Honda Ridgeline. Manual — part 19
01
SJC8A00A14100022205KBAT01
01
SJC8A00A14100022208KBAT10
4-33
4-33
Drive Belt Auto-tensioner
Replacement
Tensioner Pulley Replacement
10 x 1.25 mm
45 N·m (4.5 kgf·m, 33 lbf·ft)
8 x 1.25 mm
22 N·m (2.2 kgf·m, 16 lbf·ft)
A
10 x 1.5 mm
80 N·m (8.2 kgf·m, 59 lbf·ft)
B
1. Remove the drive belt (see page 4-31).
2. Remove the splash shield (see step 30 on page 5-5).
3. Remove the auto-tensioner.
4. Install the auto-tensioner in the reverse order of
removal.
1. Remove the auto-tensioner (see page 4-33).
2. Remove the pulley bolt (A) (left-hand threads), and
remove the tensioner pulley (B).
3. Install the tensioner pulley in the reverse order of
removal.
01
02
SJC8A00A14100012901KDAT20
Removal
4-34
Charging System
Alternator Removal and Installation
A
B
C
D
E
A
B
1. Make sure you have anti-theft codes for the audio
system and the navigation system (if equipped).
2. Disconnect the negative cable from the battery.
3. Remove the engine manifold cover (see step 1 on
page 4-19).
4. Remove the drive belt (see page 4-31).
5. Remove the harness clamp (A) and harness clamp
bracket (B), then remove the harness holder (C).
6. Disconnect the alternator connector (D) and the
BLK wire (E) from the alternator.
7. Remove the mounting bolt (A) and alternator
bracket mounting bolt (B), then remove the
alternator.
01
04
Installation
4-35
8 x 1.25 mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
10 x 1.25 mm
45 N·m
(4.5 kgf·m, 33 lbf·ft)
8 x 1.25 mm
12 N·m
(1.2 kgf·m,
8.7 lbf·ft)
6 x 1.0 mm
12 N·m (1.2 kgf·m, 8.7 lbf·ft)
E
D
6 x 1.0 mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
C
B
A
1. Install the alternator.
2. Connect the alternator connector (A) and the BLK
wire (B) to the alternator.
3. Install the harness holder (C), then install the
harness clamp bracket (D) and harness clamp (E).
4. Install the drive belt (see page 4-31).
5. Install the engine cover (see step 1 on page 4-19).
6. Connect the negative cable.
7. Enter the anti-theft codes for the audio system and
navigation system (if equipped).
8. Do the power window control unit reset procedure
(see page 22-209).
9. Set the clock (on vehicles without navigation).
01
SJC8A00A14100012901LAAT00
Exploded View
4-36
Charging System
Alternator Overhaul
ROTOR
BEARING RETAINER
FRONT BEARING
DRIVE-END HOUSING
PULLEY
PULLEY LOCKNUT
REAR HOUSING ASSEMBLY
BRUSH HOLDER
ASSEMBLY
END COVER
TERMINAL INSULATOR
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст