Honda Ridgeline. Manual — part 204
*01
16
14-201
A
B
A
C
D
E
8. Remove A/T clutch pressure control solenoid
valve C.
9. Remove the ATF joint pipes (A), the O-rings (B), the
ATF pipe (D), and the gasket (E).
10. Check the fluid passage of the solenoid valve for
contamination.
11. Connect the negative battery terminal to A/T clutch
pressure control solenoid valve C connector
terminal No. 2, and connect the positive battery
terminal to connector terminal No. 1. Make sure
A/T clutch pressure control solenoid valve C moves.
12. Disconnect one of the battery terminals, and check
the valve movement at the fluid passage in valve
body mounting surface. If the valve binds or moves
sluggishly, or if the solenoid valve does not operate,
replace A/T clutch pressure control solenoid valve
C.
13. Clean the mounting surfaces and fluid passages of
the solenoid valve body and the transmission
housing.
(cont’d)
17
18
19
14-202
Automatic Transmission
A/T Clutch Pressure Control Solenoid Valve C Test (cont’d)
A
B
A
B
C
D
6 x 1.0 mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
A
B
C
D
E
14. Install the 8 x 53 mm ATF joint pipe (A) with the
filter end into its mounting hole (B).
15. Check the height (A) of the 8 x 53 mm ATF joint
pipe (B) between the top (C) of the pipe and the
solenoid valve body mounting surface (D). The
height is about 7 mm (0.3 in.). If the height is over
7 mm (0.3 in.), push the pipe until it bottoms in the
accumulator body.
16. Install a new gasket (A) on the transmission
housing, and install the 8 x 34.5 mm ATF joint pipe
(B) with the filter end in the transmission housing
and 8 x 25.2 mm ATF pipe (D).
17. Install new O-rings (E) over the ATF joint pipes.
18. Install A/T clutch pressure control solenoid valve C.
19. Install the intake air duct and the intake manifold
cover.
*01
05
06
SJC8A00E10410612223KBAT10
14-203
A/T Clutch Pressure Control Solenoid Valve C Replacement
A
B
A
C
D
E
A
B
A
B
C
D
1. Remove the intake manifold cover and the intake
air duct.
2. Disconnect the A/T clutch pressure control solenoid
valve C connector.
3. Remove A/T clutch pressure control solenoid
valve C.
4. Remove the ATF joint pipes (A), the O-rings (B), the
ATF pipe (D), and the gasket (E).
5. Clean the mounting surfaces and fluid passages of
the solenoid valve body and the transmission
housing.
6. Install the 8 x 53 mm ATF joint pipe (A) with the
filter end into its mounting hole (B).
7. Check the height (A) of the 8 x 53 mm ATF joint
pipe (B) between the top (C) of the pipe and the
solenoid valve body mounting surface (D). The
height is about 7 mm (0.3 in.). If the height is over
7 mm (0.3 in.), push the pipe until it bottoms in the
accumulator body.
(cont’d)
07
14-204
Automatic Transmission
A/T Clutch Pressure Control Solenoid Valve C Replacement (cont’d)
6 x 1.0 mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
A
B
C
D
E
8. Install the new gasket (A) on the transmission
housing, and install the 8 x 34.5 mm ATF joint pipe
(B) with the filter end in the transmission housing
and 8 x 25.2 mm ATF pipe (D).
9. Install new O-rings (E) over the ATF joint pipes.
10. Install A/T clutch pressure control solenoid valve C.
11. Install the intake air duct and the intake manifold
cover.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст