Honda Ridgeline. Manual — part 489
*92
−
−
22-252
Gauges
Circuit Diagram (cont’d)
1
•
•
L
K
I
J
C15
BLU/BLK
DRIVE CIRCUIT
B7
BLK/YEL
LT GRN
A14
GAUGE CONTROL MODULE
GRN/ORN
INTERFACE
GRN/ORN
GRN/ORN
INTERFACE
B9
B2
GRN/RED
BLK
G301
G402
BLK
C10
BRAKE FLUID
LEVEL SWITCH
(Closed : Float down)
(Open : Float up)
PARKING
BRAKE
SWITCH
(Closed : Pedal pressed)
(Open : Pedal released)
VTM 4
CONTROL UNIT
POWER SUPPLY CIRCUIT/CONTROLLER AREA
NETWORK CONTROLLER
BRAKE
SYSTEM
INDICATOR
(LED)
CRUISE
CONTROL
MAIN
SWITCH
SECURITY
INDICATOR
CARGO AREA
LIGHT RELAY
CARGO
AREA
LIGHT
INDICATOR
(LED)
IMMOBILIZER
CONTROL
UNIT RECEIVER
*92
−
−
−
−
22-253
*2 : ’07 08 models
*1 : ’06 model
GRN*
PNK/BLU*
C3
RED/WHT
BRN
GAUGE CONTROL MODULE
A10
BLK
C2
C19
RED/BLU
BRN
RED/BLU
RED/BLU
BRN
G401
PNK/BLU
C16
SIDE AIRBAG
CUTOFF
INDICATOR
(LED)
RIGHT TURN
SIGNAL
INDICATOR
(LED)
LEFT TURN
SIGNAL
INDICATOR
(LED)
LEFT TURN
SIGNAL LIGHTS
RIGHT TURN
SIGNAL LIGHTS
VTM 4
INDICATOR
(LED)
VTM 4
CONTROL
UNIT
TURN SIGNAL/HAZARD RELAY
(Built in the
under dash fuse/relay box)
OPDS/ODS
UNIT
1
2
SJC8A00K732000Y1152FAAT00
SJC8A00K732000Y1155FAAT00
−
−
−
−
−
−
−
−
DTC B1152:
DTC B1155:
DTC B1156:
YES
NO
YES
NO
YES
NO
YES
NO
22-254
22-254
Gauges
DTC Troubleshooting
Gauge Control Module Internal
Error (EEPROM Error)
Gauge Control Module Lost
Communication with the Combination
Switch Control Unit (HLSW Message)
Gauge Control Module Lost
Communication with the Combination
Switch Control Unit (WIPSW Message)
NOTE: If you are troubleshooting multiple DTCs, be
sure to follow the instructions in B-CAN System
Diagnosis Test Mode A (see page 22-99).
1. Clear the DTCs with the HDS.
2. Turn the ignition switch OFF, and then back ON (II).
3. Wait for 6 seconds or more.
4. Check for DTCs with the HDS.
Go to step 5.
Intermittent failure. The gauge control
module is OK at this time. Check for loose or poor
connections. If the connections are good, check the
battery condition (see page 22-74), and the
charging system.
5. Disconnect the gauge control module connectors,
then reconnect them.
6. Check for DTCs with the HDS.
Faulty gauge control module; replace the
gauge control module (see page 22-263).
Intermittent failure. The gauge control
module is OK at this time. Check for loose or poor
connections. If the connections are good, check the
battery condition (see page 22-74), and the
charging system.
NOTE: If you are troubleshooting multiple DTCs, be
sure to follow the instructions in B-CAN System
Diagnosis Test Mode A (see page 22-99).
1. Clear the DTCs with the HDS.
2. Turn the ignition switch OFF, and then back ON (II).
3. Wait for 6 seconds or more.
4. Check for DTCs with the HDS.
Go to step 5.
Intermittent failure. The gauge control
module is OK at this time. Check for loose or poor
connections.
5. Check for DTCs with the HDS.
Go to combination switch control unit input
test (see page 22-124).
Go to gauge control module input test
(see page 22-122).
Is DT C B1152 indicated?
Is DT C B1152 still indicated?
Aer DT Cs B1155 and/ or B1156 indicated?
Ar e DT Cs B1007 , B1062, and B1063 also
indicated?
SJC8A00K732000Y1157FAAT00
SJC8A00K732000Y1158FAAT00
−
−
−
−
−
−
−
−
DTC B1157:
DTC B1159:
DTC B1158:
YES
NO
YES
NO
YES
NO
YES
NO
22-255
22-255
Gauge Control Module Lost
Communication with MICU (MICU Message)
Gauge Control Module Lost
Communication with MICU (DOORSW
Message)
Gauge Control Module Lost
Communication with Relay Control Module
(RM Message)
NOTE: If you are troubleshooting multiple DTCs, be
sure to follow the instructions in B-CAN System
Diagnosis Test Mode A (see page 22-99).
1. Clear the DTCs with the HDS.
2. Turn the ignition switch OFF, and then back ON (II).
3. Wait for 6 seconds or more.
4. Check for DTCs with the HDS.
Go to step 5.
Intermittent failure. The gauge control
module is OK at this time. Check for loose or poor
connections.
5. Check for DTCs with the HDS.
Go to MICU input test (see page 22-117).
Go to gauge control module input test
(see page 22-122).
NOTE: If you are troubleshooting multiple DTCs, be
sure to follow the instructions in B-CAN System
Diagnosis Test Mode A (see page 22-99).
1. Clear the DTCs with the HDS.
2. Turn the ignition switch OFF, and then back ON (II).
3. Wait for 6 seconds or more.
4. Check for DTCs with the HDS.
Go to step 5.
Intermittent failure. The gauge control
module is OK at this time. Check for loose or poor
connections.
5. Check for DTCs with the HDS.
Go to relay control module input test
(see page 22-125).
Go to gauge control module input test
(see page 22-122).
Ar e DT Cs B1157 and/ or B1159 indicated?
Ar e DT Cs B1055, B1057 , B1105, B1106, and
B1255 also indicated?
Is DT C B1158 indicated?
Is DT C B1005 also indicated?
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст