Honda Ridgeline. Manual — part 26
33
03
04
02
5-14
Engine Assembly
Engine Installation (cont’d)
10 x 1.25 mm
44 N·m
(4.5 kgf·m, 33 lbf·ft)
A
A
B
A
A
10 x 1.25 mm
38 N·m
(3.9 kgf·m, 28 lbf·ft)
B
14 x 1.5 mm
103 N·m
(10.5 kgf·m, 75.9 lbf·ft)
D
12 x 1.25 mm
117 N·m
(11.9 kgf·m, 86.1 lbf·ft)
B
E
E
B
E
E
C
D
C
12 x 1.25 mm
74 N·m
(7.5 kgf·m,
54 N·m)
A
EQS02BMDXSB0
5. Install the engine support hanger (AAR-T-12566) to
the vehicle, then attach the hook to the slotted hole
in the engine hanger balance bar. Tighten the wing
nut (F) by hand to lift and support the engine/
transmission assembly.
6. Install new mounting bolts into the upper half of
the engine mount bracket. Tighten the bolts to the
specified torque.
7.
lift to full height.
8. Using the subframe adapter (A) and a jack, raise
the front subframe up to the body.
9. Loosely install the new front subframe mounting
bolts (four) (B), the 12 x 1.25 mm bolts (six) (C) (D),
and the stiffeners (E).
10. Align all reference marks (A) on the front subframe
(B) with the body, then tighten the bolts on the front
subframe to the specified torque.
11. Install the bolt retainers on both ends of the
subframe.
12. Remove the jack and front subframe adapter.
Remove the chain hoist, then raise the vehicle on the
04
06
07
05
5-15
B
10 x 1.25 mm
45 N·m (4.5 kgf·m, 33 lbf·ft)
A
10 x 1.25 mm
45 N·m (4.5 kgf·m, 33 lbf·ft)
10 x 1.25 mm
38 N·m
(3.9 kgf·m, 28 lbf·ft)
12 x 1.25 mm
54 N·m
(5.5 kgf·m, 40 lbf·ft)
10 x 1.25 mm
45 N·m
(4.5 kgf·m, 33 lbf·ft)
13. Torque the transmission lower rear mount nuts (A)
and transmission lower front mount nuts (B).
14. Torque the rear mount bolts.
15. Lower the vehicle on the lift.
16. Torque the new front mount nut.
17. Loosen the mounting bolts for the upper half of the
side engine mount bracket, then retighten them to
the specified torque.
18. Remove the engine hanger and balance bar.
19. Raise the vehicle on the lift to full height.
(cont’d)
09
10
11
5-16
Engine Assembly
Engine Installation (cont’d)
8 x 1.25 mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
A
B
20. Install the A/C compressor.
21. Install the power steering (P/S) hose (A), then install
the P/S hose on the clamp (B).
22. Connect the power steering pressure switch
connector.
23. Install the transfer assembly (see page 14-215).
24. Install the propeller shaft onto the transfer shaft
flange (see page 16-41).
25. Install a new set ring on the end of each driveshaft,
then install the driveshafts. Make sure each ring
‘‘clicks’’ into place in the differential and
intermediate shaft.
26. Connect the suspension lower arms to the knuckles
(see step 9 on page 18-20).
27. Connect the tie-rod end ball joints to the knuckles
(see step 15 on page 18-16).
28. Connect the stabilizer links (see page 18-20).
12
13
14
15
5-17
C
10 x 1.25 mm
54 N·m
(5.5 kgf·m, 40 lbf·ft)
8 x 1.25 mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
C
10 x 1.25 mm
33 N·m
(3.4 kgf·m, 25 lbf·ft)
B
A
B
10 x 1.25 mm
54 N·m
(5.5 kgf·m, 40 lbf·ft)
A
B
29. Install exhaust pipe A using new gaskets (B) and
new self-locking nuts (C).
30. Install the front subframe stiffener using new bolts.
31. Install the splash shield.
32. Install the front wheels.
33. Lower the vehicle on the lift.
34. Install the radiator (see page 10-12).
35. Install the upper radiator hose (A) and lower
radiator hose (B).
(cont’d)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст