Honda Ridgeline. Manual — part 237
01
02
03
SJC8A00E10411310601KBAT02
Special Tools Required
14-333
1st Clutch Hub Replacement
A
B
C
07749-0010000
07947-6340500
A
B
C
A or B
A or B
A
B
07749-0010000
07GAD-SD40101
• Driver 07749-0010000
• Driver attachment 07947-6340500
• Attachment, 78 x 80 mm 07GAD-SD40101
1. Remove the 1st-hold clutch hub (A) from the 1st
gear (B) with the driver, driver attachment, and a
press.
2. Remove the 1st clutch hub (C) from the 1st gear.
3. Install the new 1st clutch hub (A) over the 1st gear
(B), and install the 1st-hold clutch hub (C) in the 1st
gear.
NOTE: If the 1st gear and the 1st-hold clutch hub
are replaced, use the 1st gear and the 1st-hold
clutch hub with the same identifying letters (A or B).
4. Install the 1st-hold clutch hub (A) in the 1st gear (B)
with the driver, attachment (78 x 80 mm), and the
press.
01
02
SJC8A00E10411300000LDAT01
Special Tools Required
14-334
Shafts and Clutches
Secondary Shaft Reassembly
A
B
C
D
E
F
G
H
I
A
B
C
D
F
G
H
I
J
K
E
• Driver, 40 mm I.D. 07746-0030100
• Attachment, 30 mm I.D. 07746-0030300
• Wrench, 40 x 42 mm 07XAA-002010A
1. Install the thrust needle bearing (A), the needle
bearings (B), the 2nd gear/park gear (C), the thrust
needle bearing (D), and the splined washer (E) in
the direction shown on the secondary shaft (F).
2. Wrap the shaft splines with tape, and install new
O-rings (G) in the 2nd clutch O-ring grooves, then
remove the tape.
NOTE: To prevent damage to the O-rings, be sure
to install the O-rings after installing the splined
washer.
3. Install the 2nd clutch (H) on the secondary shaft,
and secure the 2nd clutch with the snap ring (I).
4. Install the idler gear (A) in the direction shown, the
thrust needle bearing (B), the 1st gear collar (C), the
needle bearing (D), the 1st gear assembly (E), the
thrust needle bearing (F), and the 52 mm washer
(G) in the direction shown on the secondary shaft
(H).
5. Wrap the shaft splines with tape, and install new
O-rings (J) in the 1st/1st-hold clutch O-ring grooves,
then remove the tape.
NOTE: To prevent damage to the O-rings, be sure
to install the O-rings after installing the 1st gear
collar and the 52 mm washer.
6. Install the 1st/1st-hold clutch (K).
two cavities (I) without rollers.
NOTE: It is normal for the needle bearing (D) to have
03
04
*01
06
14-335
A
B
07746-0030100
07746-0030300
07746-0030100
07746-0030300
A
B
A
A
B
C
D
07XAA-002010A
7. Install the ball bearing (A) over the 1st/1st-hold
clutch guide (B) with the driver (40 mm I.D.),
attachment (30 mm I.D.), and a press.
8. Install the new splined washer (A) with the marked
side (B) up over the ball bearing with the driver
(40 mm I.D.), attachment (30 mm I.D.), and the
press.
9. Install the new locknut (A).
10. Place a V-block (A) on a vise (B), and put the
secondary shaft (C) on the V-block and vise.
11. Attach the wrench (40 x 42 mm), onto the top of the
1st clutch guide, and secure the wrench
(40 x 42 mm), with the vise to hold the secondary
shaft. Tighten the locknut to 178 N·m (18.2 kgf·m,
132 lbf·ft) with the torque wrench (D).
NOTE:
• Use a torque wrench to tighten the locknut. Do
not use an impact wrench.
• The locknut has left-hand threads.
(cont’d)
−
−
07
14-336
Shafts and Clutches
Secondary Shaft Reassembly (cont’d)
A
B
12. Stake the locknut into the shaft to a depth (A) of
0.7
1.3 mm (0.03
0.05 in.) using a 3.5 mm punch
(B).
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст