/water
solution in the windshield washer reservoir.
Antifreeze can damage your vehicle’s paint. A
vinegar/water solution can damage the windshield
washer pump.
Level Gauge
Canadian models
484
Main
tenan
ce
Replacing Light Bulbs
Headlight Bulbs
When replacing, use the following bulbs.
1. Remove the engine coolant reserve tank.
2. Push the tab to remove the coupler.
3. Rotate the old bulb to the left to remove.
4. Insert a new bulb into the headlight
assembly and turn it to the right.
5. Insert the coupler into the connector of the
bulb.
High beam headlight: 60W (HB3 for halogen bulb type)
Low beam headlight: 55W (H11 for halogen bulb type)
■
High Beam Headlight
1
NOTICE
Halogen bulbs get very hot when lit.
Oil, perspiration, or a scratch on the glass can cause
the bulb to overheat and shatter.
The headlight aim is set by the factory, and does not
need to be adjusted. However, if you regularly carry
heavy items in the cargo area or tow a trailer, have
the aiming readjusted at a dealer or by a qualified
technician.
When replacing a halogen bulb, handle it by its base,
and protect the glass from contact with your skin or
hard objects. If you touch the glass, clean it with
denatured alcohol and a clean cloth.
Passenger side
Tab
Coupler
Bulb
485
uu
Replacing Light Bulbs
u
Headlight Bulbs
Main
tenan
ce
1. Turn the steering wheel all the way to the
opposite side from the light being replaced.
Passenger side: Turn the steering wheel
to the left.
Driver side: Turn the steering wheel to the
right.
2. Remove the holding clip and screw, and
pull the inner fender back.
3. Push the tab to remove the coupler.
4. Rotate the old bulb to the left to remove.
5. Insert a new bulb into the headlight
assembly and turn it to the right.
6. Insert the coupler into the connector of the
bulb.
■
Low Beam Headlights
1
Insert a flat-tip screwdriver, lift and remove the
central pin to remove the clip.
Insert the clip with the central pin raised, and push
until it is flat.
Central pin
Push until the
pin is flat.
Holding
Clip
Screw
Tab
Coupler
Bulb
486
uu
Replacing Light Bulbs
u
Fog Light Bulbs
Main
tenan
ce
Fog Light Bulbs
When replacing, use the following bulbs.
1. Remove the holding clips, then push up the
under cover.
2. Push the tab to remove the coupler.
3. Rotate the old bulb to the left to remove.
4. Insert a new bulb into the fog light
assembly and turn it to the right.
5. Insert the coupler into the connector of the
bulb.
Fog Light: 55 W (H11 for halogen bulb type)
1
NOTICE
Halogen bulbs get very hot when lit. Oil, perspiration,
or a scratch on the glass can cause the bulb to
overheat and shatter.
When replacing a halogen bulb, handle it by its
plastic case, and protect the glass from contact with
your skin or hard objects. If you touch the glass, clean
it with denatured alcohol and a clean cloth.
Remove the clip by using a flat-tip screwdriver.
Holding Clips
Under Cover
Passenger side
Tab
Coupler
Bulb
487
uu
Replacing Light Bulbs
u
Fog Light Bulbs
Main
tenan
ce
1. Turn the steering wheel all the way to the
right.
2. Remove the holding clips and screw, and
pull the inner fender back.
3. Push the tab to remove the coupler.
4. Rotate the old bulb to the left to remove.
5. Insert a new bulb into the headlight
assembly and turn it to the right.
6. Insert the coupler into the connector of the
bulb.
1
Remove the clip by using a flat-tip screwdriver.
2 Low Beam Headlights P. 485
Holding Clip
Screw
Driver side
Bulb
Coupler
Tab
488
uu
Replacing Light Bulbs
u
Front Side Marker Light Bulb
Main
tenan
ce
Front Side Marker Light Bulb
When replacing, use the following bulbs.
1. Turn the steering wheel all the way to the
opposite side from the light being replaced.
Passenger side: Turn the steering wheel
to the left.
Driver side: Turn the steering wheel to the
right.
2. Remove the holding clips and screw, and
pull the inner fender back.
3. Turn the socket to the left and remove it,
then remove the old bulb.
4. Insert a new bulb.
Front Side Marker Light: 5 W
1
Remove the clip by using a flat-tip screwdriver.
Holding Clip
Screw
Bulb
Socket
489
uu
Replacing Light Bulbs
u
Front Turn Signal/Parking Light Bulbs
Continued
Main
tenan
ce
Front Turn Signal/Parking Light Bulbs
When replacing, use the following bulbs.
1. Unlock the holding clips, then remove the
upper part of the air intake duct and the air
intake tube.
1. Remove the engine coolant reserve tank.
Front Turn Signal/Parking: 24/2.2CP
Tube
Holding Clip
Holding Clip
Driver side
6-cylinder models
Passenger side
All models
490
uu
Replacing Light Bulbs
u
Brake/Taillights, Back-Up Light, Rear Turn Signal Light and Rear Side Marker Light Bulbs
Main
tenan
ce
2. Turn the socket to the left and remove it.
3. Push in the old bulb, rotate to the left until
it unlocks, and remove.
4. Insert new bulb.
Brake/Taillights, Back-Up Light, Rear Turn Signal
Light and Rear Side Marker Light Bulbs
When replacing, use the following bulbs.
1. Pry on the edge of the cover using a flat-tip
screwdriver to remove the covers.
u
Wrap the flat-tip screwdriver with a cloth
to prevent scratches.
Bulb
Socket
Brake/Taillight: 21/5 W
Back-Up Light: 21 W
Rear Turn Signal Light: 21 W (Amber)
Rear Side Maker Light: 3 CP
Cover
491
uu
Replacing Light Bulbs
u
Brake/Taillights, Back-Up Light, Rear Turn Signal Light and Rear Side Marker Light Bulbs
Main
tenan
ce
2. Use a Phillip-head screwdriver to remove
the bolts.
3. Pull the light assembly out of the rear pillar.
4. Turn the socket to the left and remove it.
Remove the old bulb.
5. Insert a new bulb.
Bolt
Bulb
Socket
492
uu
Replacing Light Bulbs
u
Rear License Plate Light Bulb
Main
tenan
ce
Rear License Plate Light Bulb
When replacing, use the following bulb.
1. Push the left edge of the lens to the right
and pull out the licence light assembly.
2. Push the tabs to remove the lens.
3. Remove the old bulb.
4. Insert a new bulb.
High-Mount Brake Light Bulb
High-mount brake light bulbs are LED type. Have an authorized Honda dealer
inspect and replace the light bulbs.
Rear License Plate Light: 5 W
Bulb
Tab
Tab
Lens
493
Continued
Main
tenan
ce
Checking and Maintaining Wiper Blades
Checking Wiper Blades
If the wiper blade rubber has deteriorated, it will leave streaks and the hard surfaces
of the blade may scratch the window glass.
Changing the Front Wiper Blade Rubber
1. Lift the driver side wiper arm first, then the
passenger side.
2. Pry on the edge of the lock tab using a flat-
tip screwdriver to push it up.
u
Wrap the flat-tip screwdriver with a cloth
to prevent scratches.
3. Slide the blade from the wiper arm.
1
Changing the Front Wiper Blade Rubber
NOTICE
Avoid dropping the wiper arm; it may damage the
windshield.
Lock Tab
494
uu
Checking and Maintaining Wiper Blades
u
Changing the Front Wiper Blade Rubber
Main
tenan
ce
4. Slide the wiper blade out from its holder by
pulling the tabbed end out.
5. Remove the retainers from the rubber blade
that has been removed, and mount to a
new rubber blade.
u
Correctly align the rubber protrusion and
the retainer grooves.
6. Slide the new wiper blade onto the holder
from the bottom end.
u
The tab on the holder should fit in the
indent of the wiper blade.
7. Slide the wiper blade onto the wiper arm,
then push down the lock tab.
8. Lower the passenger side wiper arm first,
then the driver side.
Blade
Top
Retainer
Blade
Tab
Indent
495
uu
Checking and Maintaining Wiper Blades
u
Changing the Rear Wiper Blade Rubber
Continued
Main
tenan
ce
Changing the Rear Wiper Blade Rubber
1. Raise the wiper arm off.
2. Pry on the edge of the lock tab using a flat-
tip screwdriver to push it up.
u
Wrap the flat-tip screwdriver with a cloth
to prevent scratches.
3. Slide the wiper blade out from the end with
the indent.
1
Changing the Rear Wiper Blade Rubber
NOTICE
Avoid dropping the wiper arm; it may damage the
rear window.
Lock Tab
Blade
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст