Honda Ridgeline. Manual — part 463
03
01
SJC8A00J46660520703FEAT00
Rear Door (RTS, RTL, and EXL models)
22-148
22-148
Keyless/Power Door Locks/Security System
Door Lock Knob Switch Test
(cont’d)
Door Key Cylinder Switch Test
Not used
1. Remove the left or right rear door panel (see page
20-14).
2. Disconnect the 3P connector from the actuator.
3. Check for continuity between the terminals.
There should be continuity between the No. 1 and
No. 3 terminals when the door lock knob switch is
UNLOCK position and no continuity when the
switch is in the LOCK position.
4. If the continuity is not as specified, replace the door
lock actuator.
1. Remove the driver’s door panel (see page 20-7).
2. Disconnect the 3P connector from the key cylinder
switch.
3. Check for continuity between the terminals.
• There should be continuity between the No. 2
and No. 3 terminals when the door key cylinder
switch is in LOCK position.
• There should be no continuity between the No. 2
and No. 3 terminals when the door key cylinder
switch is in the neutral or UNLOCK position.
• There should be continuity between the No. 1
and No. 2 terminals when the door key cylinder
switch is in UNLOCK position.
• There should be no continuity between the No. 1
and No. 2 terminals when the door key cylinder
switch is in the neutral or LOCK position.
4. If the continuity is not as specified, replace the door
key cylinder assembly (see page 20-8).
01
SJC8A00J46660521021FEAT00
01
SJC8AGCJ46643432301FEAT00
Passenger’s Door Lock Switch
RTS, RTL, and EXL models
22-149
22-149
Door Lock Switch Test
Hood Switch Test
1. Remove the front passenger’s door panel (see page
20-7).
2. Check for continuity between the terminals.
• There should be continuity between the No. 2
and No. 9 terminals when the door lock switch is
in LOCK position. There should be no continuity
between the No. 2 and No. 9 terminals when the
door lock switch is in the neutral position.
• There should be continuity between the No. 1
and No. 9 terminals when the door lock switch is
in UNLOCK position. There should be no
continuity between the No. 1 and No. 9 terminals
when the door lock switch is in the neutral
position.
3. If the continuity is not as specified, replace the door
lock switch.
1. Open the hood.
2. Disconnect the 2P connector from the hood switch.
3. Check for continuity between the terminals.
There should be continuity between the No. 1 and
No. 2 terminals when the hood is opened (lever
released). There should be no continuity between
the No. 1 and No. 2 terminals when the hood is
closed (lever pushed down).
4. If the continuity is not as specified, replace the
hood latch (see page 20-185).
01
SJC8AGCJ46643454301FHAT10
01
SJC8AGCJ46643435241FEAT00
RTS, RTL, and EXL models
RTS, RTL, and EXL models
22-150
22-150
Keyless/Power Door Locks/Security System
Security Indicator Test/
Replacement
In-Bed Trunk Lid Key Cylinder
Switch Test
A
1. Remove the driver’s door panel (see page 20-7).
2. Remove the security indicator (A) from the door
panel.
3. Test the indicator by connecting battery power to
the No. 2 terminal and grounding the No.1 terminal.
The LED should come on.
4. If the LED does not come on, replace the security
indicator.
1. Remove the in-bed trunk lid inner cover (see step 2
on page 20-187).
2. Disconnect the 2P connector from the key cylinder
switch.
3. Check for continuity between the terminals.
There should be continuity between the No. 1 and
No. 2 terminals when the in-bed trunk lid key
cylinder switch is in UNLOCK position. There
should be no continuity between the No. 1 and
No. 2 terminals when the in-bed trunk lid key
cylinder switch is in the released (neutral) position.
4. If the continuity is not as specified, replace the in-
bed trunk lid key cylinder switch.
01
02
SJC8A00J46643436101FEAT00
With HDS
22-151
Transmitter Test
A
NOTE:
• If the doors unlock or lock with the transmitter, but
the LED on the transmitter does not come on, the LED
is faulty; replace the transmitter.
• If any door is open, you cannot lock the doors with
the transmitter.
• If you unlocked the doors with the transmitter, but do
not open any of the doors within 30 seconds, the
doors relock automatically.
• The doors do not lock or unlock with the transmitter if
the ignition key is inserted in the ignition switch.
1. Press the lock or unlock button five or six times to
reset the transmitter.
• If the locks work, the transmitter is OK.
• If any of the transmitter buttons do not work,
replace the transmitter, then reprogram and
register the transmitter (see page 22-324).
• If the locks don’t work, go to step 2.
2. Connect the HDS to the data link connector.
3. Select the KEYLESS from the BODY ELECTRICAL
menu, then enter the KEYLESS CHECK.
4. Press the lock, unlock, trunk, or panic button and
check the response on the screen of the HDS.
NOTE: The door lock actuators may or may not
cycle when receiving input from the transmitter.
• If KEYLESS ENTRY TRANSMITTER CODE IS
RECEIVED is indicated, the transmitter is OK.
• If DIFFERENT KEYLESS ENTRY TRANSMITTER
CODE IS RECEIVED is indicated, the transmitter is
not registered to the vehicle, if necessary,
reprogram and register the transmitter (see page
22-324).
• If KEYLESS ENTRY TRANSMITTER CODE IS NOT
RECEIVED is indicated, go to step 5.
5. Open the transmitter and check for water damage.
• If you find any water damage, replace the
transmitter, then reprogram and register the
transmitter (see page 22-324).
• If there is no water damage, go to step 6.
6. Replace the transmitter battery (A) with a new one,
and press lock or unlock button and check the
receive condition on the screen of the HDS.
• If KEYLESS ENTRY TRANSMITTER CODE IS
RECEIVED is indicated, the transmitter is OK.
• If KEYLESS ENTRY TRANSMITTR CODE IS NOT
RECEIVED is indicated, go to step 7.
(cont’d)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст