Honda Ridgeline (2023 year). Manual in english — page 29
463
uu
Honda Sensing
®
u
Road Departure Mitigation System
Continued
Driving
The system may not properly detect lane markings and the position of your vehicle
under certain conditions. Some examples of these conditions are listed below.
■
Environmental conditions
•
Driving in bad weather (rain, fog, snow, etc.).
•
Sudden changes between light and dark, such as an entrance or exit of a tunnel.
•
There is little contrast between lane lines and the roadway surface.
•
Driving into low sunlight (e.g., at dawn or dusk).
•
Strong light is reflected onto the roadway.
•
Driving in the shadows of trees, buildings, etc.
•
Shadows of adjacent objects are parallel to lane markings.
•
Roadway objects or structures are misinterpreted as lane markers.
•
Reflections on the interior of the windshield.
•
Driving at night or in a dark condition such as a tunnel.
■
Road Departure Mitigation system Conditions and
Limitations
464
uu
Honda Sensing
®
u
Road Departure Mitigation System
Driving
■
Roadway conditions
•
Driving on a snowy or wet roadway (obscured lane marking, vehicle tracks,
reflected lights, road spray, high contrast).
•
Driving on a road with temporary lane markings.
•
Faint, multiple, or varied lane markings are visible on the roadway due to road
repairs or old lane markings.
•
The roadway has merging, split, or crossing lines (e.g., such as at an intersection
or crosswalk).
•
The lane markings are extremely narrow, wide, or changing.
•
The vehicle in front of you is driving near the lane lines.
•
The road is hilly or the vehicle is approaching the crest of a hill.
•
Driving on rough or unpaved roads, or over bumpy surfaces.
•
When objects on the road (curb, guard rail, pylons, etc.) are recognized as white
(or yellow) lines.
•
Driving on roads with double lines.
■
Vehicle conditions
•
Headlight lenses are dirty or the headlights are not properly adjusted.
•
The outside of the windshield is streaked or blocked by dirt, mud, leaves, wet
snow, etc.
•
The inside of the windshield is fogged.
•
The camera temperature gets too high.
•
An abnormal tire or wheel condition (incorrect sizes, varied sizes or construction,
improperly inflated, compact spare tire, etc.).
•
The vehicle is tilted due to a heavy load or suspension modifications.
•
When tire chains are installed.
•
The vehicle is towing a trailer.
465
uu
Honda Sensing
®
u
Front Sensor Camera
Continued
Driving
Front Sensor Camera
The camera, used in systems such as LKAS, Road Departure Mitigation system, ACC,
and CMBS
TM
, is designed to detect an object that triggers any of the systems to
operate their functions.
This camera is located behind the rearview
mirror.
To help reduce the likelihood that high interior
temperatures will cause the camera’s sensing
system to shut off, when parking, find a shady
area or face the front of the vehicle away from
the sun. If you use a reflective sun shade, do
not allow it to cover the camera housing.
Covering the camera can concentrate heat on
it.
■
Camera Location and Handling Tips
1
Never apply a film or attach any objects to the
windshield, the hood, or the front grille that could
obstruct the camera’s field of vision and cause the
system to operate abnormally.
Scratches, nicks, and other damage to the windshield
within the camera’s field of vision can cause the
system to operate abnormally. If this occurs, we
recommend that you replace the windshield with a
genuine Honda replacement windshield. Making
even minor repairs within the camera’s field of vision
or installing an aftermarket replacement windshield
may also cause the system to operate abnormally.
After replacing the windshield, have a dealer
recalibrate the camera. Proper calibration of the
camera is necessary for the system to operate
properly.
Do not place an object on the top of the instrument
panel. It may reflect onto the windshield and prevent
the system from detecting lane lines properly.
Front Sensor
Camera
uu
Honda Sensing
®
u
Front Sensor Camera
466
Driving
1
If the
Some Driver Assist Systems Cannot
Operate
message appears:
•
Use the climate control system to cool down the
interior and, if necessary, also use defroster mode
with the airflow directed towards the camera.
•
Start driving the vehicle to lower the windshield
temperature, which cools down the area around
the camera.
If the
Some Driver Assist Systems Cannot
Operate
message appears:
•
Park your vehicle in a safe place, and clean the
windshield. If the message does not disappear after
you have cleaned the windshield and driven for a
while, have your vehicle checked by a dealer.
467
uu
Honda Sensing
®
u
Radar Sensor
Driving
Radar Sensor
The radar sensor is behind the emblem.
1
Avoid strong impacts to the front grille.
For the CMBS
TM
to work properly:
Always keep the front grille clean.
Never use chemical solvents or polishing powder for
cleaning the front grille. Clean it with water or a mild
detergent.
Do not put a sticker on the front grille or replace the
front grille.
If you need the radar sensor to be repaired, or
removed, or the front grille is strongly impacted, turn
off the system by using the safety support switch and
take your vehicle to a dealer.
2
If the vehicle is involved in any of the following
situations, the radar sensor may not work properly.
Have your vehicle checked by a dealer:
•
Your vehicle is involved in a frontal collision
•
Your vehicle drives through deep water or is
submerged in deep water
•
Your vehicle strongly strikes a bump, curb, chock,
or embankment that could jar the radar sensor
Radar Sensor
468
Driving
Braking
Brake System
Use the parking brake to keep the vehicle stationary when parking.
To apply:
Depress the parking brake pedal down with
your foot.
To release:
1.
Depress the brake pedal.
2.
Depress the parking brake.
■
Parking Brake
1
NOTICE
Release the parking brake fully before driving. The
rear brakes and axle can be damaged if you drive
with the parking brake applied.
If you start driving without fully releasing the parking
brake, a buzzer sounds as a warning, and
Release
Parking Brake
appears on the multi-information
display.
Always apply the parking brake when parking.
469
uu
Braking
u
Brake System
Driving
Your vehicle is equipped with disc brakes at all four wheels. A vacuum power assist
helps reduce the effort needed on the brake pedal. The brake assist system increases
the stopping force when you depress the brake pedal hard in an emergency
situation. The anti-lock brake system (ABS) helps you retain steering control when
braking very hard.
2
2
■
Foot Brake
1
Check the brakes after driving through deep water,
or if there is a buildup of road surface water. If
necessary, dry the brakes by lightly depressing the
pedal several times.
If you hear a continuous metallic friction sound when
applying the brakes, this is caused by the brake wear
indicator rubbing on the brake rotor and indicates
that the brake pads need to be replaced. Have the
vehicle checked by a dealer. If you hear only an
occasional squeak or squeal when you initially apply
the brake pedal, this may be normal and caused by
high frequency vibration of the brake pads against
the rotating brake disc.
Constantly using the brake pedal while going down a
long hill builds up heat, which reduces the brake
effectiveness. Apply engine braking by taking your
foot off the accelerator pedal and downshifting to a
lower gear.
Do not rest your foot on the brake pedal while
driving, as it will lightly apply the brakes and cause
them to lose effectiveness over time and reduce pad
life. It will also confuse drivers behind you.
470
uu
Braking
u
Anti-lock Brake System (ABS)
Driving
Anti-lock Brake System (ABS)
Helps prevent the wheels from locking up, and helps you retain steering control by
pumping the brakes rapidly, much faster than you can.
The electronic brake distribution (EBD) system, which is part of the ABS, also
balances the front-to-rear braking distribution according to vehicle loading.
You should never pump the brake pedal. Let the ABS work for you by always
keeping firm, steady pressure on the brake pedal. This is sometimes referred to as
“stomp and steer.”
■
ABS operation
The brake pedal may pulsate slightly when the ABS is working. Depress the brake
pedal and keep holding the pedal firmly down. On dry pavement, you will need to
press on the brake pedal very hard before the ABS activates. However, you may feel
the ABS activate immediately if you are trying to stop on snow or ice.
ABS may activate when you depress the brake pedal when driving on:
•
Wet or snow covered roads.
•
Roads paved with stone.
•
Roads with uneven surfaces, such as potholes, cracks, manholes, etc.
When the vehicle speed goes under 6 mph (10 km/h), the ABS stops.
■
ABS
1
NOTICE
The ABS may not function correctly if you use a tire of
the incorrect size or type.
If the
ABS
indicator comes on while driving, there
may be a problem with the system.
While normal braking will not be affected, there is a
possibility that the ABS will not be operating. Have
your vehicle checked by a dealer immediately.
The ABS is not designed for the purpose of reducing
the time or distance it takes for a vehicle to stop: It is
designed to limit brake lockup which can lead to
skidding and loss of steering control.
In the following cases, your vehicle may need more
distance to stop than a vehicle without the ABS:
•
You are driving on rough or uneven road surfaces,
such as gravel or snow.
•
The tires are equipped with tire chains.
The following may be observed with the ABS system:
•
Motor sounds coming from the engine
compartment when the brakes are applied, or
when system checks are being performed after the
engine has been started and while the vehicle
accelerates.
•
Brake pedal and/or the vehicle body vibration when
ABS activates.
These vibrations and sounds are normal to ABS
systems and are no cause for concern.
471
uu
Braking
u
Brake Assist System
Driving
Brake Assist System
Designed to assist the driver by generating greater braking force when you depress
the brake pedal hard during emergency braking.
■
Brake assist system operation
Press the brake pedal firmly for more powerful braking.
When brake assist operates, the pedal may wiggle slightly and an operating noise
may be heard. This is normal. Keep holding the brake pedal firmly down.
472
Driving
Parking Your Vehicle
When Stopped
1.
Depress the brake pedal firmly.
2.
Apply the parking brake.
3.
Put the transmission into
(
P
.
4.
Turn off the engine.
Always set the parking brake, in particular if you are parked on an incline.
1
Do not park your vehicle near flammable objects,
such as dry grass, oil, or timber.
Heat from the exhaust can cause a fire.
3
WARNING
The vehicle can roll away if left unattended
without confirming that Park is engaged.
A vehicle that rolls away could cause a crash
resulting in serious injury or death.
Always keep your foot on the brake pedal
until you have confirmed that
(
P
is shown
on the shift position Indicator.
1
NOTICE
The following can damage the transmission:
•
Depressing the accelerator and brake pedals
simultaneously.
•
Holding the vehicle in place when facing uphill by
depressing the accelerator pedal.
•
Putting the transmission into
(
P
before the vehicle
stops completely.
In extremely cold temperatures, the parking brake
may freeze up if applied. If such temperatures are
expected, do not apply the parking brake but, if
parking on a slope, either turn the front wheels so
they will contact the curb if the vehicle rolls down the
slope or block the wheels to keep the vehicle from
moving. If you do not take either precaution, the
vehicle may roll unexpectedly, leading to a crash.
473
uu
Parking Your Vehicle
u
Parking Sensor System
*
Continued
Driving
Parking Sensor System
*
The corner and center sensors monitor obstacles around your vehicle, and the
beeper, multi-information display and audio/information screen let you know the
approximate distance between your vehicle and the obstacle.
■
The sensor location and range
1
Even when the system is on, always confirm if there is
no obstacle near your vehicle before parking.
The system may not work properly when:
•
The sensors are covered with snow, ice, mud, or
dirt.
•
The vehicle is on uneven surface, such as grass,
bumps, or a hill.
•
The vehicle has been out in hot or cold weather.
•
The system is affected by devices that emit
ultrasonic waves.
•
Driving in bad weather.
The system may not sense:
•
Thin or low objects.
•
Sonic-absorptive materials, such as snow, cotton,
or sponge.
•
Objects directly under the bumper.
Do not put any accessories on or around the sensors.
Front: Within about 24 in (60 cm) or less
Rear: Within about 27 in (70 cm) or less
Front Corner Sensors
Rear Corner Sensors
Rear Center Sensors
Within about 47 in (120 cm) or less
* Not available on all models
uu
Parking Your Vehicle
u
Parking Sensor System
*
474
Driving
■
Parking sensor system on and off
With the power mode in ON, press the
parking sensor system button to turn on or off
the system. The indicator in the button comes
on when the system is on.
The front corner, rear center and corner
sensors start to detect an obstacle when the
transmission is in
(
R
, and the vehicle speed is
less than 5 mph (8 km/h).
The front corner sensors start to detect an
obstacle when the transmission is not in
(
P
,
and the vehicle speed is less than 5 mph (8
km/h).
1
When you set the power mode to ON, the system will
be in the previously selected condition.
Indicator
* Not available on all models
475
uu
Parking Your Vehicle
u
Parking Sensor System
*
Continued
Driving
■
When the distance between your vehicle and detected obstacles becomes shorter
*1: At this stage, only the center sensors detect obstacles.
Interval between
beeps
Distance between the Bumper and Obstacle
Indicator
Multi-Information Display/
Audio/information screen
Corner Sensors
Center Sensors
Moderate
—
Rear: About 47-27 in
(120-70 cm)
Blinks in Yellow
*1
Short
Front: About 24-18 in
(60-45 cm)
Rear: About 27-22 in
(70-55 cm)
Rear: About 27-22 in
(70-55 cm)
Blinks in Amber
Very short
Front: About 18-14 in
(45-35 cm)
Rear: About 22-18 in
(55-45 cm)
Rear: About 22-18 in
(55-45 cm)
Continuous
Front: About 14 in
(35 cm) or less
Rear: About 18 in
(45 cm) or less
Rear: About 18 in
(45 cm) or less
Blinks in Red
Indicators light up where the
sensor detects an obstacle
Audio/Information Screen
Multi-Information Display
Indicators light up where the
sensor detects an obstacle
uu
Parking Your Vehicle
u
Parking Sensor System
*
476
Driving
1.
Make sure that the parking sensor system is not activated. Set the power mode to
VEHICLE OFF.
2.
Press and hold the parking sensor system button, and set the power mode to ON.
3.
Keep pressing the button for 10 seconds. Release the button when the indicator
in the button flashes.
4.
Press the button again. The indicator in the button goes off.
u
The beeper sounds twice. The rear sensors are now turned off.
To turn the rear sensors on again, follow the above procedure. The beeper sounds
three times when the rear sensors come back on.
■
Turning off All Rear Sensors
1
When you shift to
(
R
, the indicator in the parking
sensor system button blinks as a reminder that the
rear sensors have been turned off.
477
uu
Parking Your Vehicle
u
Cross Traffic Monitor
*
Continued
Driving
Cross Traffic Monitor
*
Monitors the rear corner areas using the radar sensors when reversing, and alerts
you if a vehicle approaching from a rear corner is detected.
The system is convenient when you are backing out of a parking space.
1
The parking sensor system’s alerting buzzer overrides
the Cross Traffic Monitor buzzer when the sensors
are detecting obstacles at the closest range.
3
CAUTION
Cross Traffic Monitor cannot detect all
approaching vehicles and may not detect
an approaching vehicle at all.
Failure to visually confirm that it is safe to
back up the vehicle before doing so may
result in a collision.
Do not solely rely on the system when
reversing; always also use your mirrors, and
look behind and to the sides of your vehicle
before reversing.
Models with parking sensor system
* Not available on all models
uu
Parking Your Vehicle
u
Cross Traffic Monitor
*
478
Driving
The system activates when:
•
The power mode is in ON.
•
The Cross Traffic Monitor is turned on.
2
Cross Traffic Monitor On and Off
•
The transmission is in
(
R
.
•
Your vehicle is moving at 3 mph (5 km/h) or
lower.
When a vehicle is detected approaching from a rear corner, Cross Traffic Monitor
alerts you with a buzzer and a displayed warning.
The system will not detect a vehicle that approaches from directly behind your
vehicle, nor will it provide alerts about a detected vehicle when it moves directly
behind your vehicle.
The system does not provide alerts for a vehicle that is moving away from your
vehicle, and it may alert for pedestrians, bicycles, or stationary objects.
■
How the System Works
1
Cross Traffic Monitor may not detect or may delay
alerting an approaching vehicle, or may alert without
an approaching vehicle under the following
conditions:
•
An obstacle, such as another vehicle and a wall,
near your vehicle’s rear bumper, is blocking the
radar sensor’s scope.
•
Your vehicle is moving at the speed of about 3 mph
(5 km/h) or higher.
•
A vehicle is approaching at the speed other than
between about 6 mph (10 km/h) and 16 mph
(25 km/h).
•
The system picks up external interference such as
other radar sensors from another vehicle or strong
radio wave transmitted from a facility nearby.
•
Either corner of the rear bumper is covered with
snow, ice, mud or dirt.
•
When there is bad weather.
•
Your vehicle is on an incline.
•
Your vehicle is tilted due to a heavy load in the rear.
•
Your vehicle is reversing towards a wall, a pole, a
vehicle, and so on.
The rear bumper or the sensors have been improperly
repaired or the rear bumper has been deformed.
Have your vehicle checked by a dealer.
For proper operation, always keep the rear bumper
corner area clean.
Do not cover the rear bumper corner area with labels
or stickers of any kind.
Radar sensors:
Underneath the rear bumper
corners
* Not available on all models
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст