Honda Ridgeline. Manual — part 497
*01
SJC8A00J46127000000DAAT55
22-284
Power Seats
Component Location Index
DRIVER’S SEAT
FRONT UP-DOWN MOTOR
RECLINE MOTOR
REAR UP-DOWN MOTOR
POWER SEAT ADJUSTMENT SWITCH
SLIDE MOTOR
Test, page 22-287
Test, page 22-287
Test, page 22-287
Test/Replacement, page 22-286
Test, page 22-287
*01
SJC8A00J46127000000EAAT00
−
−
−
−
−
−
−
−
22-285
Circuit Diagram
B1
B6
BLK/YEL
F11
F13
G501
2
1
2
1
REAR UP DOWN MOTOR
RECLINE MOTOR
SLIDE MOTOR
FRONT UP DOWN MOTOR
2
1
2
1
4
WHT
6
YEL
12
BLU/ORN
1
ORN
5
YEL/RED
11
BRN
7
LT GRN
3
BLK
UP
DOWN
2
8
9
10
LT BLU
DRIVER’S POWER SEAT ADJUSTMENT SWITCH
DOWN
UP
BLU
WHT/RED
WHT/BLU
(20 A)
No.16
BLK
G501
No.14
(20 A)
No.22 (SEAT) (40 A)
BATTERY
UNDER DASH
FUSE/RELAY
BOX
BACK
WARD
FOR
WARD
FOR
WARD
BACK
WARD
UNDER HOOD
FUSE/RELAY BOX
01
02
SJC8A00J46127046701FHAT55
22-286
Power Seats
Power Seat Adjustment Switch Test/Replacement
B
A
Terminal
Position
SLIDE
SWITCH
RECLINE
SWITCH
FRONT
UP-DOWN
SWITCH
REAR
UP-DOWN
SWITCH
1
10
11
12
Forward
Backward
UP
DOWN
Forward
Backward
UP
DOWN
2
4
3
5
6
7
8
9
1. Remove the power seat adjustment switch knobs (A) and recline cover from the driver’s power seat (see step 7 on
page 20-101), then remove the two screws and the power seat adjustment switch (B).
2. Disconnect the 12P connector from the power seat adjustment switch.
3. Reinstall the adjustment switch knobs to the switch.
4. Check for continuity between the terminals in each switch position according to the table.
5. If the continuity is not as specified, replace the switch.
01
02
03
04
05
SJC8A00J46127046501FEAT55
Slide motor
Recline motor
Front up-down motor
Rear up-down motor
22-287
Motor Test
A
B
Forward
Backward
Terminal
Position
7
11
Forward
Backward
Terminal
Position
6
12
UP
DOWN
Terminal
Position
3
9
UP
DOWN
Terminal
Position
1
5
1. Remove the driver’s seat (see page 20-97).
2. Remove the power seat adjustment switch knobs
and recline cover from the seat (see step 7 on page
20-101).
3. Disconnect the 12P connector (A) from the power
seat adjustment switch (B).
4. Test each motor by applying battery voltage and
body ground to the 12P connector terminals.
5. If the motor does not run or fails to run smoothly,
check for an open in the driver’s seat wire harness
and recline motor subharness. If the harness is OK,
replace the motor.
• Recline motor (see page 20-103).
• Other motors:
– ’06 model (see page 20-108)
– ’07-08 models (see page 20-109)
Wire side of
female terminals
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст