Honda Ridgeline. Manual — part 22
Signal to be tested
Parameter: Desired result
Test condition
Possible cause if result is not obtained
4-45
•
•
•
Resume
switch signal
Resume/accel switch
pressed and released
CRUISE CONTROL
RESUME SW should
indicate ON when the
resume/accel switch is
pressed and OFF when
the resume/accel
switch is released.
Faulty cruise control set/decel, resume/
accel, cancel switch
An open in the wire between the gauge
control module and the cruise control
set/decel, resume/accel, cancel switch
A wire shorted to ground between the
gauge control module and the cruise
control set/decel, resume/accel, cancel
switch
Cancel switch
signal
Cancel switch
pressed and released
CRUISE CONTROL
CANCEL SW should
indicate ON when the
cancel switch is
pressed and OFF when
the cancel switch is
released.
Faulty cruise control set/decel, resume/
accel, cancel switch
Cruise control
indicator
signal
Start the engine, turn
the cruise control
main switch on and
drive the vehicle
above 25 mph
(40 km/h). Set and
cancel the cruise
control.
CRUISE INDICATOR
should indicate ON
when the cruise control
is set and OFF when
the cruise control is
canceled.
Faulty gauge control module
01
01
SJC8A00A14500017611FHAT01
01
02
SJC8A00A14500017621FHAT02
4-46
4-46
Cruise Control
Cruise Control Main Switch Test/
Replacement
Cruise Control Set/decel, Resume/
accel, Cancel Switch Test/
Replacement
A
B
Terminal
Position
OFF
ON
1
2
3
4
5
A
B
A
1. Release the clips of the cruise control main switch,
and push the cruise control main switch (A) out of
the driver’s dashboard lower cover.
2. Disconnect the 5P connector (B), then remove the
cruise control main switch.
3. Check for continuity between the terminals in each
switch position according to the table. If there is no
continuity, replace illumination bulbs (A) or the
switch.
SRS components are located in this area. Review the
SRS component locations (see page 24-14), and the
precautions and procedures (see page 24-16), in the
SRS before doing repairs or service.
1. Remove the driver’s airbag (see page 24-174).
2. Remove the steering wheel (see page 17-21).
3. Remove the steering wheel trim.
4. Disconnect the 7P connector (A), then remove the
cruise control set/decel, resume/accel, cancel
switch (B).
Terminal side of
male terminals
03
4-47
Terminal
Position
Set/decel (ON)
Resume/accel (ON)
Cancel (ON)
1
2
3
5. Check for continuity between the terminals in each
switch position according to the table.
• If there is continuity, and it matches the table, but
switch failure occurred on the cruise control
input test, check and repair the wire harness on
the switch circuit.
• If there is no continuity in one or more positions,
replace the switch.
Terminal side of male terminals
SJC8A000000000J0501ZCAT00
Engine Mechanical
Engine Assembly
. . . . . . . . . . . . ...
. . . . . . . . . . . . ...
Cylinder Head
. 6-1
. . . . . . . . . . . . .
. . . . . . . . . . . . .
Engine Block
. 7-1
. . . . . . . . . . ..
. . . . . . . . . . ..
Engine Lubrication
. 8-1
. . .
. . .
Intake Manifold and Exhaust System
. 9-1
. . . . . . . . . . . . . . ..
. . . . . . . . . . . . . ...
. . . . . . . . . ...
. . . . . . . . . . . . . . ..
. . . . . . . . . . . . . ...
. . . . . . . . . ...
Engine Removal
. 5-2
Engine Installation
. 5-12
Engine Mount Replacement
. 5-23
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст