Honda Ridgeline. Manual — part 178
02
*01
−
−
−
−
YES
NO
YES
NO
14-97
INPUT SHAFT (MAINSHAFT)
SPEED SENSOR CONNECTOR
VCC2 (YEL/BLU)
PCM CONNECTOR C (44P)
INPUT SHAFT
(MAINSHAFT)
SPEED SENSOR
CONNECTOR
VCC2
(YEL/BLU)
VCC2 (YEL/BLU)
11. Connect PCM connectors B (44P) and C (44P).
12. Turn the ignition switch to ON (II).
13. Measure the voltage between input shaft
(mainshaft) speed sensor connector terminal No. 1
and body ground.
Go to step 19.
Go to step 14.
14. Turn the ignition switch to LOCK (0).
15. Jump the SCS line with the HDS.
16. Disconnect PCM connector C (44P).
17. Check for continuity between PCM connector
terminal C13 and input shaft (mainshaft) speed
sensor connector terminal No. 1.
Go to step 18.
Repair an open in the wire between PCM
connector terminal C13 and the input shaft
(mainshaft) speed sensor, then go to step 37.
(cont’d)
Wire side of female terminals
Wire side of
female terminals
Terminal side of
female terminals
Is ther e about 5 V ?
Is ther e continuity?
04
05
−
−
−
−
YES
NO
YES
NO
14-98
Automatic Transmission
DTC Troubleshooting (cont’d)
PCM CONNECTOR C (44P)
VCC2 (YEL/BLU)
INPUT SHAFT (MAINSHAFT)
SPEED SENSOR CONNECTOR
NM (RED)
18. Check for continuity between PCM connector
terminal C13 and body ground.
Repair a short to ground in the wire between
PCM connector terminal C13 and the input shaft
(mainshaft) speed sensor, then go to step 37.
Go to step 44.
19. Turn the ignition switch to LOCK (0).
20. Jump the SCS line with the HDS.
21. Disconnect PCM connector B (44P).
22. Check for continuity between input shaft
(mainshaft) speed sensor connector terminal No. 2
and body ground.
Repair a short to ground in the wire between
PCM connector terminal B39 and the input shaft
(mainshaft) speed sensor connector, then go to
step 37.
Go to step 23.
Terminal side of female terminals
Wire side of female terminals
Is ther e continuity?
Is ther e continuity?
*02
07
−
−
−
−
YES
NO
YES
NO
14-99
PCM CONNECTOR C (44P)
INPUT SHAFT
(MAINSHAFT)
SPEED SENSOR
CONNECTOR
SG2 (GRN/YEL)
SG2
(GRN/YEL)
INPUT SHAFT (MAINSHAFT)
SPEED SENSOR CONNECTOR
NM (RED)
SG2 (GRN/YEL)
23. Disconnect PCM connector C (44P).
24. Check for continuity between PCM connector
terminal C14 and input shaft (mainshaft) speed
sensor connector terminal No. 3.
Go to step 25.
Repair an open in the wire between the input
shaft (mainshaft) speed sensor connector and PCM
connector terminal C14, then go to step 37.
25. Connect PCM connectors B (44P) and C (44P).
26. Turn the ignition switch to ON (II).
27. Measure the voltage between input shaft
(mainshaft) speed sensor connector terminals
No. 2 and No. 3.
Go to step 32.
Go to step 28.
(cont’d)
Wire side of
female terminals
Terminal side of
female terminals
Wire side of female terminals
Is ther e continuity?
Is ther e about 5 V ?
*03
−
−
−
−
YES
NO
YES
NO
14-100
Automatic Transmission
DTC Troubleshooting (cont’d)
PCM CONNECTOR B (44P)
INPUT SHAFT
(MAINSHAFT)
SPEED SENSOR
CONNECTOR
NM (RED)
NM (RED)
28. Turn the ignition switch to LOCK (0).
29. Jump the SCS line with the HDS.
30. Disconnect PCM connector B (44P).
31. Check for continuity between PCM connector
terminal B39 and input shaft (mainshaft) speed
sensor connector terminal No. 2.
Go to step 44.
Repair an open in the wire between PCM
connector terminal B39 and the input shaft
(mainshaft) speed sensor, then go to step 37.
32. Connect the input shaft (mainshaft) speed sensor
connector.
33. Clear the DTC with the HDS.
34. Start the engine, disable the VSA by pressing the
VSA OFF button, run the vehicle in D, and hold the
vehicle at speeds over 12 mph (20 km/h) for at least
10 seconds when the transmission is not shifting,
then slow down and stop the wheels.
35. Monitor the OBD STATUS for P0716 or P0717 in the
DTCs MENU with the HDS.
Go to step 36.
Go to step 44.
Wire side of
female terminals
Terminal side of
female terminals
Is ther e continuity?
Does the scr een indicate F AILED?
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст