Honda Ridgeline (2023 year). Manual in english — page 25
uu
When Driving
u
Shifting
398
Driving
In freezing or sub-freezing conditions, the shift selection response may be slow.
Always depress the brake pedal before putting the transmission into
(
P
, and
confirm that
(
P
is shown on the shift position indicator before releasing the brake.
■
When opening the driver’s door
If you open the driver’s door under the following conditions, the transmission
automatically changes to
(
P
.
•
The vehicle is stationary with the engine running, or moving at 1 mph (2 km/h) or
slower.
•
The transmission is in other than
(
P
.
•
You have unfastened the driver side seat belt.
u
If you manually put the transmission into any other position from
(
P
with the
brake pedal depressed, the transmission will automatically return to
(
P
once
you release the brake pedal.
■
When turning off the power mode
If you turn the engine off while the vehicle is stationary, and the transmission is in
other than
(
P
, the transmission automatically changes to
(
P
.
1
The beeper sounds once when you change to
(
R
.
2
P. 299
1
When opening the driver’s door
While the system is designed to automatically change
the transmission to
(
P
under the described
conditions, in the interest of safety you should always
select
(
P
before opening the driver’s door.
Make sure to park the vehicle in a safe place.
2
P. 472
If you want to drive the vehicle after the transmission
has automatically changed to
(
P
under the described
conditions, close the door, fasten the seat belt,
depress the brake pedal, then change the shift
position.
If you leave the vehicle, turn off the engine and lock
the doors.
Continued
399
uu
When Driving
u
Shifting
Driving
■
If you want to keep the transmission in
(
N
position [car wash mode]
With the engine running:
1.
Press and hold the brake pedal.
2.
Select
(
N
, then release the button to display (Neutral)
(
N
hold mode on the
multi-information display.
3.
Press and hold
(
N
again for two seconds.
u
This puts the vehicle in car wash mode which must be used when your vehicle
is pulled through a conveyor type automatic car wash where you or an
attendant do not remain in the vehicle.
If the
ENGINE STOP/START
button is pressed
after car wash mode has been activated, the
power mode will change to ACCESSORY and a
message will be displayed on the multi-
information display.
u
For 15 minutes the transmission remains
in
(
N
with the power mode in
ACCESSORY. After that, the
transmission automatically changes to
(
P
and the power mode changes to OFF.
u
Manually changing to
(
P
cancels
ACCESSORY mode. The
(
P
indicator
comes on and the power mode changes
to OFF. You must always put the
transmission into
(
P
when car wash
mode is no longer needed.
1
If you want to keep the transmission in
(
N
position [car wash mode]
Note that the transmission may not stay in
(
N
position while any of the following indicators is on:
•
Transmission system indicator.
•
Malfunction indicator lamp.
•
Charging system indicator.
400
uu
When Driving
u
Shifting
Driving
■
Restrictions on selecting a shift position
You cannot select a shift position under certain circumstances that may lead to a crash.
When the
transmission is in:
1. Under these circumstances
2. If you try to change to the
following:
3. The shift position
remains in/changes to:
How to change the
shift position
(
P
The brake pedal is not
depressed.
Other shift position
(
P
Release the accelerator
pedal and depress the
brake pedal.
The accelerator pedal is
depressed.
(
N
The vehicle is moving at low
speed without the brake pedal
depressed.
(
N
The vehicle is moving at low
speed with the accelerator
pedal depressed.
(
N
,
(
D
or
(
S
The vehicle is moving forward.
(
R
Stop your vehicle in a
safe place, keep the
brake pedal pressed,
and select the
appropriate shift
position.
(
R
or
(
N
The vehicle is moving backward.
(
D
,
(
S
(
R
,
(
N
,
(
D
or
(
S
The vehicle is moving.
(
P
401
uu
When Driving
u
Shifting
Continued
Driving
Use the paddle shifters to change between 1st and 9th gears without removing your
hands from the steering wheel. The transmission will switch to the sequential mode.
■
When the transmission is in
(
D
:
The vehicle will go into the sequential mode momentarily, and the sequential mode
gear selection indicator will come on.
Once you start traveling at a constant speed, the sequential mode will automatically
switch off, and the sequential mode gear selection indicator will go off.
Hold the
(
+
paddle shifter for two seconds or push
button to return to normal
drive.
■
When the transmission is in
(
S
:
The vehicle will go into the sequential mode, and the
M
(sequential mode) indicator
and sequential mode gear selection indicator will come on.
If the vehicle speed increases and the engine speed reaches near the tachometer’s
red zone, the transmission automatically shifts up to the next gear.
You can cancel this mode by holding the
(
+
paddle shifter for two seconds or push
button. When the sequential mode is canceled, the
M
(sequential mode)
indicator and sequential mode gear selection indicator go off.
■
Sequential Mode
D/S
D/S
uu
When Driving
u
Shifting
402
Driving
■
Sequential Mode Operation
1
Each paddle shift operation makes a single gear
change.
To change gears continuously, release the paddle
shifter before pulling it again for the next gear.
If the sequential mode gear selection indicator blinks
when you try to shift up or down, this means your
vehicle speed is not in its allowable gear range or the
protection of transmission system is necessary.
Slightly accelerate to shift up and decelerate to shift
down while the indicator is blinking.
Sequential
Mode Gear
Selection
Indicator
Downshifting when pulling
the
paddle shifter.
(Changes to a lower gear)
Upshifting when pulling
the
paddle shifter.
(Changes to a higher gear)
Paddle Shifter
(Shift down)
Paddle Shifter
(Shift up)
403
uu
When Driving
u
ECON Mode
Driving
ECON Mode
The
ECON
button turns the ECON mode on
and off.
The ECON mode helps you improve your fuel
economy by adjusting the performance of the
engine and climate control system.
1
While in ECON mode, the climate control system has
greater temperature fluctuation.
If the
Snow
,
Mud
*
or
Sand
*
mode is turned ON
while the ECON mode is ON, the ECON mode will be
turned off.
* Not available on all models
404
uu
When Driving
u
Intelligent Traction Management
Driving
Intelligent Traction Management
The Intelligent Traction Management optimizes vehicle performance to help you
drive on various surfaces. The system has available modes to select from:
Normal
,
Snow
,
Mud
*
, and
Sand
*
.
Press the mode button to select the appropriate mode. The mode you select appears
on the multi-information display. When the vehicle is turned off and restarted,
Intelligent Traction Management mode will revert to Normal.
1
Intelligent Traction Management
Refer to the Off-Highway Driving section for driving
tips and safety precautions.
2
Off-Highway Driving Guidelines
Mud
Use when driving on
muddy road or off-
road surfaces.
Sand
Use when driving on
soft, sandy road or
off-road surfaces.
Normal
Provides balanced
driving performance
on most road surfaces.
Mode Button
Snow
Use when driving on
snowy road surfaces.
AWD models
* Not available on all models
405
uu
When Driving
u
Intelligent Traction Management
Driving
Normal
Provides balanced
driving performance
on most road surfaces.
SNOW
Button
Snow
Use when driving on
snowy road surfaces.
2WD models
406
uu
When Driving
u
Auto Idle Stop
Driving
Auto Idle Stop
To help maximize fuel economy, the engine automatically stops when the vehicle
comes to a stop, depending on environmental and vehicle operating conditions. The
indicator (green) comes on at this time.
The environmental and vehicle conditions that
impact Auto Idle Stop system operation are
varied.
2
Auto Idle Stop Activates When:
P. 408,
The engine then restarts once the vehicle is
about to move again, and the indicator
(green) goes off.
2
The Engine Automatically Restarts When:
P. 410
If the driver’s door is opened while the
indicator (green) comes on, a buzzer sounds
to notify you that the Auto Idle Stop function
is in operation.
A message associated with Auto Idle Stop
appears on the multi-information display.
2
P. 78
2
P. 299
1
The 12-volt battery installed in this vehicle is
specifically designed for a model with Auto Idle Stop.
Using a 12-volt battery other than this specified type
may shorten the 12-volt battery life, and prevent
Auto Idle Stop from activating. If you need to replace
the 12-volt battery, make sure to select the specified
type. Ask a dealer for more details.
The duration of the Auto Idle Stop operation:
•
Increase in the ECON mode, compared to when the
ECON mode is off, with climate control in use.
2
Auto Idle Stop
Indicator (Green)
Continued
407
uu
When Driving
u
Auto Idle Stop
Driving
To turn the Auto Idle Stop system off, press
this button. The Auto Idle Stop system stops.
u
Auto Idle Stop system will stop and the
indicator (Amber) will come on.
The Auto Idle Stop system is turned on every
time you start the engine, even if you turned it
off the last time you drove the vehicle.
■
Auto Idle Stop System ON/OFF
1
If you turn off the Auto Idle Stop system while it is
activated, the engine will restart.
Auto Idle Stop
System Indicator
(Amber)
uu
When Driving
u
Auto Idle Stop
408
Driving
The vehicle stops with the transmission in
(
D
and the brake pedal depressed.
When you put the transmission into
(
P
, the Auto Idle Stop continues to operate,
even if the brake pedal is released.
u
If you depress the brake pedal, the engine may automatically restart.
■
Auto Idle Stop does not activate when:
•
The Auto Idle Stop
OFF
button is pressed.
•
The driver’s seat belt is not fastened.
•
The engine is not adequately warmed up or coolant temperature is high.
•
The transmission fluid temperature is low or high.
•
The vehicle comes to a stop again before the vehicle speed reaches 3 mph (5
km/h) after the engine starts.
•
The vehicle is stopped on a steep incline.
•
The transmission is in a position other than
(
D
.
•
The engine is started with the hood open.
u
Turn off the engine. Close the hood before you restart the engine to activate
Auto Idle Stop.
•
The battery charge is low.
•
The internal temperature of the battery is 14°F (−10°C) or less.
•
The climate control system is in use, and the outside temperature is below −4°F
(−20°C) or over 104°F (40°C).
•
The climate control system is in use, and the temperature is set to
Hi
or
Lo
.
•
is ON (indicator on).
•
The Intelligent Traction Management is set to Snow, Mud
*
, or Sand
*
.
•
The AC power outlet is used.
■
Auto Idle Stop Activates When:
1
Auto Idle Stop Activates When:
Do not open the hood while the Auto Idle Stop
function is activated. If the hood is opened, the
engine will not restart automatically.
In this case, restart the engine with the
ENGINE
START/STOP
button.
2
P. 385
Pressing the
ENGINE START/STOP
button causes
the engine to no longer restart automatically.
Follow the standard procedure to start the engine.
2
P. 385
Models with AC Power Outlet
* Not available on all models
409
uu
When Driving
u
Auto Idle Stop
Continued
Driving
■
Auto Idle Stop may not activate when:
•
The vehicle is stopped by braking suddenly.
•
The steering wheel is operated.
•
The fan speed is high.
•
Altitude is high.
•
The climate control system is in use, and there is a significant difference between
the set temperature and the actual interior temperature.
•
The climate control system is in use, and humidity in the interior is high.
uu
When Driving
u
Auto Idle Stop
410
Driving
The brake pedal is released.
■
The engine restarts even if the brake pedal is depressed when:
•
The Auto Idle Stop
OFF
button is pressed.
•
The steering wheel is operated.
•
The transmission is put into
(
R
or
(
S
, or when it is set from
(
N
to
(
D
.
u
If you put the transmission into
(
P
after the Auto Idle Stop activates, the Auto
Idle Stop continues to operate. In this case, the engine restarts when you
depress the brake pedal.
•
The pressure on the brake pedal is reduced and the vehicle starts moving while
stopped on an incline.
•
The pressure on the brake pedal is repeatedly applied and released slightly during
a stop.
•
The battery charge becomes low.
•
The accelerator pedal is depressed.
•
The driver’s seat belt is unlatched.
•
is ON (indicator on).
•
The climate control system is in use, and the difference between the set
temperature and actual interior temperature becomes significant.
•
The climate control system is being used to dehumidify the interior.
•
The Intelligent Traction Management is set to Snow, Mud
*
, or Sand
*
.
•
The AC power outlet is used.
■
The Engine Automatically Restarts When:
1
The Engine Automatically Restarts When:
If you are using an electronic device during Auto Idle
Stop, the device may temporarily be turned off when
the engine restarts.
Models with AC Power Outlet
* Not available on all models
412
uu
When Driving
u
Vehicle Stability Assist
TM
(VSA
®
), aka Electronic Stability Control (ESC), System
Driving
Vehicle Stability Assist
TM
(VSA
®
), aka Electronic
Stability Control (ESC), System
VSA
®
helps to stabilize the vehicle during cornering if the vehicle turns more or less
than what was intended. It also assists in maintaining traction on slippery surfaces.
It does so by regulating engine output and selectively applying the brakes.
When VSA
®
activates, you may notice that the
engine does not respond to the accelerator.
You may also notice some noise from the
hydraulic brake system. You will also see the
indicator blink.
■
VSA
®
Operation
1
), aka Electronic Stability Control
The VSA
®
may not function properly if tire type and
size are mixed. Make sure to use the same size and
type of tire, and the air pressures as specified.
When the VSA
®
system indicator comes on and stays
on while driving, there may be a problem with the
system. While this may not interfere with normal
driving, have your vehicle checked by a dealer
immediately.
VSA
®
cannot enhance stability in all driving situations
and does not control the entire braking system. You
still need to drive and corner at speeds appropriate
for the conditions and always leave a sufficient
margin of safety.
The main function of the VSA
®
system is generally
known as Electronic Stability Control (ESC). The
system also includes a traction control function.
VSA
®
System
Indicator
413
uu
When Driving
u
Vehicle Stability Assist
TM
(VSA
®
), aka Electronic Stability Control (ESC), System
Driving
This button is on the driver side control panel.
To partially disable VSA
®
functionality/
features, press and hold it until you hear a
beep.
The traction control stops fully functioning,
allowing the wheels to spin more freely at low
speed. The VSA
®
OFF
indicator will also come
on and a message on the multi-information
display informs you that the mode is changed.
Traction control mode cannot be changed
during Mud or Sand modes. If you are driving
on mud or sand, Mud or Sand Intelligent
Traction Management modes can also be
used to free a stuck vehicle. On other road
surfaces, change to Normal or Snow mode,
then press and hold the
(VSA
®
OFF
)
button.
To restore VSA
®
functionality/features, press
the
(VSA
®
OFF
) button until you hear a
beep.
VSA
®
is turned on every time you start the
engine, even if you turned it off the last time
you drove the vehicle.
■
VSA
®
On and Off
1
), aka Electronic Stability Control
In certain unusual conditions when your vehicle gets
stuck in shallow mud or fresh snow, it may be easier
to free it with the VSA
®
temporarily switched off.
When the
button is pressed, the traction control
function becomes less effective. This allows for the
wheels to spin more freely at low speed. You should
only attempt to free your vehicle with the VSA
®
off if
you are not able to free it when the VSA
®
is on.
Immediately after freeing your vehicle, be sure to
switch VSA
®
on again. We do not recommend driving
your vehicle with the VSA
®
system switched off.
You may hear a motor sound coming from the
engine compartment while system checks are being
performed immediately after starting the engine or
while driving. This is normal.
VSA
®
OFF
Indicator
When the
button is pressed
AWD models
414
uu
When Driving
u
Agile Handling Assist
Driving
Agile Handling Assist
Lightly brakes each of the front and rear wheels, as needed, when you turn the
steering wheel, and helps support the vehicle’s stability and performance during
cornering.
1
The agile handling assist cannot enhance stability in
all driving situations. You still need to drive and
corner at speeds appropriate for the conditions and
always leave a sufficient margin of safety.
When the VSA
®
system indicator comes on and stays
on while driving, the agile handling assist does not
activate.
You may hear a sound coming from the engine
compartment while the agile handling assist is
activated. This is normal.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст