Honda Ridgeline. Manual — part 232
−
01
02
03
SJC8A00E10411239521KBAT00
Special Tools Required
14-313
Torque Converter Housing
Mainshaft Bearing and Oil Seal Replacement
A
07736-A01000B or
07736-A01000A
07749-0010000
07746-0010500
07749-0010000
07746-0010600
• Adjustable bearing puller, 25
40 mm
07736-A01000B or 07736-A01000A
• Driver 07749-0010000
• Attachment, 62 x 68 mm 07746-0010500
• Attachment, 72 x 75 mm 07746-0010600
1. Remove the mainshaft bearing and oil seal with the
adjustable bearing puller and a commercially
available 3/8 ’’-16 slide hammer (A).
2. Install the new mainshaft bearing until it bottoms in
the housing with the driver and attachment
(62 x 68 mm).
3. Install the new oil seal flush to the housing with the
driver and attachment (72 x 75 mm).
−
−
−
01
02
03
SJC8A00E10410917424KBAT00
Special Tools Required
14-314
Torque Converter Housing
Countershaft Bearing Replacement
A
07736-A01000B or
07736-A01000A
B
A
07749-0010000
07NAD-PX40100
C
D
B
A
• Adjustable bearing puller, 25
40 mm
07736-A01000B or 07736-A01000A
• Driver 07749-0010000
• Attachment, 78 x 80 mm 07NAD-PX40100
1. Remove the countershaft bearing from the torque
converter housing with the adjustable bearing
puller and a commercially available 3/8 ’’-16 slide
hammer (A).
2. Install the ATF guide plate (A) into the housing,
then install the new bearing (B) in the direction
shown.
3. Install the bearing (A) in the housing with the driver
and attachment (78 x 80 mm); install bearing outer
race notch-cut (B) to a depth (C) of 0
0.03 mm
(0
0.001 in.) below the housing surface (D).
−
−
01
*01
03
*02
SJC8A00E10411354202KBAT00
Special Tools Required
14-315
Secondary Shaft Bearing Replacement
B
A
A
07736-A01000B
07736-A01000A
07936-3710100
07936-8890300
07741-0010201
• Adjustable bearing puller, 25
40 mm
07736-A01000B or 07736-A01000A
• Bearing remover shaft set, 30 mm 07936-8890300
• Bearing remover shaft handle 07936-3710100
• Sliding hammer weight 07741-0010201
• Driver 07749-0010000
• Attachment, 37 x 40 mm 07746-0010200
• Attachment, 62 x 68 mm 07746-0010500
1. Remove the bolt, then remove the lock washer (A)
and bearing set plate (B).
2. Remove the secondary shaft bearing from the
torque converter housing with the adjustable
bearing puller (25
40 mm), and a commercially
available 3/8 ’’-16 slide hammer (A).
3. Remove the ATF guide collar from the torque
converter housing.
4. Remove the 29 x 39 x 9.5 mm secondary shaft
bearing from the torque converter housing with the
bearing remover shaft set (30 mm), bearing
remover shaft handle, and sliding hammer weight.
(cont’d)
05
06
07
08
14-316
Torque Converter Housing
Secondary Shaft Bearing Replacement (cont’d)
07749-0010000
07746-0010200
B
A
07749-0010000
07746-0010500
6 x 1.0 mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
A
B
5. Install the 29 x 39 x 9.5 mm bearing into the torque
converter housing with the driver and attachment
(37 x 40 mm).
6. Install the new O-rings (A) on the ATF guide collar
(B), then install the guide collar in the torque
converter housing.
7. Install the bearing in the direction shown in the
housing with the driver and attachment
(62 x 68 mm).
8. Check that the bearing groove aligns with the set
plate mounting surface, then install the set plate (A)
by aligning it with the bearing groove.
9. Install the new lock washer (B) and bolt, then bend
the lock tab of the lock washer against the bolt head.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст