Honda Ridgeline. Manual — part 251
01
02
SJC8A00E10474559752KBAT10
Special Tools Required
14-389
Transfer Hypoid Drive Gear Bearing Replacement
07749-0010000
07746-0010300
A
B
C
07749-0010000
07746-0010300
07LAD-PW50601
• Driver 07749-0010000
• Attachment, 42 x 47 mm 07746-0010300
• Attachment, 40 x 50 mm 07LAD-PW50601
1. Remove the tapered roller bearing (A) from the
transfer hypoid drive gear (B) with the driver,
attachment (42 x 47 mm), the bearing separator (C)
and the press.
2. Install a new bearing on the transfer hypoid drive
gear with the driver, attachment (42 x 47 mm),
attachment (40 x 50 mm), and the press.
01
02
SJC8A00E10474559773KDAT10
Special Tools Required
14-390
Transfer Assembly
Transfer Output Shaft (Hypoid Gear) Bearing Removal/Installation
C
D
B
A
07746-0030100
A
Driver, 40 mm I.D. 07746-0030100
1. Remove the tapered roller bearing (A) from the
transfer output shaft (hypoid gear) (B) with a
bearing separator (C) and a press. Place a shaft
protector (D) between the transfer output shaft and
the press to prevent damaging the shaft.
2. Install the 40 mm thrust shim (A) over the transfer
output shaft (hypoid gear).
3. Install the tapered roller bearing over the transfer
output shaft (hypoid gear) with the driver (40 mm
I.D.), and the press.
01
02
03
SJC8A00E10474559771KBAT00
Special Tools Required
14-391
Transfer Housing Tapered Roller Bearing Outer Race Replacement
B
A
C
A
B
C
07749-0010000
07746-0010400
A
• Driver 07749-0010000
• Attachment, 52 x 55 mm 07746-0010400
• Oil seal driver attachment 07JAD-PH80101
• Tapered bearing race installer A 07MAF-SP0011A
• Installer shaft 07MAF-SP0013A
NOTE: Replace the bearing with a new one whenever
the outer race is replaced.
1. Remove the 52 mm bearing outer race (A) and the
75 mm outer race (B) from the transfer housing (C).
NOTE: Some bearing outer races (52 mm and
75 mm) are press-fitted in the housing, and these
races are removed by heating the housing.
2. Remove the 58 mm bearing outer race (A) from the
transfer housing (B) by heating the housing to
about 212 °F (100 °C) with a heat gun (C). Remove
the 52 mm and the 75 mm outer races by heating, if
they are press-fitted. Do not heat the housing more
than 212 °F (100 °C).
3. Install the 52 mm bearing outer race (A) until it
bottoms in the transfer housing with the driver and
attachment (52 x 55 mm).
(cont’d)
04
05
14-392
Transfer Assembly
Transfer Housing Tapered Roller Bearing Outer Race Replacement (cont’d)
07MAF-SP0011A
07MAF-SP0013A
07JAD-PH80101
07MAF-SP0013A
A
B
C
07JAD-PH80101
07MAF-SP0013A
07MAF-SP0011A
D
B
C
A
D
4. Install the 75 mm bearing outer race (A) and the
58 mm outer race (B) in the transfer housing (C), set
the oil seal driver attachment and tapered bearing
race installer A attachments over the races, and
install the installer shaft through the attachments.
5. Tighten the installer shaft nut (D) to install the races
(A) (B) into the transfer housing (C) securely.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст