Honda Ridgeline. Manual — part 368
01
02
SJC8A00J46127037901KBAT00
For Some Models (Driver’s seat)
20-110
Seats
Front Seat Lumbar Support Replacement
Fastener Locations
: Screw, 2
A
A
D
E
B
C
D
SRS components are located in this area. Review the
SRS component locations (see page 24-14) and the
precautions and procedures (see page 24-16) before
doing repairs or service.
NOTE:
• When prying with a flat-tip screwdriver, wrap it with
protective tape to prevent damage.
• Take care not to bend the cable.
• Take care not to tear the seams or damage the seat
covers.
• Put on gloves to protect your hands.
1. Remove these items:
• Lumbar support knob (see step 4 on page 20-111)
• Back panel (see step 5 on page 20-112)
2. Release the hook strips on the inside of the seat-
back (see step 6 on page 20-112).
3. Remove the screws securing the lumbar support
actuator (A).
4. Remove the metal clamps (A) and release the wire
(B) of the lumber support (C) from the retainers (D),
then remove the lumbar support and lumbar
support actuator (E) as an assembly.
5. Install the lumbar support in the reverse order of
removal, and note these items:
• To prevent wrinkles when installing a seat-back
cover, make sure the material is stretched evenly
over the pad before securing the hook strips.
• Replace the back panel clips with new ones.
• Replace the metal clips with new ones.
01
SJC8A00J46127053950KBAT00
Special Tools Required
20-111
Front Seat-back Cover Replacement
A
B
KTC trim tool set SOJATP2014
Available through the American Honda Tool and
Equipment Program; call 888-424-6857
SRS components are located in this area. Review the
SRS component locations (see page 24-14) and the
precautions and procedures (see page 24-16) before
doing repairs or service.
NOTE:
• Seats with a side airbag have a ‘‘SIDE AIRBAG’’ label
on the seat-back. Because the component parts (seat-
back cover, cushion, etc.) of seats with and without
airbags are different, make sure you install only the
correct replacement parts.
• Do not repair any tears or frayed spots of the seat-
back cover. If necessary, replace the seat-back cover.
• Take care not to tear the seams or damage the seat
covers.
• On the passenger’s seat, do not touch the OPDS
sensor in the seat-back pad, and keep it away from oil.
Oil can corrode the sensor causing it to fail.
• Put on gloves to protect your hands.
• Use the appropriate tool from the KTC trim tool set to
avoid damage when prying components.
1. Remove the front seat (see page 20-97).
2. Remove the seat-back (see page 20-99).
3. Remove the head restraint.
4. If equipped, remove the clip (A), then remove the
lumbar support handle (B).
(cont’d)
02
03
04
05
Driver’s seat-back
Passenger’s seat-back
20-112
Seats
Front Seat-back Cover Replacement (cont’d)
Fastener Locations
: Clip, 2
C
B
A
A
A
A
A
A
B
C
B
A
D
F
F
E
C
B
5. Detach the clips and hooks (A) by pulling the
bottom of the back panel (B) back, then gently pull
down the panel to release the hooks (C) from the
seat-back frame, and remove the panel.
6. Release the hook strips (A), then loosen the seat-
back cover (B).
7. Pull the recline motor subharness (A) (some driver’s
seats), seat-back heater harness (B) (some driver’s
seats), side airbag harness (C), lumbar support
motor harness (D) (some driver’s seats), and the
OPDS/ODS harness (E) (passenger’s seat) out
through the harness guides (F).
06
07
08
09
20-113
A
D
C
A
A
B
B
B
C
A
A
A
B
C
A
A
B
A
8. Release the front hook (A) and rear hook (B) of the
reinforcing cloth (C) from seat-back frame (D).
9. Pinch the tabs on the ends of the head restraint
guides (A), and remove them from the seat-back.
10. From the back of the seat-back, pass both lower
retainers (A) through the slots in the seat-back pad,
and release the clips (B) and inside springs (C).
11. Pull back the edge of the seat-back cover all the
way around, and release the clips (A), then remove
the seat-back cover.
(cont’d)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст