Honda Ridgeline. Manual — part 576
−
03
04
−
−
−
−
YES
NO
YES
NO
24-129
DRIVER’S SEAT BELT BUCKLE SWITCH
3P CONNECTOR
BLU
BLK
BLK
GRY
DRIVER’S SEAT BELT BUCKLE SWITCH
3P CONNECTOR
BLU
GRY
7. Unbuckle the driver’s seat belt.
• Measure the resistance between the No. 1 and
No. 2 terminals of the driver’s seat belt buckle
switch 3P connector. There should be 0
1
.
• Measure the resistance between the No. 1 and
No. 3 terminals of the same connector. There
should be an open circuit or at least 1 M
.
Go to step 8.
Replace the driver’s seat belt buckle assembly
(see page 24-6), then clear the DTC.
8. Measure the resistance between the No. 2 terminal
of the driver’s seat belt buckle switch 3P connector
and body ground, and between the No. 3 terminal
and body ground. There should an open circuit or
at least 1 M
.
Go to step 9.
Replace the driver’s seat belt buckle assembly
(see page 24-6).
9. Disconnect the negative cable from the battery.
10. Disconnect both seat belt tensioner 4P connectors
from the floor wire harness (see step 6 on page
24-26).
11. Disconnect SRS unit connector B (28P) from the
SRS unit (see step 7 on page 24-26).
(cont’d)
Terminal side of male terminals
Terminal side of male terminals
Terminal side of male terminals
Ar e the r esistances as specif ied?
Is the r esistance as specif ied?
05
06
−
−
−
−
YES
NO
YES
NO
24-130
SRS
DTC Troubleshooting (cont’d)
DRIVER’S SEAT WIRE HARNESS or
FLOOR WIRE HARNESS 3P CONNECTOR
BLU/RED
DRIVER’S SEAT WIRE HARNESS or
FLOOR WIRE HARNESS 3P CONNECTOR
LT GRN
12. Measure the resistance between the No. 2 terminal
of the driver’s seat wire harness or floor wire
harness 3P connector and body ground. There
should be an open circuit or at least 1 M
.
Check the connections at the floor wire
harness, connector F (14P), and connector H (14P)
at the under-dash fuse/relay box (see page 22-61).
If the connections are OK, go to step 13.
Short to ground in the driver’s seat wire
harness, floor wire harness, or the MICU/under-
dash fuse/relay box. Replace the faulty harness or
part.
13. Measure the resistance between the No. 3 terminal
of the driver’s seat wire harness or floor wire
harness 3P connector and body ground. There
should be an open circuit or at least 1 M
.
Faulty SRS unit; replace the SRS unit
(see page 24-188).
Short to ground in the driver’s seat wire
harness or floor wire harness; replace the faulty
harness.
Wire side of female terminals
Wire side of female terminals
Is the r esistance as specif ied?
Is the r esistance as specif ied?
−
01
02
SJC8A00K791000R621XFAAT00
−
−
−
−
DTC 62-1x (‘‘x’’ can be 0 thru 9 or A thru F):
YES
NO
YES
NO
24-131
A
FRONT PASSENGER’S SEAT BELT
BUCKLE SWITCH 3P CONNECTOR
BLU
BLK
BLK
GRY
Open in Front Passenger’s Seat Belt Buckle
Switch
NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-16) and General Troubleshooting Information
(see page 24-27).
1. Clear the DTC memory (see page 24-28).
2. Turn the ignition switch ON (II), then buckle and
unbuckle the front passenger’s seat belt several
times.
3. Read the DTC (see page 24-27).
Go to step 4.
Intermittent failure, the system is OK at this
time. Go to Troubleshooting Intermittent Failures
(see page 24-29). If another DTC is indicated,
troubleshoot the DTC.
4. Turn the ignition switch OFF.
5. Disconnect the front passenger’s seat belt buckle
switch 3P connector (A) from the passenger’s seat
wire harness.
6. Buckle the front passenger’s seat belt.
• Measure the resistance between the No. 1 and
No. 3 terminals of the front passenger’s seat belt
buckle switch 3P connector. There should be
0
1
.
• Measure the resistance between the No. 1 and
No. 2 terminals of the same connector. There
should be an open circuit or at least 1 M
.
Go to step 7.
Replace the front passenger’s seat belt buckle
assembly (see page 24-6), then clear the DTC.
(cont’d)
Terminal side of male terminals
Terminal side of male terminals
Is DT C 62-1x indicated?
Ar e the r esistances as specif ied?
−
−
−
03
04
−
−
−
−
YES
NO
YES
NO
24-132
SRS
DTC Troubleshooting (cont’d)
BLU
BLK
BLK
GRY
FRONT PASSENGER’S SEAT BELT
BUCKLE SWITCH 3P CONNECTOR
PASSENGER’S SEAT
WIRE HARNESS 3P CONNECTOR
BLK
7. Unbuckle the front passenger’s seat belt.
• Measure the resistance between the No. 1 and
No. 2 terminals of the front passenger’s seat belt
buckle switch 3P connector. There should be
0
1
.
• Measure the resistance between the No. 1 and
No. 2 terminals of the front passenger’s seat belt
buckle switch 3P connector. There should be
0
1
.
Go to step 8.
Replace the front passenger’s seat belt buckle
assembly (see page 24-6), then clear the DTC.
8. Measure the resistance between the No. 1 terminal
of the passenger’s seat wire harness 3P connector
and body ground. There should be 0
1
.
Go to step 9.
Open in the passenger’s seat wire harness or
floor wire harness, or poor ground connection at
G501 (see page 22-38). If G501 is OK, replace the
faulty harness.
9. Disconnect the negative cable from the battery.
10. Disconnect both seat belt tensioner 4P connectors
from the floor wire harness (see step 6 on page
24-26).
11. Disconnect SRS unit connector B (28P) from the
SRS unit (see step 7 on page 24-26).
Terminal side of male terminals
Terminal side of male terminals
Wire side of female terminals
Ar e the r esistances as specif ied?
Is the r esistance as specif ied?
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст