Honda Ridgeline. Manual — part 557
01
SJC8A00K791000R111XFAAT10
−
−
−
−
DTC 11-1x (‘‘x’’ can be 0 thru 9 or A thru F):
DTC 11-4x (‘‘x’’ can be 0 thru 9 or A thru F):
Special Tools Required
YES
NO
YES
NO
24-53
DTC Troubleshooting
A
07XAZ-SZ30100
07SAZ-TB4011A
Open in Driver’s Airbag First Inflator
Open in Driver’s Airbag Second Inflator
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead F 07XAZ-SZ30100
NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-16) and General Troubleshooting Information
(see page 24-27).
1. Clear the DTC memory (see page 24-28).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, the system is OK at this
time. Go to Troubleshooting Intermittent Failures
(see page 24-29). If another DTC is indicated,
troubleshoot the DTC.
3. Turn the ignition switch OFF. Disconnect the
negative cable from the battery, and wait for 3
minutes.
4. Disconnect the driver’s airbag 4P connector (A)
from the cable reel.
5. Connect the SRS inflator simulator (2
connectors) and simulator lead F to the cable reel.
6. Reconnect the negative cable to the battery.
7. Clear the DTC memory.
8. Read the DTC (see page 24-27).
Go to step 9.
Open in the driver’s airbag first or second
inflator; replace the driver’s airbag (see page
24-174).
(cont’d)
Does the SRS indicator stay on, and is DT C 11-1x
or 11-4x indicated?
Is DT C 11-1x or 11-4x indicated?
02
03
−
−
−
−
YES
NO
YES
NO
24-54
SRS
DTC Troubleshooting (cont’d)
A
07XAZ-SZ30100
07SAZ-TB4011A
07XAZ-SZ30100
DASHBOARD
WIRE HARNESS
4P CONNECTOR
9. Turn the ignition switch OFF. Disconnect the
negative cable from the battery, and wait for 3
minutes.
10. Disconnect the dashboard wire harness 4P
connector (A) from the cable reel.
11. Connect the SRS inflator simulator (2
connectors) and the simulator lead to dashboard
wire harness.
12. Reconnect the negative cable to the battery.
13. Clear the DTC memory.
14. Read the DTC.
Go to step 15.
Open in the cable reel; replace the cable reel
(see page 24-185).
15. Turn the ignition switch OFF. Disconnect the
negative cable from the battery, and wait for 3
minutes.
16. Disconnect SRS unit connector A (28P) from the
SRS unit (see step 7 on page 24-26).
17. Disconnect the SRS inflator simulator from the SRS
simulator lead. Do not disconnect the simulator
lead from the dashboard wire harness 4P connector.
18. Measure the resistance between the terminals of
both SRS simulator leads. There should be 1
or
less.
Faulty SRS unit or poor connection at SRS
unit connector A (28P) and the SRS unit. Check the
connection between the connector and the SRS
unit. If the connection is OK, replace the SRS unit
(see page 24-188).
Open in the dashboard wire harness; replace
the dashboard wire harness.
Is DT C 11-1x or 11-4x indicated?
Is the r esistance as specif ied?
01
SJC8A00K791000R113XFAAT00
−
−
−
−
DTC 11-3x (‘‘x’’ can be 0 thru 9 or A thru F):
DTC 11-6x (‘‘x’’ can be 0 thru 9 or A thru F):
Special Tools Required
YES
NO
YES
NO
24-55
A
07XAZ-SZ30100
07SAZ-TB4011A
Short to Another Wire or Decreased
Resistance in Driver’s Airbag First Inflator
Short to Another Wire or Decreased
Resistance in Driver’s Airbag Second Inflator
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead F 07XAZ-SZ30100
• SRS short canceller 070AZ-SAA0100
NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-16) and General Troubleshooting Information
(see page 24-27).
1. Clear the DTC memory (see page 24-28).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, the system is OK at this
time. Go to Troubleshooting Intermittent Failures
(see page 24-29). If another DTC is indicated,
troubleshoot the DTC.
3. Turn the ignition switch OFF. Disconnect the
negative cable from the battery, and wait for 3
minutes.
4. Disconnect the driver’s airbag 4P connector (A)
from the cable reel.
5. Connect the SRS inflator simulator (2
connectors) and simulator lead F to the cable reel.
6. Reconnect the negative cable to the battery.
7. Clear the DTC memory.
8. Read the DTC (see page 24-27).
Go to step 9.
Short in the driver’s airbag first or second
inflator; replace the driver’s airbag (see page
24-174).
(cont’d)
Does the SRS indicator stay on, and is DT C 11-3x
or 11-6x indicated?
Is DT C 11-3x or 11-6x indicated?
02
03
−
−
−
−
YES
NO
YES
NO
24-56
SRS
DTC Troubleshooting (cont’d)
A
07XAZ-SZ30100
07SAZ-TB4011A
07XAZ-SZ30100
DASHBOARD
WIRE HARNESS
4P CONNECTOR
9. Turn the ignition switch OFF. Disconnect the
negative cable from the battery, and wait for 3
minutes.
10. Disconnect the dashboard wire harness 4P
connector (A) from the cable reel.
11. Connect the SRS inflator simulator (2
connectors) and simulator lead to the dashboard
wire harness.
12. Reconnect the negative cable to the battery.
13. Clear the DTC memory.
14. Read the DTC.
Go to step 15.
Short in the cable reel; replace the cable reel
(see page 24-185).
15. Turn the ignition switch OFF. Disconnect the
negative cable from the battery, and wait for 3
minutes.
16. Disconnect SRS unit connector A (28P) from the
SRS unit (see step 7 on page 24-26).
17. Disconnect the SRS inflator simulator from the SRS
simulator lead.
18. Connect SRS short cancellers (070AZ-SAA0100) to
the No. 7 and No. 8 terminals and the No. 1 and
No. 2 terminals of SRS unit connector A (28P)
(see page 24-22).
19. Measure the resistance between the terminals of
both SRS simulator leads. There should be an open
circuit or at least 1 M
.
Faulty SRS unit or poor connection at SRS
unit connector A (28P) and the SRS unit. Check the
connection between the connector and the SRS
unit. If the connection is OK, replace the SRS unit
(see page 24-188).
Short in the dashboard wire harness; replace
the dashboard wire harness.
Is DT C 11-3x or 11-6x indicated?
Is the r esistance as specif ied?
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст