Honda Ridgeline. Manual — part 324
01
SJC8A00D14300014751MAAT00
Connection Point
Component
Connected to
Specified Torque Value
Note
19-33
Brake Hose and Line Inspection
A
B
C
D
E
A
E
C
C
B
1. Inspect the brake hoses for damage, deterioration, leaks, interference, and twisting.
2. Check the brake lines for damage, rusting, and leaks. Also check for bent brake lines.
3. Check for leaks at hose and line joints and connections, and retighten if necessary.
4. Check the master cylinder and VSA modulator-control unit for damage and leaks.
NOTE: Replace the brake hose clip whenever the brake hose is serviced.
A
Front brake caliper
Brake hose
34 N·m (3.5 kgf·m, 25 lbf·ft)
Banjo bolt
Bleed screw
9.0 N·m (0.9 kgf·m, 7.0 lbf·ft)
B
Rear brake caliper
Brake hose
34 N·m (3.5 kgf·m, 25 lbf·ft)
Banjo bolt
Bleed screw
9.0 N·m (0.9 kgf·m, 6.5 lbf·ft)
C
Brake hose
Brake line
15 N·m (1.5 kgf·m, 11 lbf·ft)
Flare nut
D
Master cylinder
Brake line
35 N·m (3.6 kgf·m, 26 lbf·ft)
Flare nut
E
VSA modulator-
control unit
Brake line
(14 mm nut)
30 N·m (3.1 kgf·m, 22 lbf·ft)
Flare nut
Brake line
(10 mm nut)
15 N·m (1.5 kgf·m, 11 lbf·ft)
Flare nut
01
02
03
04
SJC8A00D14300014751KBAT00
19-34
Conventional Brake Components
Brake Hose Replacement
A
B
C
A
B
C
C
10 x 1.0 mm
34 N·m
(3.5 kgf·m,
25 lbf·ft)
B
8 x 1.25 mm
22 N·m
(2.2 kgf·m,
16 lbf·ft)
A
D
D
10 x 1.0 mm
15 N·m
(1.5 kgf·m,
11 lbf·ft)
A
B
C
NOTE:
• Before reassembling, check that all parts are free of
dirt and other foreign particles.
• Replace parts with new ones whenever specified to
do so.
• Do not spill brake fluid on the vehicle; it may damage
the paint; if brake fluid gets on the paint, wash it off
immediately with water.
• To prevent the brake fluid from flowing, plug and
cover the hose ends and joints with a shop towel or
equivalent material.
1. Replace the brake hose (A) if the hose is twisted,
cracked, or leaking.
2. Disconnect the brake hose from the brake line (B)
using a 10 mm flare-nut wrench (C).
3. Remove and discard the brake hose clip (A) from
the brake hose (B).
4. Remove the banjo bolt (C), and disconnect the
brake hose from the caliper.
5. Remove the brake hose from the damper bracket.
6. Install the brake hose (A) on the damper bracket
with flange bolt (B) first, then connect the brake
hose to the caliper with the banjo bolt (C) and new
sealing washers (D).
7. Install the brake hose (A) on the upper brake hose
bracket (B) with a new brake hose clip (C).
8. Connect the brake line (D) to the brake hose.
9. After installing the brake hose, bleed the brake
system (see page 19-9).
10. Do the following check:
• Check the brake hose and line joint for leaks, and
tighten if necessary.
• Check the brake hoses for interference and
twisting.
01
SJC8A00D00060845111KBAT00
Exploded View
19-35
Parking Brake Cable Replacement
8 x 1.25 mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
PARKING BRAKE
CABLE A
EQUALIZER
8 x 1.25 mm
22 N·m
(2.2 kgf·m,
16 lbf·ft)
PARKING
BRAKE SWITCH
FLANGE NUT
8 x 1.25 mm
22 N·m
(2.2 kgf·m,
16 lbf·ft)
PARKING BRAKE
PEDAL ASSEMBLY
PARKING BRAKE PEDAL
PARKING BRAKE
RELEASE LEVER
RIGHT PARKING
BRAKE CABLE
LEFT PARKING
BRAKE CABLE
Multipurpose
(Sliding surface)
(cont’d)
Check for faulty
movement.
Check for smooth
operation.
Check for faulty
movement.
Check for faulty
movement.
02
19-36
Conventional Brake Components
Parking Brake Cable Replacement (cont’d)
B
C
A
NOTE: The parking brake cable must not be bent or
distorted. This will lead to stiff operation and premature
cable failure. Refer to the Exploded View as needed
during this procedure.
1. Remove the parking brake shoes, and disconnect
the parking brake cable from the brake shoe
(see page 19-28).
2. Remove the parking brake cable (A) from the
backing plate (B) using a 12 mm offset wrench (C).
3. Install the parking brake cable in the reverse order
of removal, and adjust the parking brake (see page
19-7). Apply the parking brake firmly ten times,
then adjust it again.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст